ISO 5179:2021
$19.50
Investigation of brazeability with spreading and gap-filling test
| Published By | Publication Date | Number of Pages |
| ISO | 2021-03 | 20 |
This document specifies three test methods for investigating brazeability.
A spreading test shows testing method with measurement of the spread area of the filler metals.
A T-joint test describes a scheme to construct a T-shape design by the test pieces and a testing method.
A varying gap test describes a test piece and a testing method for assessing the influence of the various parameters which can influence brazing during manufacture as a function of clearances.
Related products
-
BS EN ISO 6179:2001
Rubber, vulcanized or thermoplastic. Rubber sheets and rubber-coated fabrics. Determination of transmission rate of volatile…
-
BS EN ISO 5178:2011
Destructive tests on welds in metallic materials. Longitudinal tensile test on weld metal in fusion…
-
BS ISO 15179:2012
Hot-rolled twin-roll cast steel sheet of structural quality and high strength steel Published By Publication…
-
BS EN ISO 179-1:2001:2006 Edition
Plastics. Determination of Charpy impact properties – Non-instrumented impact test Published By Publication Date Number…
-
ISO 179-2:2020
Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test Published By…
-
BS EN ISO 5079:2020
Textile fibres. Determination of breaking force and elongation at break of individual fibres Published By…
-
BS ISO 5189:2023
Fine ceramics (advanced ceramics, advanced technical ceramics). Methods for chemical analysis of metal impurities in…
-
BS ISO 5119:2023
Low temperature sealing capability of elastomeric seals. Test methods Published By Publication Date Number of…
-
ISO 5079:2020
Fibres textiles — Détermination de la force de rupture et de l’allongement de rupture des…
-
BSI PD ISO/TR 7179:2023
Service excellence. Practices for achieving service excellence Published By Publication Date Number of Pages BSI…
-
BS EN ISO 5139:2023
Dentistry. Polymer-based composite machinable blanks Published By Publication Date Number of Pages BSI 2023 28
-
ISO 5178:2001
Destructive tests on welds in metallic materials — Longitudinal tensile test on weld metal in…
-
ISO 15179:2022
Hot-rolled twin-roll cast steel sheet of structural quality and high strength steel Published By Publication…
-
ISO 5129:2001/Amd 1:2013
Acoustics — Measurement of sound pressure levels in the interior of aircraft during flight —…
-
BS EN ISO 5079:2020
Textile fibres. Determination of breaking force and elongation at break of individual fibres Published By…
-
BS EN ISO 5179:2023
Investigation of brazeability with spreading and gap-filling test Published By Publication Date Number of Pages…
-
BS EN ISO 5173:2023
Destructive tests on welds in metallic materials. Bend tests Published By Publication Date Number of…
-
BS ISO 5149-4:2022
Refrigerating systems and heat pumps. Safety and environmental requirements – Operation, maintenance, repair and recovery…
-
ISO 5173:2009/Amd 1:2011
Destructive tests on welds in metallic materials — Bend tests — Amendment 1 Published By…
-
BS EN ISO 179-2:2020
Plastics. Determination of Charpy impact properties – Instrumented impact test Published By Publication Date Number…
-
BS EN ISO 179-1:2023
Plastics. Determination of Charpy impact properties – Non-instrumented impact test Published By Publication Date Number…
-
BS ISO 5149-3:2014+A1:2021
Refrigerating systems and heat pumps. Safety and environmental requirements – Installation site Published By Publication…
-
BS EN ISO 179-1:2023 – TC
Tracked Changes. Plastics. Determination of Charpy impact properties – Non-instrumented impact test Published By Publication…
-
BSI 22/30422379 DC 2022
BS EN ISO 5139. Dentistry. Polymer-based composite machinable blanks Published By Publication Date Number of…
-
BS EN ISO 1179-2:2022
Connections for general use and fluid power. Ports and stud ends with ISO 228-1 threads…
-
BS ISO 5879:2023
Space systems. Ground test for the separation between a launch vehicle and a spacecraft. Requirements…
-
BS ISO 15179:2022
Hot-rolled twin-roll cast steel sheet of structural quality and high strength steel Published By Publication…
-
BS ISO 4179:2024 – TC
Tracked Changes. Ductile iron pipes and fittings for pressure and non-pressure pipelines. Cement mortar lining…
-
BS EN ISO 5079:2020
Textile fibres. Determination of breaking force and elongation at break of individual fibres Published By…
-
BS EN ISO 179-2:1999+A1:2012
Plastics. Determination of Charpy impact properties – Instrumented impact test Published By Publication Date Number…
-
BS EN ISO 5173:2010+A1:2011
Destructive tests on welds in metallic materials. Bend tests Published By Publication Date Number of…
-
ISO 5129:2001
Acoustics — Measurement of sound pressure levels in the interior of aircraft during flight Published…
-
BS ISO 5179:2021
Investigation of brazeability with spreading and gap-filling test Published By Publication Date Number of Pages…
-
BS ISO 5129:2001+A1:2013
Acoustics. Measurement of sound pressure levels in the interior of aircraft during flight Published By…
-
ISO 5172:2006/Amd 1:2012
Gas welding equipment — Blowpipes for gas welding, heating and cutting — Specifications and tests…
-
BSI 20/30404355 DC 2020
BS ISO 5179. Investigation of brazeability with spreading and gap-filling test Published By Publication Date…
-
BS EN ISO 1179-2:2022 – TC
Tracked Changes. Connections for general use and fluid power. Ports and stud ends with ISO…
-
BS EN ISO 5173:2023
Destructive tests on welds in metallic materials. Bend tests Published By Publication Date Number of…
-
BS ISO 5149-1:2014+A2:2021
Refrigerating systems and heat pumps. Safety and environmental requirements – Definitions, classification and selection criteria…
-
ISO 15179:2012
Hot-rolled twin-roll cast steel sheet of structural quality and high strength steel Published By Publication…
