ISO 7425-1:1988
$19.50
Hydraulic fluid power — Housings for elastomer-energized, plastic-faced seals — Dimensions and tolerances — Part 1: Piston seal housings
| Published By | Publication Date | Number of Pages |
| ISO | 1988-11 | 9 |
This part specifies the dimensions and associated tolerances for a series of housings to accomodate seals used in reciprocating applications. Does not stipulate details of seal design. This part applies only to the dimensional characteristics of products. Does not apply to their functional characteristics. Figure 1 contains an example of housing. Table 2 covers dimensions and tolerances of housings for bore diameters from 16 to 500 mm.
Related products
-
BS A 295:1985
Methods of test for self-locking nuts with maximum operating temperature less than or equal to…
-
BS EN 12475-1:1998
Classification of dense shaped refractory products – Alumina-silica products Published By Publication Date Number of…
-
BS ISO 7425-2:2021
Hydraulic fluid power cylinders. Dimensions and tolerances of housings for elastomer-energized, plastic-faced seals – Rod…
-
ISO 3223:1998
Aerospace — Nuts, anchor, self-locking, fixed, two lug, with counterbore, with MJ threads, classifications: 1…
-
BS A 324:1998
Nuts, bihexagonal, self-locking, MJ threads, classifications: 1100 MPa (at ambient temperature)/425°C, 1100 MPa (at ambient…
-
ISO 3222:1998
Aerospace — Nuts, anchor, self-locking, fixed, closed corner, reduced series, with counterbore, with MJ threads,…
-
BS 7445-1:1991
Description and measurement of environmental noise – Guide to quantities and procedures Published By Publication…
-
BS 7425-1:1991
Abrasive grains – Method for the determination of the bulk density of macrograins Published By…
-
BS 5600-3.3:1987
Powder metallurgical materials and products. Methods of testing sintered metal materials and products, excluding hardmetals…
-
BS 4425:1988
Specification for dental casting gold alloys Published By Publication Date Number of Pages BSI 1988…
-
BS 4219-3:1985
Slotted set screws: metric series – Specification for slotted set screws with long dog point…
-
BS 6984:1988:1989 Edition
Specification for dimensions of housings for elastomer-energized plastic-faced hydraulic seals in reciprocating applications Published By…
-
BS ISO 362:1998
Acoustics. Measurement of noise emitted by accelerating road vehicles. Engineering method Published By Publication Date…
-
BS 6070-2:1981
Methods of sampling and test for sodium carbonate for industrial use – Determination of chloride…
-
ISO 3168:1998
Aerospace — Nuts, anchor, self-locking, fixed, single lug, with counterbore, with MJ threads, classifications: 1…
-
ISO 3224:1998
Aerospace — Nuts, anchor, self-locking, floating, single lug, with counterbore, with MJ threads, classifications: 1…
-
BS 6783-6:1986
Sampling and analysis of nickel, ferronickel and nickel alloys – Method for determination of sulphur…
-
BS EN 1094-2:1999
Insulating refractory products – Classification of shaped products Published By Publication Date Number of Pages…
-
BS 6070-3:1981
Methods of sampling and test for sodium carbonate for industrial use – Determination of non-volatile…
-
BS 7925-2:1998
Software testing – Software component testing Published By Publication Date Number of Pages BSI 1998…
-
ISO 9156:1998
Aerospace — Nuts, anchor, self-locking, fixed, 90 degrees corner, reduced series, with counterbore, with MJ…
-
BS 6762-3:1989
Services for leisure accommodation vehicles and transportable accommodation units – Specification for oil-fired heating systems…
-
BS EN 12475-3:1998
Classification of dense shaped refractory products – Basic products containing from 7% to 30% residual…
-
BS 7025:1988
Method for preparation of test codes of engineering grade for measurement at the operator’s or…
-
ISO 3225:1998
Aerospace — Nuts, anchor, self-locking, fixed, two lug, reduced series, with counterbore, with MJ threads,…
-
BS EN ISO 7625:2010
Sintered metal materials, excluding hardmetals. Preparation of samples for chemical analysis for determination of carbon…
-
ISO 3209:1998
Aerospace — Nuts, anchor, self-locking, floating, two lug, with counterbore, with MJ threads, classifications: 1…
-
ISO 3221:1998
Aerospace — Nuts, anchor, self-locking, fixed, 90 degrees corner, with counterbore, with MJ threads, classifications:…
-
JIS B 1117:2010
Slotted set screws Published By Publication Date Number of Pages JIS 2010-09-21 17
-
BS EN 27435:1992
Slotted set screws with long dog point Published By Publication Date Number of Pages BSI…
-
ISO 3191:1998
Aerospace — Nuts, anchor, self-locking, fixed, single lug, reduced series, with counterbore, with MJ threads,…
-
BS 7125:1989
Specification for transformers for resistance welding machines Published By Publication Date Number of Pages BSI…
-
BS EN 60598-2-6:1995
Luminaires. Particular requirements – Luminaires with built-in transformers for filament lamps Published By Publication Date…
-
BS EN ISO 1927-1:2012
Monolithic (unshaped) refractory products – Introduction and classification Published By Publication Date Number of Pages…
-
BS EN 12475-2:1998
Classification of dense shaped refractory products – Basic products containing less than 7% residual carbon…
-
BS A 327:1998
Nuts, bihexagonal, self-locking, with counterbore and MJ threads, classifications: 1100 MPa (at ambient temperature)/425°C, 1100…
-
BS EN 60598-2-6:1995
Luminaires. Particular requirements – Luminaires with built-in transformers for filament lamps Published By Publication Date…
-
IEEE 29119-2-2021(Redline)
ISO/IEC/IEEE International Standard – Software and systems engineering – Software testing — Part 2: Test…
-
BS ISO 7425-1:2021
Hydraulic fluid power cylinders. Dimensions and tolerances of housings for elastomer-energized, plastic-faced seals – Piston…
-
ISO 197-5:1980
Copper and copper alloys — Terms and definitions — Part 5: Methods of processing and…
