MN MinnesotaMechFuelGasPlumbingCodes 2009
$54.17
Minnesota State Mechanical, Fuel Gas, and Plumbing Codes Chapters 1346 and 4715
| Published By | Publication Date | Number of Pages |
| MN | 2009 | 450 |
This is a fully integrated custom code based on the 2006 International Mechanical Code and 2006 International Fuel Gas Code®.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | 2009 MINNESOTA STATE MECHANICAL, FUEL GAS AND PLUMBING CODES, CHAPTERS 1346 AND 4715 |
| 2 | COPYRIGHT |
| 3 | NOTE TO USERS |
| 5 | TABLE OF CONTENTS MINNESOTA RULES, CHAPTER 1300 |
| 7 | MINNESOTA RULES, CHAPTER 1300 1300.0010 ADMINISTRATION 1300.0020 TITLE 1300.0030 PURPOSE AND APPLICATION 1300.0040 SCOPE 1300.0050 CHAPTERS OF MINNESOTA STATE BUILDING CODE |
| 8 | 1300.0060 OPTIONAL ADMINISTRATION 1300.0070 DEFINITIONS |
| 9 | 1300.0080 CODE ADOPTION AND AMENDMENTS |
| 10 | 1300.0090 DEPARTMENT OF BUILDING SAFETY 1300.0100 [REPEALED, 19 SR 1340] 1300.0110 DUTIES AND POWERS OF BUILDING OFFICIAL |
| 11 | 1300.0120 PERMITS |
| 13 | 1300.0130 CONSTRUCTION DOCUMENTS |
| 14 | 1300.0140 VIOLATIONS 1300.0150 VIOLATIONS, PENALTY 1300.0160 FEES |
| 15 | 1300.0170 STOP WORK ORDER 1300.0180 UNSAFE BUILDINGS OR STRUCTURES 1300.0190 TEMPORARY STRUCTURES AND USES |
| 16 | 1300.0200 [REPEALED, 19 SR 1340] 1300.0210 INSPECTIONS |
| 17 | 1300.0220 CERTIFICATE OF OCCUPANCY 1300.0230 BOARD OF APPEALS |
| 18 | 1300.0240 DISCLAIMER CLAUSE 1300.0250 SEVERABILITY |
| 19 | MINNESOTA MECHANICAL CODE TABLE OF CONTENTS MINNESOTA MECHANICAL CODE |
| 22 | SYMBOLS AND NOTATIONS IN THE CODE |
| 23 | MINNESOTA RULES CHAPTER 1346 MINNESOTA MECHANICAL CODE 1346.0050 INCORPORATION BY REFERENCE 1346.0060 REFERENCES TO OTHER INTERNATIONAL CODE COUNCIL (ICC) CODES |
| 25 | CHAPTER 1 ADMINISTRATION SECTION 101 SCOPE SECTION 102 EXISTING INSTALLATIONS SECTION 103 MAINTENANCE SECTION 104 ADDITIONS, ALTERATIONS, RENOVATIONS, OR REPAIRS SECTION 105 WORK EXEMPT FROM PERMIT SECTION 106 REQUIRED INSPECTIONS |
| 26 | SECTION 107 INSPECTIONS AND TESTING SECTION 108 AUTHORITY TO CONDEMN MECHANICAL SYSTEMS |
| 27 | SECTION 109 AUTHORITY TO ORDER DISCONNECTION OF ENERGY SOURCES SECTION 110 CONNECTION AFTER ORDER TO DISCONNECT |
| 29 | CHAPTER 2 DEFINITIONS SECTION 201 GENERAL SECTION 202 GENERAL DEFINITIONS |
| 41 | CHAPTER 3 GENERAL REGULATIONS SECTION 301 GENERAL |
| 42 | SECTION 302 PROTECTION OF STRUCTURE |
| 43 | SECTION 303 EQUIPMENT AND APPLIANCE LOCATION SECTION 304 INSTALLATION |
| 44 | SECTION 305 PIPING SUPPORT |
| 45 | TABLE 305.4 PIPING SUPPORT SPACINGa SECTION 306 ACCESS AND SERVICE SPACE |
| 47 | SECTION 307 CONDENSATE DISPOSAL SECTION 308 CLEARANCE REDUCTION |
| 48 | TABLE 308.6 CLEARANCE REDUCTION METHODS |
| 49 | [B] SECTION 309 TEMPERATURE CONTROL [F] SECTION 310 EXPLOSION CONTROL [F] SECTION 311 SMOKE AND HEAT VENTS SECTION 312 HEATING AND COOLING LOAD CALCULATIONS |
| 51 | CHAPTER 4 VENTILATION SECTION 401 GENERAL TABLE 401.5 OPENING SIZES IN LOUVERS, GRILLES AND SCREENS PROTECTING OUTDOOR EXHAUST AND AIR INTAKE OPENINGS SECTION 402 NATURAL VENTILATION |
| 52 | SECTION 403 MECHANICAL VENTILATION EQUATION 4-1 |
| 53 | SECTION 404 ENCLOSED PARKING GARAGES SECTION 405 SYSTEMS CONTROL SECTION 406 VENTILATION OF UNINHABITED SPACES |
| 55 | CHAPTER 5 EXHAUST SYSTEMS SECTION 501 GENERAL |
| 57 | TABLE 501.3.1 PROCEDURE TO DETERMINE MAKEUP AIR QUANTITY FOR EXHAUST EQUIPMENT IN DWELLINGS |
| 58 | TABLE 501.3.2 MAKEUP AIR OPENING SIZING TABLE FOR NEW AND EXISTING DWELLINGS |
| 59 | TABLE 501.3.3(1) PROCEDURE TO DETERMINE MAKEUP AIR QUANTITY FOR EXHAUST EQUIPMENT IN EXISTING DWELLINGS (Refer to Item 4 in Section 501.3.3 to determine applicability of this table) |
| 60 | TABLE 501.3.3(2) PROCEDURE TO DETERMINE MAKEUP AIR QUANTITY FOR EXHAUST EQUIPMENT IN EXISTING DWELLINGS (Refer to Item 5 in Section 501.3.3 to determine applicability of this table) |
| 61 | TABLE 501.3.3(3) PROCEDURE TO DETERMINE MAKEUP AIR QUANTITY FOR EXHAUST EQUIPMENT IN EXISTING DWELLINGS (Refer to Item 6 in Section 501.3.3 to determine applicability of this table) |
| 62 | SECTION 502 REQUIRED SYSTEMS EQUATION 5-1 |
| 68 | SECTION 503 MOTORS AND FANS SECTION 504 CLOTHES DRYER EXHAUST |
| 69 | SECTION 505 DOMESTIC KITCHEN EXHAUST EQUIPMENT SECTION 506 COMMERCIAL KITCHEN HOOD VENTILATION SYSTEM DUCTS AND EXHAUST EQUIPMENT |
| 70 | SECTION 507 COMMERCIAL KITCHEN HOODS |
| 72 | SECTION 508 COMMERCIAL KITCHEN MAKEUP AIR |
| 73 | SECTION 509 FIRE SUPPRESSION SYSTEMS SECTION 510 HAZARDOUS EXHAUST SYSTEMS |
| 74 | TABLE 510.8 MINIMUM DUCT THICKNESS TABLE 510.8.2 CLEARANCE TO COMBUSTIBLES |
| 75 | SECTION 511 DUST, STOCK AND REFUSE CONVEYING SYSTEMS TABLE 511.2 CONSTRUCTION, CLEARANCE AND TERMINATION REQUIREMENTS FOR SINGLE-WALL METAL CHIMNEYS |
| 76 | SECTION 512 SUBSLAB SOIL EXHAUST SYSTEMS SECTION 513 SMOKE CONTROL SYSTEMS |
| 77 | EQUATION 5-2 EQUATION 5-3 |
| 78 | EQUATION 5-4 |
| 79 | SECTION 514 ENERGY RECOVERY VENTILATION SYSTEMS |
| 81 | CHAPTER 6 DUCT SYSTEMS SECTION 601 GENERAL SECTION 602 PLENUMS |
| 82 | SECTION 603 DUCT CONSTRUCTION AND INSTALLATION |
| 83 | TABLE 603.4 DUCT CONSTRUCTION MINIMUM SHEET METAL THICKNESSES FOR SINGLE DWELLING UNITS |
| 84 | DUCT SEALING SECTION 604 INSULATION |
| 85 | MINIMUM REQUIRED DUCT INSULATION (See notes for explanations) SECTION 605 AIR FILTERS |
| 86 | SECTION 606 SMOKE DETECTION SYSTEMS CONTROL [B] SECTION 607 DUCT AND TRANSFER OPENINGS |
| 87 | TABLE 607.3.1 FIRE DAMPER RATING |
| 91 | CHAPTER 7 COMBUSTION AIR SECTION 701 GENERAL SECTION 702 INDOOR AIR SECTION 703 OUTDOOR AIR |
| 92 | SECTION 704 COMBINED USE OF INDOOR AND OUTDOOR AIR (CONDITION 1) SECTION 705 COMBINED USE OF INDOOR AND OUTDOOR AIR (CONDITION 2) SECTION 706 FORCED COMBUSTION AIR SUPPLY |
| 93 | SECTION 707 DIRECT CONNECTION SECTION 708 COMBUSTION AIR DUCTS SECTION 709 OPENING OBSTRUCTIONS SECTION 710 OPENING LOCATION AND PROTECTION |
| 95 | CHAPTER 8 CHIMNEYS AND VENTS SECTION 801 GENERAL |
| 96 | SECTION 802 VENTS TABLE 802.2 VENT APPLICATION |
| 97 | SECTION 803 CONNECTORS TABLE 803.9(1) MINIMUM CHIMNEY CONNECTOR THICKNESS FOR LOW-HEAT APPLIANCES TABLE 803.9(2) MINIMUM CHIMNEY CONNECTOR THICKNESS FOR MEDIUM- AND HIGH-HEAT APPLIANCES |
| 98 | TABLE 803.10.4 CHIMNEY CONNECTOR SYSTEMS AND CLEARANCESTO COMBUSTIBLE WALL MATERIALS FOR DOMESTIC HEATING APPLIANCES TABLE 803.10.6 CONNECTOR CLEARANCES TO COMBUSTIBLES SECTION 804 DIRECT-VENT, INTEGRAL VENT AND MECHANICAL DRAFT SYSTEMS |
| 99 | SECTION 805 FACTORY-BUILT CHIMNEYS |
| 100 | SECTION 806 METAL CHIMNEYS |
| 101 | CHAPTER 9 SPECIFIC APPLIANCES, FIREPLACES AND SOLID FUEL-BURNING EQUIPMENT SECTION 901 GENERAL SECTION 902 MASONRY FIREPLACES SECTION 903 FACTORY-BUILT FIREPLACES SECTION 904 PELLET FUEL-BURNING APPLIANCES SECTION 905 FIREPLACE STOVES AND ROOM HEATERS SECTION 906 FACTORY-BUILT BARBECUE APPLIANCES SECTION 907 INCINERATORS AND CREMATORIES SECTION 908 COOLING TOWERS, EVAPORATIVE CONDENSERS AND FLUID COOLERS |
| 102 | SECTION 909 VENTED WALL FURNACES SECTION 910 FLOOR FURNACES SECTION 911 DUCT FURNACES SECTION 912 INFRARED RADIANT HEATERS SECTION 913 CLOTHES DRYERS |
| 103 | SECTION 914 SAUNA HEATERS SECTION 915 ENGINE AND GAS TURBINE-POWERED EQUIPMENT AND APPLIANCES SECTION 916 POOL AND SPA HEATERS SECTION 917 COOKING APPLIANCES SECTION 918 FORCED-AIR WARM-AIR FURNACES |
| 104 | SECTION 919 CONVERSION BURNERS SECTION 920 UNIT HEATERS SECTION 921 VENTED ROOM HEATERS |
| 105 | SECTION 922 KEROSENE AND OIL-FIRED STOVES SECTION 923 SMALL CERAMIC KILNS SECTION 924 STATIONARY FUEL CELL POWER SYSTEMS SECTION 925 MASONRY HEATERS SECTION 926 GASEOUS HYDROGEN SYSTEMS |
| 107 | CHAPTER 10 BOILERS, WATER HEATERS AND PRESSURE VESSELS SUBPART 1. DEPARTMENT OF LABOR AND INDUSTRY BOILERS SUBPART 2. HIGH PRESSURE PIPING FOR BOILERS SECTION 1001 GENERAL SECTION 1002 WATER HEATERS |
| 108 | SECTION 1003 PRESSURE VESSELS SECTION 1004 BOILERS SECTION 1005 BOILER CONNECTIONS SECTION 1006 SAFETY AND PRESSURE RELIEF VALVES AND CONTROLS |
| 109 | SECTION 1007 BOILER LOW-WATER CUTOFF SECTION 1008 STEAM BLOWOFF VALVE SECTION 1009 HOT WATER BOILER EXPANSION TANK |
| 110 | EQUATION 10-1 SECTION 1010 GAUGES SECTION 1011 TESTS |
| 111 | CHAPTER 11 REFRIGERATION SECTION 1101 GENERAL SECTION 1102 SYSTEM REQUIREMENTS |
| 112 | SECTION 1103 REFRIGERATION SYSTEM CLASSIFICATION SECTION 1104 SYSTEM APPLICATION REQUIREMENTS |
| 113 | [F] TABLE 1103.1 REFRIGERANT CLASSIFICATION, AMOUNT AND TLV-TWA |
| 114 | [F] TABLE 1103.1—continued REFRIGERANT CLASSIFICATION, AMOUNT AND TLV-TWA |
| 115 | [F] TABLE 1103.1—continued REFRIGERANT CLASSIFICATION, AMOUNT AND TLV-TWA |
| 116 | TABLE 1104.3.2 MAXIMUM PERMISSIBLE QUANTITIES OF REFRIGERANTS |
| 117 | SECTION 1105 MACHINERY ROOM, GENERAL REQUIREMENTS EQUATION 11-1 |
| 118 | EQUATION 11-2 SECTION 1106 MACHINERY ROOM, SPECIAL REQUIREMENTS SECTION 1107 REFRIGERANT PIPING |
| 119 | SECTION 1108 FIELD TEST |
| 120 | [F] SECTION 1109 PERIODIC TESTING |
| 121 | CHAPTER 12 HYDRONIC PIPING SECTION 1201 GENERAL SECTION 1202 MATERIAL TABLE 1202.4 HYDRONIC PIPE TABLE 1202.4—continued HYDRONIC PIPE TABLE 1202.5 HYDRONIC PIPE FITTINGS |
| 122 | SECTION 1203 JOINTS AND CONNECTIONS |
| 123 | SECTION 1204 PIPE INSULATION TABLE 1204.2 INSULATION THICKNESS FOR NOMINAL PIPE DIAMETERS |
| 124 | SECTION 1205 VALVES SECTION 1206 PIPING INSTALLATION SECTION 1207 TRANSFER FLUID |
| 125 | SECTION 1208 TESTS SECTION 1209 EMBEDDED PIPING |
| 127 | CHAPTER 13 FUEL OIL PIPING AND STORAGE SECTION 1301 GENERAL SECTION 1302 MATERIAL TABLE 1302.3 FUEL OIL PIPING SECTION 1303 JOINTS AND CONNECTIONS |
| 128 | SECTION 1304 PIPING SUPPORT SECTION 1305 FUEL OIL SYSTEM INSTALLATION |
| 129 | SECTION 1306 OIL GAUGING SECTION 1307 FUEL OIL VALVES SECTION 1308 TESTING |
| 131 | CHAPTER 14 SOLAR SYSTEMS SECTION 1401 GENERAL SECTION 1402 INSTALLATION SECTION 1403 HEAT TRANSFER FLUIDS |
| 132 | SECTION 1404 MATERIALS |
| 133 | CHAPTER 15 REFERENCED STANDARDS ACCA ANSI ARI ASHRAE ASME |
| 134 | ASSE ASTM |
| 135 | AWS |
| 136 | CSA DOL FS ICC |
| 137 | IIAR MSS NAIMA NFPA |
| 138 | SMACNA UL |
| 141 | CHAPTER 16 INSTALLATION AND TESTING OF OIL OR LIQUID FUEL-FIRED EQUIPMENT SECTION 1601 GENERAL SECTION 1602 EQUIPMENT PLACEMENT SECTION 1603 PILOT OPERATION SECTION 1604 BURNER OPERATION SECTION 1605 TEST METHODS |
| 143 | SECTION 1606 EQUIPMENT |
| 145 | APPENDIX A COMBUSTION AIR OPENINGS AND CHIMNEY CONNECTOR PASS-THROUGHS FIGURE A-1 ALL AIR FROM INSIDE THE BUILDING FIGURE A-2 ALL AIR FROM OUTDOORS—INLET AIR FROM VENTILATED CRAWL SPACE AND OUTLET AIR TO VENTILATED ATTIC |
| 146 | FIGURE A-3 ALL AIR FROM OUTDOORS THROUGH VENTILATED ATTIC FIGURE A-4 ALL AIR FROM OUTDOORS THROUGH HORIZONTAL DUCTS OR DIRECT OPENINGS |
| 147 | FIGURE A-5 CHIMNEY CONNECTOR SYSTEMS |
| 148 | FIGURE A-5—continued CHIMNEY CONNECTOR SYSTEMS |
| 149 | APPENDIX B RECOMMENDED PERMIT FEE SCHEDULE B101 MECHANICAL WORK, OTHER THAN GAS PIPING SYSTEMS B102 FEE FOR REINSPECTION B103 TEMPORARY OPERATION INSPECTION FEE B104 SELF-CONTAINED UNITS LESS THAN 2 TONS |
| 151 | INDEX |
| 155 | 2009 MINNESOTA FUEL GAS CODE 2009 MINNESOTA FUEL GAS CODE PREFACE |
| 157 | TABLE OF CONTENTS MINNESOTA FUEL GAS CODE |
| 159 | MINNESOTA RULES CHAPTER 1346 MINNESOTA FUEL GAS CODE 1346.5050 INCORPORATION BY REFERENCE |
| 161 | CHAPTER 1 ADMINISTRATION SECTION 101 (IFGC) GENERAL SECTION 102 (IFGC) APPLICABILITY |
| 162 | SECTION 103 (IFGC) DEPARTMENT OF INSPECTION SECTION 104 (IFGC) DUTIES AND POWERS OF THE CODE OFFICIAL |
| 163 | SECTION 105 (IFGC) APPROVAL SECTION 106 (IFGC) PERMITS |
| 165 | SECTION 107 (IFGC) INSPECTIONS AND TESTING SECTION 108 (IFGC) VIOLATIONS |
| 166 | SECTION 109 (IFGC) MEANS OF APPEAL |
| 169 | CHAPTER 2 DEFINITIONS SECTION 201 (IFGC) GENERAL SECTION 202 (IFGC) GENERAL DEFINITIONS |
| 177 | CHAPTER 3 GENERAL REGULATIONS SECTION 301 (IFGC) GENERAL |
| 178 | SECTION 302 (IFGC) STRUCTURAL SAFETY SECTION 303 (IFGC) APPLIANCE LOCATION |
| 179 | SECTION 304 (IFGC) COMBUSTION, VENTILATION AND DILUTION AIR EQUATION 3-1 EQUATION 3-2 |
| 180 | FIGURE 304.5.3 ALL AIR FROM INSIDE THE BUILDING (see Section 304.5.3) FIGURE 304.6.1(1) ALL AIR FROM OUTDOORS—INLET AIR FROM VENTILATED CRAWL SPACE AND OUTLET AIR TO VENTILATED ATTIC (see Section 304.6.1) FIGURE 304.6.1(2) ALL AIR FROM OUTDOORS THROUGH VENTILATED ATTIC (see Section 304.6.1) |
| 181 | FIGURE 304.6.1(3) ALL AIR FROM OUTDOORS (see Section 304.6.1) |
| 182 | SECTION 305 (IFGC) INSTALLATION |
| 183 | SECTION 306 (IFGC) ACCESS AND SERVICE SPACE |
| 184 | SECTION 307 (IFGC) CONDENSATE DISPOSAL SECTION 308 (IFGS) CLEARANCE REDUCTION |
| 185 | TABLE 308.2 REDUCTION OF CLEARANCES WITH SPECIFIED FORMS OF PROTECTION |
| 186 | FIGURE 308.2(1) EXTENT OF PROTECTION NECESSARY TO REDUCE CLEARANCES FROM APPLIANCE OR VENT CONNECTIONS FIGURE 308.2(2) WALL PROTECTOR CLEARANCE REDUCTION SYSTEM FIGURE 308.2(3) MASONRY CLEARANCE REDUCTION SYSTEM |
| 187 | SECTION 309 (IFGC) ELECTRICAL SECTION 310 (IFGS) ELECTRICAL BONDING |
| 189 | CHAPTER 4 GAS PIPING INSTALLATIONS SECTION 401 (IFGC) GENERAL SECTION 402 (IFGS) PIPE SIZING TABLE 402.2 APPROXIMATE GAS INPUT FOR TYPICAL APPLIANCES |
| 190 | EQUATION 4-1 EQUATION 4-2 TABLE 402.4 Cr AND Y VALUES FOR NATURAL GAS AND UNDILUTED PROPANE AT STANDARD CONDITIONS |
| 191 | TABLE 402.4(1) SCHEDULE 40 METALLIC PIPE |
| 192 | TABLE 402.4(2) SCHEDULE 40 METALLIC PIPE |
| 193 | TABLE 402.4(2)A PIPE SIZING TABLE FOR NATURAL GAS SCHEDULE 40 METALLIC PIPE |
| 194 | TABLE 402.4(3) SCHEDULE 40 METALLIC PIPE |
| 195 | TABLE 402.4(4) SCHEDULE 40 METALLIC PIPE |
| 196 | TABLE 402.4(5) SCHEDULE 40 METALLIC PIPE |
| 197 | TABLE 402.4(6) SEMIRIGID COPPER TUBING |
| 198 | TABLE 402.4(7) SEMIRIGID COPPER TUBING |
| 199 | TABLE 402.4(8) SEMIRIGID COPPER TUBING |
| 200 | TABLE 402.4(9) SEMIRIGID COPPER TUBING |
| 201 | TABLE 402.4(10) SEMIRIGID COPPER TUBING |
| 202 | TABLE 402.4(11) SEMIRIGID COPPER TUBING |
| 203 | TABLE 402.4(12) SEMIRIGID COPPER TUBING |
| 204 | TABLE 402.4(13) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 205 | TABLE 402.4(14) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 206 | TABLE 402.4(15) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 207 | TABLE 402.4(16) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 208 | TABLE 402.4(17) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 209 | TABLE 402.4(18) POLYETHYLENE PLASTIC PIPE |
| 210 | TABLE 402.4(19) POLYETHYLENE PLASTIC PIPE |
| 211 | TABLE 402.4(20) POLYETHYLENE PLASTIC PIPE |
| 212 | TABLE 402.4(21) POLYETHYLENE PLASTIC TUBING TABLE 402.4(22) POLYETHYLENE PLASTIC TUBING |
| 213 | TABLE 402.4(23) SCHEDULE 40 METALLIC PIPE |
| 214 | TABLE 402.4(24) SCHEDULE 40 METALLIC PIPE |
| 215 | TABLE 402.4(25) SCHEDULE 40 METALLIC PIPE |
| 216 | TABLE 402.4(26) SCHEDULE 40 METALLIC PIPE |
| 217 | TABLE 402.4(27) SEMIRIGID COPPER TUBING |
| 218 | TABLE 402.4(28) SEMIRIGID COPPER TUBING |
| 219 | TABLE 402.4(29) SEMIRIGID COPPER TUBING |
| 220 | TABLE 402.4(30) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 221 | TABLE 402.4(31) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 222 | TABLE 402.4(32) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 223 | TABLE 402.4(33) POLYETHYLENE PLASTIC PIPE |
| 224 | TABLE 402.4(34) POLYETHYLENE PLASTIC PIPE |
| 225 | TABLE 402.4(35) POLYETHYLENE PLASTIC TUBING SECTION 403 (IFGS) PIPING MATERIALS |
| 226 | TABLE 403.9.2 SPECIFICATIONS FOR THREADING METALLIC PIPE |
| 227 | SECTION 404 (IFGC) PIPING SYSTEM INSTALLATION |
| 228 | SECTION 405 (IFGS) PIPING BENDS AND CHANGES IN DIRECTION |
| 229 | SECTION 406 (IFGS) INSPECTION, TESTING AND PURGING |
| 230 | TABLE 406.7.1 LENGTH OF PIPING REQUIRING PURGING WITH INERT GAS FOR SERVICING OR MODIFICATION TABLE 406.7.2 LENGTH OF PIPING REQUIRING PURGING WITH INERT GAS BEFORE PLACING IN OPERATION |
| 231 | SECTION 407 (IFGC) PIPING SUPPORT SECTION 408 (IFGC) DRIPS AND SLOPED PIPING SECTION 409 (IFGC) SHUTOFF VALVES TABLE 409.1.1 MANUAL GAS VALVE STANDARDS |
| 232 | SECTION 410 (IFGC) FLOW CONTROLS SECTION 411 (IFGC) APPLIANCE AND MANUFACTURED HOME CONNECTIONS |
| 233 | SECTION 412 (IFGC) LIQUEFIED PETROLEUM GAS MOTOR VEHICLE FUEL-DISPENSING FACILITIES |
| 234 | SECTION 413 (IFGC) COMPRESSED NATURAL GAS MOTOR VEHICLE FUEL-DISPENSING FACILITIES |
| 236 | [F] TABLE 413.9.2.3 SEPARATION DISTANCE FOR ATMOSPHERIC VENTING OF CNG SECTION 414 (IFGC) SUPPLEMENTAL AND STANDBY GAS SUPPLY SECTION 415 (IFGS) PIPING SUPPORT INTERVALS TABLE 415.1 SUPPORT OF PIPING SECTION 416 (IFGS) OVERPRESSURE PROTECTION DEVICES |
| 239 | CHAPTER 5 CHIMNEYS AND VENTS SECTION 501 (IFGC) GENERAL |
| 240 | SECTION 502 (IFGC) VENTS |
| 241 | SECTION 503 (IFGS) VENTING OF APPLIANCES |
| 242 | TABLE 503.4 TYPE OF VENTING SYSTEM TO BE USED |
| 243 | FIGURE 503.5.4 TYPICAL TERMINATION LOCATIONS FOR CHIMNEYS AND SINGLE-WALL METAL PIPES SERVING RESIDENTIAL-TYPE AND LOW-HEAT EQUIPMENT |
| 245 | FIGURE 503.6.4 TERMINATION LOCATIONS FOR GAS VENTS WITH LISTED CAPS 12 INCHES OR LESS IN SIZE AT LEAST 8 FEET FROM A VERTICAL WALL FIGURE 503.6.10.1 PLAN VIEW OF PRACTICAL SEPARATION METHOD FOR MULTISTORY GAS VENTING |
| 247 | TABLE 503.7.7a CLEARANCES FOR CONNECTORS |
| 248 | TABLE 503.10.2.4 MINIMUM THICKNESS FOR GALVANIZED STEEL VENT CONNECTORS FOR LOW-HEAT APPLIANCES TABLE 503.10.2.5 MINIMUM THICKNESS FOR STEEL VENT CONNECTORS FOR MEDIUM-HEAT APPLIANCES AND COMMERCIAL AND INDUSTRIAL INCINERATORS VENT CONNECTOR SIZE |
| 250 | SECTION 504 (IFGS) SIZING OF CATEGORY I APPLIANCE VENTING SYSTEMS |
| 252 | TABLE 504.2(1) TYPE B DOUBLE-WALL GAS VENT |
| 253 | TABLE 504.2(1)—continued TYPE B DOUBLE-WALL GAS VENT |
| 254 | TABLE 504.2(1)—continued TYPE B DOUBLE-WALL GAS VENT |
| 255 | TABLE 504.2(1)—continued TYPE B DOUBLE-WALL GAS VENT |
| 256 | TABLE 504.2(2) TYPE B DOUBLE-WALL GAS VENT |
| 257 | TABLE 504.2(2)—continued TYPE B DOUBLE-WALL GAS VENT |
| 258 | TABLE 504.2(3) MASONRY CHIMNEY |
| 259 | TABLE 504.2(3)—continued MASONRY CHIMNEY |
| 260 | TABLE 504.2(4) MASONRY CHIMNEY |
| 261 | TABLE 504.2(4)—continued MASONRY CHIMNEY |
| 262 | TABLE 504.2(5) SINGLE-WALL METAL PIPE OR TYPE B ASBESTOS CEMENT VENT |
| 263 | TABLE 504.2(6) EXTERIOR MASONRY CHIMNEY |
| 265 | TABLE 504.3.2 MAXIMUM VENT CONNECTOR LENGTH |
| 267 | SECTION 505 (IFGC) DIRECT-VENT, INTEGRAL VENT, MECHANICAL VENT AND VENTILATION/EXHAUST HOOD VENTING SECTION 506 (IFGC) FACTORY-BUILT CHIMNEYS |
| 268 | TABLE 504.3(1) TYPE B DOUBLE-WALL VENT |
| 269 | TABLE 504.3(1)—continued TYPE B DOUBLE-WALL VENT |
| 270 | TABLE 504.3(2) TYPE B DOUBLE-WALL VENT |
| 271 | TABLE 504.3(3) MASONRY CHIMNEY |
| 272 | TABLE 504.3(4) MASONRY CHIMNEY |
| 273 | TABLE 504.3(5) SINGLE-WALL METAL PIPE OR TYPE ASBESTOS CEMENT VENT |
| 274 | TABLE 504.3(6a) EXTERIOR MASONRY CHIMNEY TABLE 504.3(6b) EXTERIOR MASONRY CHIMNEY TABLE 504.3(6b) EXTERIOR MASONRY CHIMNEY—continued |
| 275 | TABLE 504.3(7a) EXTERIOR MASONRY CHIMNEY TABLE 504.3(7b) EXTERIOR MASONRY CHIMNEY TABLE 504.3(7b) EXTERIOR MASONRY CHIMNEY—continued |
| 277 | CHAPTER 6 SPECIFIC APPLIANCES SECTION 601 (IFGC) GENERAL SECTION 602 (IFGC) DECORATIVE APPLIANCES FOR INSTALLATION IN FIREPLACES SECTION 603 (IFGC) LOG LIGHTERS SECTION 604 (IFGC) VENTED GAS FIREPLACES (DECORATIVE APPLIANCES) SECTION 605 (IFGC) VENTED GAS FIREPLACE HEATERS SECTION 606 (IFGC) INCINERATORS AND CREMATORIES SECTION 607 (IFGC) COMMERCIAL-INDUSTRIAL INCINERATORS SECTION 608 (IFGC) VENTED WALL FURNACES |
| 278 | SECTION 609 (IFGC) FLOOR FURNACES SECTION 610 (IFGC) DUCT FURNACES SECTION 611 (IFGC) NONRECIRCULATING DIRECT-FIRED INDUSTRIAL AIR HEATERS |
| 279 | SECTION 612 (IFGC) RECIRCULATING DIRECT-FIRED INDUSTRIAL AIR HEATERS SECTION 613 (IFGC) CLOTHES DRYERS SECTION 614 (IFGC) CLOTHES DRYER EXHAUST |
| 280 | SECTION 615 (IFGC) SAUNA HEATERS |
| 281 | SECTION 616 (IFGC) ENGINE AND GAS TURBINE- POWERED EQUIPMENT SECTION 617 (IFGC) POOL AND SPA HEATERS SECTION 618 (IFGC) FORCED-AIR WARM-AIR FURNACES SECTION 619 (IFGC) CONVERSION BURNERS |
| 282 | SECTION 620 (IFGC) UNIT HEATERS SECTION 621 (IFGC) UNVENTED ROOM HEATERS SECTION 622 (IFGC) VENTED ROOM HEATERS SECTION 623 (IFGC) COOKING APPLIANCES SECTION 624 (IFGC) WATER HEATERS SECTION 625 (IFGC) REFRIGERATORS |
| 283 | SECTION 626 (IFGC) GAS-FIRED TOILETS SECTION 627 (IFGC) AIR-CONDITIONING EQUIPMENT SECTION 628 (IFGC) ILLUMINATING APPLIANCES |
| 284 | SECTION 629 (IFGC) SMALL CERAMIC KILNS SECTION 630 (IFGC) INFRARED RADIANT HEATERS SECTION 631 (IFGC) BOILERS SECTION 632 (IFGC) EQUIPMENT INSTALLED IN EXISTING UNLISTED BOILERS SECTION 633 (IFGC) STATIONARY FUEL-CELL POWER SYSTEMS |
| 285 | SECTION 634 (IFGS) CHIMNEY DAMPER OPENING AREA TABLE 634.1 FREE OPENING AREA OF CHIMNEY DAMPER FOR VENTING FLUE GASES FROM UNLISTED DECORATIVE APPLIANCES FOR INSTALLATION IN VENTED FIREPLACES SECTION 635 (IFGC) GASEOUS HYDROGEN SYSTEMS |
| 287 | CHAPTER 7 GASEOUS HYDROGEN SYSTEMS SECTION 701 (IFGC) GENERAL SECTION 702 (IFGC) GENERAL DEFINITIONS SECTION 703 (IFGC) GENERAL REQUIREMENTS |
| 288 | SECTION 704 (IFGC) PIPING, USE AND HANDLING |
| 289 | SECTION 705 (IFGC) TESTING OF HYDROGEN PIPING SYSTEMS |
| 290 | SECTION 706 (IFGC) LOCATION OF GASEOUS HYDROGEN SYSTEMS |
| 291 | SECTION 707 (IFGC) OPERATION AND MAINTENANCE OF GASEOUS HYDROGEN SYSTEMS SECTION 708 (IFGC) DESIGN OF LIQUEFIED HYDROGEN SYSTEMS ASSOCIATED WITH HYDROGEN VAPORIZATION OPERATIONS |
| 293 | IFGC/IFGS CHAPTER 8 REFERENCED STANDARDS ANSI |
| 294 | ASME ASTM CGA CSA |
| 295 | DOTn ICC MSS NFPA |
| 296 | UL |
| 297 | CHAPTER 9 INSTALLATION AND TESTING OF FUEL GAS-FIRED EQUIPMENT SECTION 901 (IFGC) GENERAL SECTION 902 (IFGC) EQUIPMENT PLACEMENT SECTION 903 (IFGC) PILOT OPERATION SECTION 904 (IFGC) BURNER OPERATION |
| 298 | SECTION 905 (IFGC) METHOD OF TEST |
| 299 | SECTION 906 (IFGC) PRESSURE REGULATORS SECTION 907 (IFGC) EQUIPMENT INFORMATION |
| 301 | CHAPTER 10 MANUFACTURED HOME PARK/COMMUNITY FUEL GAS EQUIPMENT AND INSTALLATION SECTION 1000 GENERAL TABLE 1002 DEMAND FACTORS FOR CALCULATING GAS PIPING SYSTEMS IN MANUFACTURED HOME PARKS AND COMMUNITIES |
| 303 | APPENDIX A (IFGS) SIZING AND CAPACITIES OF GAS PIPING |
| 304 | TABLE A.2.2 EQUIVALENT LENGTHS OF PIPE FITTINGS AND VALVES |
| 305 | TABLE A.2.2—continued EQUIVALENT LENGTHS OF PIPE FITTINGS AND VALVES |
| 306 | TABLE A.2.4 MULTIPLIERS TO BE USED WITH TABLES 402.4(1) THROUGH 402.4(22) WHERE THE SPECIFIC GRAVITY OF THE GAS IS OTHER THAN 0.60 |
| 308 | TABLE A.3.4 THOUSANDS OF Btu/h (MBH) OF NATURAL GAS PER 100 FEET OF PIPE AT VARIOUS PRESSURE DROPS AND PIPE DIAMETERS |
| 309 | TABLE A.5.1 SCHEDULE 40 STEEL PIPE STANDARD SIZES TABLE A.5.2 COPPER TUBE STANDARD SIZES |
| 310 | FIGURE A.6 (a) CAPACITY OF NATURAL GAS PIPING, LOW PRESSURE (LESS THAN 1.5 PSI) FIGURE A.6 (b) CAPACITY OF NATURAL GAS PIPING, HIGH PRESSURE (1.5 psi and above) |
| 311 | FIGURE A.7.1 PIPING PLAN SHOWING A STEEL PIPING SYSTEM |
| 312 | FIGURE A.7.2 PIPING PLAN SHOWING A CSST SYSTEM FIGURE A.7.3 PIPING PLAN SHOWING A COPPER TUBING SYSTEM |
| 313 | FIGURE A.7.4 PIPING PLAN SHOWING A MODIFICATION TO EXISTING PIPING SYSTEM |
| 315 | APPENDIX B (IFGS) SIZING OF VENTING SYSTEMS SERVING APPLIANCES EQUIPPED WITH DRAFT HOODS, CATEGORY I APPLIANCES, AND APPLIANCES LISTED FOR USE WITH TYPE B VENTS FIGURE B-1 TYPE B DOUBLE-WALL VENT SYSTEM SERVING A SINGLE APPLIANCE WITH A TYPE B DOUBLE-WALL VENT FIGURE B-2 TYPE B DOUBLE-WALL VENT SYSTEM SERVING A SINGLE APPLIANCE WITH A SINGLE-WALL METAL VENT CONNECTOR |
| 316 | FIGURE B-3 VENT SYSTEM SERVING A SINGLE APPLIANCE WITH A MASONRY CHIMNEY OF TYPE B DOUBLE-WALL VENT CONNECTOR FIGURE B-4 VENT SYSTEM SERVING A SINGLE APPLIANCE USING A MASONRY CHIMNEY AND A SINGLE-WALL METAL VENT CONNECTOR FIGURE B-5 ASBESTOS CEMENT TYPE B OR SINGLE-WALL METAL VENT SYSTEM SERVING A SINGLE DRAFT-HOOD-EQUIPPED APPLIANCE FIGURE B-6 VENT SYSTEM SERVING TWO OR MORE APPLIANCES WITH TYPE B DOUBLE-WALL VENT AND TYPE B DOUBLE-WALL VENT CONNECTOR |
| 317 | FIGURE B-7 VENT SYSTEM SERVING TWO OR MORE APPLIANCES WITH TYPE B DOUBLE-WALL VENT AND SINGLE-WALL METAL VENT CONNECTORS FIGURE B-8 MASONRY CHIMNEY SERVING TWO OR MORE APPLIANCES WITH TYPE B DOUBLE-WALL VENT CONNECTOR FIGURE B-9 MASONRY CHIMNEY SERVING TWO OR MORE APPLIANCES WITH SINGLE-WALL METAL VENT CONNECTORS FIGURE B-10 ASBESTOS CEMENT TYPE B OR SINGLE-WALL METAL VENT SYSTEM SERVING TWO OR MORE DRAFT-HOOD-EQUIPPED APPLIANCES |
| 318 | FIGURE B-13 MULTISTORY GAS VENT DESIGN PROCEDURE FOR EACH SEGMENT OF SYSTEM FIGURE B-14 MULTISTORY VENT SYSTEMS |
| 319 | FIGURE B-15 (EXAMPLE 1) SINGLE DRAFT-HOOD-EQUIPPED APPLIANCE FIGURE B-16 (EXAMPLE 2) SINGLE FAN-ASSISTED APPLIANCE |
| 320 | FIGURE B-17 (EXAMPLE 4) COMMON VENTING TWO DRAFT-HOOD-EQUIPPED APPLIANCES FIGURE B-18 (EXAMPLE 5A) COMMON VENTING A DRAFT HOOD WITH A FAN-ASSISTED FURNACE INTO A TYPE B DOUBLE-WALL COMMON VENT |
| 322 | TABLE B-1 MASONRY CHIMNEY LINER DIMENSIONS WITH CIRCULAR EQUIVALENTSa |
| 323 | FIGURE B-19 |
| 325 | APPENDIX C (IFGS) EXIT TERMINALS OF MECHANICAL DRAFT AND DIRECT-VENT VENTING SYSTEMS APPENDIX C EXIT TERMINALS OF MECHANICAL DRAFT AND DIRECT-VENT VENTING SYSTEMS |
| 326 | TABLE C-1 RECOMMENDED CAPACITIES FOR DOMESTIC KITCHEN EXHAUST HOODS |
| 327 | APPENDIX D (IFGS) RECOMMENDED PROCEDURE FOR SAFETY INSPECTION OF AN EXISTING APPLIANCE INSTALLATION |
| 329 | IFGC APPENDIX E (IFGC) WORKSHEET E-1 RESIDENTIAL COMBUSTION AIR CALCULATION METHOD WORKSHEET E-1 RESIDENTIAL COMBUSTION AIR CALCULATION METHOD (For Furnace, Boiler, and/or Water Heater in the Same Space) |
| 330 | TABLE E-1 RESIDENTIAL COMBUSTION AIR REQUIRED VOLUME (Requ ired Interior Volume Based on Input Rating of Appliances) |
| 331 | TABLE E1 RESIDENTIAL COMBUSTION AIR REQUIRED VOLUME—Continued (Required Interior Volume Based on Input Rating of Appliances) |
| 333 | INDEX |
| 337 | 2009 MINNESOTA PLUMBING CODE TABLE OF CONTENTS MINNESOTA PLUMBING CODE |
| 341 | MINNESOTA RULES, CHAPTER 4715 2009 MINNESOTA PLUMBING CODE 4715.0100 DEFINITIONS |
| 342 | FIGURE – BAROMETRIC LOOP FIGURE – BRANCH INTERVAL |
| 343 | FIGURE – COMMON VENTS FIGURE – CONTINUOUS WASTE |
| 344 | FIGURE – COMMON VENT (BACK TO BACK WATER CLOSETS) FIGURE – INDIVIDUAL VENTS (BACK TO BACK WATER CLOSETS) |
| 345 | FIGURE – FIXTURE BRANCH DRAIN/BUILDING DRAIN BRANCH |
| 348 | 4715.0200 BASIC PLUMBING PRINCIPLES |
| 349 | 4715.0300 GENERAL REGULATIONS OF PLUMBING CONSTRUCTION 4715.0310 USE OF PUBLIC SEWER AND WATER SYSTEMS REQUIRED 4715.0320 CONFORMANCE WITH CODE 4715.0330 ALTERNATE FIXTURES, APPURTENANCES, MATERIALS, AND METHODS |
| 350 | 4715.0340 HEALTH AND SAFETY 4715.0400 QUALITY OF MATERIALS 4715.0410 IDENTIFICATION OF MATERIALS 4715.0420 STANDARDS FOR PLUMBING MATERIALS |
| 351 | TABLE STANDARDS FOR PLUMBING MATERIALS |
| 352 | TABLE STANDARDS FOR PLUMBING MATERIALS-continued |
| 353 | TABLE STANDARDS FOR PLUMBING MATERIALS-continued |
| 354 | 4715.0500 WATER SUPPLY SYSTEMS 4715.0510 WATER SERVICE PIPE 4715.0520 WATER DISTRIBUTION PIPE 4715.0530 BUILDING SEWERS |
| 355 | 4715.0540 STORM WATER AND YARD DRAINAGE (OUTSIDE FOUNDATION WALLS) 4715.0550 STORM WATER OR CLEAR WATER DRAINAGE (WITHIN BUILDINGS UNDERGROUND) 4715.0560 STORM WATER OR CLEAR WATER DRAINAGE (WITHIN BUILDINGS ABOVE GROUND) 4715.0570 SOIL AND WASTE PIPING UNDERGROUND OR EMBEDDED 4715.0580 SOIL AND WASTE PIPING ABOVE GROUND 4715.0590 VENT PIPING BELOW GROUND |
| 356 | 4715.0600 VENT PIPING ABOVE GROUND 4715.0610 SPECIAL WASTES 4715.0620 SUBSOIL DRAINS 4715.0630 SPECIAL MATERIALS 4715.0640 FIXTURE MATERIALS |
| 357 | 4715.0700 TIGHTNESS 4715.0710 ASBESTOS CEMENT SEWER PIPE JOINTS 4715.0720 BITUMINIZED FIBER DRAIN PIPE JOINT 4715.0730 BURNED LEAD JOINTS 4715.0740 CAULKED JOINTS 4715.0750 CEMENT MORTAR JOINTS 4715.0760 COLD JOINT COMPOUND, TAR BASE 4715.0770 FLARED JOINTS 4715.0780 GASKET TYPE JOINTS 4715.0790 HOT-POURED JOINTS |
| 358 | 4715.0800 MECHANICAL JOINTS 4715.0805 PUSH-ON JOINTS 4715.0810 PLASTIC JOINTS |
| 359 | 4715.0815 JOINTS IN CHEMICAL WASTE PIPE 4715.0820 SOLDERED OR BRAZED JOINTS 4715.0830 THREADED JOINTS — SCREWED JOINTS 4715.0840 WIPED JOINTS 4715.0850 USE OF JOINTS |
| 360 | 4715.0860 SPECIAL JOINTS 4715.0870 FLANGED FIXTURE CONNECTIONS 4715.0880 PROHIBITED JOINTS AND CONNECTIONS 4715.0890 INCREASERS AND REDUCERS |
| 361 | 4715.0900 FIXTURE TRAP REQUIREMENTS FIGURE – 4715.0900 FIXTURE TRAP REQUIREMENTS 4715.0910 TRAPS DESCRIBED 4715.0920 TRAP PROTECTION 4715.0930 SIZES OF TRAPS 4715.0940 SLIP JOINTS AND UNIONS 4715.0950 TRAP SEALS |
| 362 | FIGURE – 4715.0950 TRAP SEALS 4715.0960 TRAPS PROHIBITED 4715.0970 TRAP CLEANOUTS |
| 363 | 4715.1000 LOCATION 4715.1010 SIZE OF CLEANOUTS 4715.1020 CLEANOUT MATERIALS 4715.1030 CLEANOUTS TO BE ACCESSIBLE |
| 364 | 4715.1100 INTERCEPTORS AND SEPARATORS REQUIRED 4715.1110 GREASE INTERCEPTORS FOR COMMERCIAL BUILDINGS FIGURE – 4715.1110 GREASE INTERCEPTORS FOR COMMERCIAL BUILDINGS 4715.1115 EXTERIOR GREASE INTERCEPTORS |
| 365 | 4715.1120 OIL AND FLAMMABLE LIQUIDS SEPARATOR 4715.1130 INTERCEPTORS AND SEPARATORS FOR SPECIFIC INSTALLATIONS |
| 366 | FIGURE – 4715.1120 OIL AND FLAMMABLE LIQUIDS SEPARATOR 4715.1140 VENTING OF INTERCEPTORS AND SEPARATORS 4715.1150 MAINTENANCE OF INTERCEPTORS AND SEPARATORS 4715.1160 BACKWATER VALVES |
| 367 | 4715.1200 CONNECTIONS TO PLUMBING SYSTEM REQUIRED 4715.1210 REQUIRED MINIMUM NUMBER OF FIXTURES 4715.1220 INSTALLATION OF FIXTURES 4715.1230 AUTOMATIC CLOTHES WASHERS 4715.1240 BATHTUBS 4715.1250 DISHWASHING EQUIPMENT 4715.1260 DRINKING FOUNTAINS |
| 368 | FIGURE – 4715.1250 DISHWASHING EQUIPMENT 4715.1300 FLOOR DRAINS |
| 369 | FIGURE – 4715.1300 FLOOR DRAINS (Subp. 4) 4715.1305 ELEVATOR PIT DRAIN 4715.1310 FOOD-WASTE GRINDER UNITS 4715.1320 FLUSHING DEVICES FOR WATER CLOSETS AND URINALS 4715.1330 FLUSH TANKS |
| 370 | 4715.1340 FLUSHOMETER VALVES 4715.1350 GARBAGE CAN WASHERS 4715.1360 LAUNDRY TRAYS 4715.1370 LAVATORIES 4715.1380 SHOWERS 4715.1390 SINKS |
| 371 | 4715.1400 SPECIAL PLUMBING FIXTURES 4715.1410 URINALS 4715.1420 WATER CLOSETS 4715.1430 HANGERS AND SUPPORTS 4715.1440 PROTECTION OF PLASTIC PIPE |
| 372 | 4715.1500 INDIRECT WASTE CONNECTIONS 4715.1510 INDIRECT WASTE PIPING 4715.1520 CONNECTIONS FROM WATER DISTRIBUTION SYSTEM 4715.1530 STERILIZERS 4715.1540 POTABLE CLEAR WATER WASTES 4715.1550 DRINKING FOUNTAINS 4715.1560 SWIMMING POOLS 4715.1570 METHOD OF PROVIDING AN AIR GAP 4715.1580 METHOD OF PROVIDING AN AIR BREAK 4715.1590 RECEPTORS OR SUMPS |
| 373 | FIGURE – 4715.1570 METHOD OF PROVIDING AN AIR GAP FIGURE 4715.1580 METHOD OF PROVIDING AN AIR BREAK |
| 374 | 4715.1600 CHEMICAL WASTES 4715.1610 STEAM AND HOT WATER WASTES |
| 375 | 4715.1700 WATER REQUIRED 4715.1710 WATER SERVICE 4715.1720 DESIGN OF BUILDING WATER DISTRIBUTION SYSTEM 4715.1730 SIZE OF FIXTURE BRANCH TABLE OF MINIMUM SIZES OF FIXTURE WATER BRANCH LINES |
| 376 | 4715.1740 WATER PRESSURE 4715.1750 WATER HAMMER 4715.1760 SUPPLY DEMAND 4715.1770 MINIMUM PRESSURES REQUIRED IN WATER DISTRIBUTION SYSTEM TABLE OF MINIMUM FLOW PRESSURE AND FLOW RATES |
| 377 | 4715.1800 WATER SUPPLY CONTROL VALVES 4715.1810 WATER PRESSURE BOOSTER SYSTEMS |
| 378 | TABLE – SIZES FOR OVERFLOW PIPES FOR WATER SUPPLY TANKS TABLE – SIZE OF DRAIN PIPES FOR WATER TANKS |
| 379 | 4715.1900 DESIGN, MAINTENANCE, AND INSTALLATION 4715.1910 IDENTIFICATION OF POTABLE AND NONPOTABLE WATER 4715.1911 TOXIC MATERIALS AND USED PIPE 4715.1912 USED WATER RETURN PROHIBITED 4715.1920 CROSS-CONNECTION CONTROL 4715.1930 [RENUMBERED 4715.1911] 4715.1940 POTABLE WATER CONNECTIONS TO HEATING OR COOLING SYSTEMS 4715.1941 HEAT EXCHANGERS |
| 380 | 4715.1950 PROHIBITED CONNECTIONS TO FIXTURES AND EQUIPMENT 4715.1960 REFRIGERATING UNIT CONDENSERS AND COOLING JACKETS 4715.1970 [RENUMBERED 4715.1912] |
| 381 | 4715.2000 WATER OUTLETS 4715.2010 MINIMUM REQUIRED AIR GAP TABLE – MINIMUM AIR GAPS FOR PLUMBING FIXTURES FIGURE – 4715.2010 MINIMUM REQUIRED AIR GAP |
| 382 | 4715.2020 DEVICES OR ASSEMBLIES FOR THE PROTECTION OF THE POTABLE WATER SUPPLY 4715.2030 APPROVAL OF DEVICES OR ASSEMBLIES |
| 383 | 4715.2100 BACKFLOW PREVENTERS 4715.2110 TYPES OF DEVICES REQUIRED WHERE AN AIR GAP CANNOT BE PROVIDED TABLE 4715.2110 TYPES OF DEVICES REQUIRED WHERE AN AIR GAP CANNOT BE PROVIDED1 |
| 384 | TABLE 4715.2110—continued TYPES OF DEVICES REQUIRED WHERE AN AIR GAP CANNOT BE PROVIDED 4715.2120 LOCATION OF BACKFLOW PREVENTERS 4715.2130 [REPEALED, 15 SR 76] 4715.2140 [REPEALED, 15 SR 76] 4715.2150 CONNECTIONS NOT SUBJECT TO BACK PRESSURE TABLE – CROSS-CONNECTIONS WHERE PROTECTIVE DEVICES ARE REQUIRED AND CRITICAL LEVEL (C-L) SETTINGS FOR BACKFLOW PREVENTORS 4715.2160 CONNECTIONS SUBJECT TO BACK PRESSURE |
| 385 | 4715.2161 INSTALLATION OF REDUCED PRESSURE BACKFLOW PREVENTERS 4715.2162 DOUBLE CHECK-DOUBLE GATE VALVE ASSEMBLIES 4715.2163 CARBONATED BEVERAGE MACHINES 4715.2165 CHEMICAL/SOAP DISPENSING SYSTEMS 4715.2170 BAROMETRIC LOOP 4715.2180 HOT WATER SUPPLY SYSTEM 4715.2190 COMBINATION WATER AND SPACE HEATING EQUIPMENT |
| 386 | 4715.2200 PRESSURE RELIEF VALVES AND TEMPERATURE RELIEF VALVES DEVICES REQUIRED 4715.2210 PRESSURE RELIEF VALVES 4715.2215 THERMAL EXPANSION CONTROL 4715.2220 HOT WATER STORAGE TANKS 4715.2230 TANKLESS AND INSTANTANEOUS TYPE HEATERS 4715.2240 ACCESS TO WATER HEATERS 4715.2250 DISINFECTION OF POTABLE WATER SYSTEM |
| 387 | 4715.2260 [RENUMBERED 4715.2161] 4715.2270 [RENUMBERED 4715.2162] 4715.2280 WATER METER INSTALLATION |
| 388 | 4715.2300 LOAD ON DRAINAGE PIPING TABLE VALUES FOR INTERMITTENT FLOWS TABLE OF FIXTURE UNITS VALUES TABLE OF FIXTURE UNITS VALUES—Continued |
| 389 | 4715.2310 SELECTING SIZE OF GRAVITY DRAINAGE PIPING TABLE MAXIMUM LOADS FOR HORIZONTAL DRAINS IN FIXTURE UNITS TABLE MAXIMUM LOADS FOR SOIL AND WASTE STACKS IN FIXTURE UNITS 4715.2320 MINIMUM SIZE OF SOIL AND WASTE STACKS 4715.2330 MINIMUM SIZE OF STACK VENT OR VENT STACK 4715.2340 PROVISION FOR FUTURE FIXTURES 4715.2350 MINIMUM SIZE OF UNDERGROUND DRAINAGE PIPING 4715.2360 SIZING OF OFFSETS ON DRAINAGE PIPING |
| 390 | FIGURE 4715.2330 MINIMUM SIZE OF STACK VENT OR VENT STACK FIGURE 4715.2330 MINIMUM SIZE OF STACK VENT OR VENT STACK |
| 391 | FIGURE 4715.2360 SIZING OF OFFSETS ON DRAINAGE PIPING 4715.2370 FIXTURE CONNECTIONS TO AN OFFSET OF MORE THAN 45 DEGREES OR AT BASE OF STACK |
| 392 | 4715.2400 PITCH ON HORIZONTAL DRAINAGE PIPING TABLE SIZE OF PIPING AND MINIMUM SLOPE 4715.2410 CHANGE IN DIRECTION FIGURE 4715.2410 CHANGE IN DIRECTION 4715.2420 PROHIBITED FITTINGS AND CONNECTIONS 4715.2430 DRAINS BELOW BUILDING SEWER |
| 393 | 4715.2440 DESIGN OF SUMPS FIGURE 4715.2440 DESIGN OF SUMPS |
| 394 | 4715.2500 SELECTING SIZE OF VENT PIPING 4715.2510 PROTECTION OF TRAP SEALS 4715.2520 VENT STACKS AND STACK VENTS FIGURE 4715.2520 VENT STACKS AND STACK VENTS |
| 395 | TABLE SIZE AND LENGTH OF VENT STACKS TABLE SIZE AND LENGTH OF VENTS; INDIVIDUAL, BRANCH, CIRCUIT AND HEADER FIGURE 4715.2520 VENT STACKS AND STACK VENTS |
| 396 | FIGURE 4715.2520 VENT STACKS AND STACK VENTS FIGURE 4715.2520 VENT STACKS AND STACK VENTS 4715.2530 VENT TERMINALS |
| 397 | 4715.2540 VENT GRADES AND CONNECTIONS FIGURE 4715.2540 VENT GRADES AND CONNECTIONS 4715.2550 WET VENTING 4715.2560 STACK VENTING |
| 398 | FIGURE 4715.2550 WET VENTING FIGURE 4715.2550 WET VENTING 4715.2570 INDIVIDUAL FIXTURE REVENTING REQUIRED 4715.2580 COMMON VENTS |
| 399 | FIGURE 4715.2560 STACK VENTING FIGURE 4715.2580 COMMON VENTS |
| 400 | FIGURE 4715.2580 COMMON VENTS |
| 401 | 4716.2600 CIRCUIT AND LOOP VENTING FIGURE 4716.2600 CIRCUIT AND LOOP VENTING (SUBP.2) |
| 402 | FIGURE 4715.2600 CIRCUIT AND LOOP VENTING (SUBP.3) |
| 403 | 4715.2610 FIXTURES BACK-TO-BACK 4715.2620 FIXTURE VENTS TABLE DISTANCE OF FIXTURE TRAP FROM VENT FIGURE 4715.2620 FIXTURE VENTS FIGURE 4715.2620 FIXTURE VENTS (SUBP. 3) |
| 404 | 4715.2630 VENTS FOR FIXTURE TRAP BELOW TRAP DIP 4715.2640 YOKE VENTS FOR STACKS OF MORE THAN FIVE BRANCH INTERVALS FIGURE 4715.2640 YOKE VENT STACKS OF MORE THAN FIVE BRANCH INTERVALS 4715.2650 COMBINATION WASTE AND VENT SYSTEM FIGURE 4715.2655 ISLAND FIXTURE VENTING |
| 405 | 4715.2650 COMBINATION WASTE AND VENT SYSTEM 4715.2655 ISLAND FIXTURE VENTING 4715.2660 VENTING OF SUMPS AND SEWERS |
| 406 | 4715.2700 STORM SEWER SYSTEMS 4715.2710 SIZE OF BUILDING STORM DRAINS AND LEADERS TABLE HORIZONTAL STORM DRAINS TABLE SIZE OF VERTICAL LEADERS FIGURE 4715.2710 SIZE OF BUILDING STORM DRAINS AND LEADERS 4715.2720 SUBSOIL DRAINS 4715.2730 BUILDING SUBDRAINS |
| 407 | 4715.2740 TRAPS ON STORM DRAINS AND LEADERS 4715.2750 CONDUCTORS AND CONNECTIONS 4715.2760 ROOF AND DECK DRAINS 4715.2770 PROVISIONS FOR EXPANSION 4715.2780 CONTROL FLOW STORM WATER DRAINAGE FOR DEAD LEVEL ROOFS TABLE SIZE OF VERTICAL LEADERS TABLE SIZE OF HORIZONTAL STORM DRAINS |
| 408 | 4715.2800 INSPECTIONS 4715.2810 NOTIFICATIONS 4715.2820 METHOD OF TESTING |
| 409 | FIGURE 4715.2820 METHOD OF TESTING 4715.2830 COVERING OF WORK 4715.2840 DEFECTIVE WORK 4715.2850 AIR TEST OF DEFECTIVE PLUMBING 4715.2860 MAINTENANCE |
| 410 | 4715.2870 DISINFECTION OF WATER PIPING 4715.2880 BUILDING SEWER 4715.2890 CERTIFICATE OF APPROVAL |
| 411 | 4715.3130 PLANS AND SPECIFICATIONS 4715.3500 GENERAL 4715.3600 TOTAL DAILY WATER REQUIREMENTS. TABLE DESIGN CRITERIA FOR DAILY WATER REQUIREMENTSBASED ON BUILDING OCCUPANCY TABLE DESIGN CRITERIA FOR DAILY WATER REQUIREMENTS BASEDON BUILDING OCCUPANCY—CONTINUED |
| 412 | TABLE DAILY WATER REQUIREMENTS FOR COMMON FARM ANIMALS 4715.3700 DETERMINATION OF PEAK DEMAND TABLE SUPPLY FIXTURE UNIT VALUES FOR VARIOUS PLUMBING FIXTURES |
| 413 | TABLE SUPPLY DEMAND FOR VARIOUS LOADSIN SUPPLY FIXTURE UNITS FIGURE GRAPH OF SUPPLY DEMAND FOR VARIOUS LOADS IN SUPPLY FIXTURE UNITS TABLE SUBP. 6 EXAMPLE TABULATION |
| 414 | TABLE SUBP. 7 EXAMPLE TABULATION |
| 415 | TABLE LOSS OF PRESSURE THROUGH DISK-TYPE METERS(pounds per square inch) |
| 416 | FIGURE GRAPH OF LOSS OF PRESSURE THROUGH DISK-TYPE METERS IN POUNDS PER SQUARE INCH TABLE ALLOWANCE IN EQUIVALENT LENGTH OF PIPE FOR FRICTION LOSS IN VALVES AND THREADED FITTINGS TABLE LOSS OF PRESSURE THROUGH TAPS AND TEES IN POUNDS PER SQUARE INCH |
| 417 | TABLE PRESSURE LOSS OF WATER IN POUNDS PER SQUARE INCH PER 100 FEET OF FAIRLY SMOOTH PIPE |
| 418 | FIGURE GRAPH OF PRESSURE LOSS OF WATER IN POUNDS PER SQUARE INCH PER 100 FEET OF FAIRLY SMOOTH PIPE |
| 419 | TABLE PRESSURE LOSS OF WATER IN POUNDS PER SQUARE INCH PER 100 FEET OF FAIRLY ROUGH PIPE |
| 420 | FIGURE GRAPH OF PRESSURE LOSS OF WATER IN POUNDS PER SQUARE INCH PER 100 FEET OF FAIRLY ROUGH PIPE |
| 421 | TABLE PRESSURE LOSS OF WATER IN POUNDS PER SQUARE INCH PER 100 FEET OF ROUGH PIPE |
| 422 | FIGURE PRESSURE LOSS OF WATER IN POUNDS PER SQUARE INCH PER 100 FEET OF ROUGH PIPE |
| 423 | TABLE PRESSURE LOSS OF WATER IN POUNDS PER SQUARE INCH PER 100 FEET OF COPPER PIPE |
| 424 | TABLE PRESSURE LOSS OF WATER IN POUNDS PER SQUARE INCH PER 100 FEET OF COPPER PIPE—continued |
| 425 | FIGURE GRAPH OF PRESSURE LOSS OF WATER IN POUNDS PER SQUARE INCH PER 100 FEET OF COPPER PIPE |
| 426 | FIGURE ILLUSTRATION |
| 427 | TABLE RECOMMENDED TABULAR ARRANGEMENT FOR USE IN SOLVING PIPE SIZING PROBLEMS |
| 428 | 4715.3800 RECOMMENDED GUIDE FOR SIZING WATER SUPPLY SYSTEM FIGURE 4715.3800 RECOMMENDED GUIDE FOR SIZING WATER SUPPLY SYSTEM (Water Closet Flushometers) |
| 429 | TABLE EQUIVALENT FIXTURE UNITS, INCLUDING COMBINED HOT AND COLD WATER DEMAND |
| 430 | TABLE FIXTURE UNIT TABLE FOR DETERMINING WATER PIPE AND METER SIZES FOR WATER SUPPLY SYSTEMS |
| 431 | FIGURE EXAMPLE OF CODE WATER SIZING USING SUBPART. 9 FIGURE EXAMPLE OF HOT WATER SIZING USING SUBPART. 9 |
| 432 | 4715.3900 [REPEALED, 15 SR 76] 4715.4000 [REPEALED, 15 SR 76] 4715.4100 USEFUL INFORMATION TABLE PRESSURE AND HEAD EQUIVALENTS |
| 433 | TABLE DECIMAL EQUIVALENTS OF COMMON FRACTIONS IN INCHES TABLE DECIMAL EQUIVALENTS OF INCHES IN FEET FIGURE GEOMETRIC CALCULATIONS |
| 434 | TABLE DIAMETER, AREA, CIRCUMFERENCE AND VOLUME FIGURE ILLUSTRATION OF MEASUREMENTS |
| 435 | TABLE PIPE FITTING ANGLE CALCULATIONS |
| 436 | 4715.5000 SCOPE AND APPLICABILITY 4715.5100 DEFINITIONS 4715.5200 CONNECTION WITH WATER DISTRIBUTION SYSTEM 4715.5300 EQUIPMENT DRAIN 4715.5400 LOCATION 4715.5500 REGENERATION SANITATION PROCEDURES TABLE MINIMUM CHLORINE RESIDUAL AND TIME COMBINATION |
| 437 | 4715.5600 [REPEALED, L 2007 c 140 art 13 s 3] 4715.5700 EQUIPMENT AND MATERIALS USED IN INSTALLATIONS 4715.5800 LICENSING 4715.5900 [REPEALED, L 2007 c 140 art 13 s 3] 4715.6000 RENEWAL |
| 439 | TABLE OF CONTENTS MISCELLANEOUS MINNESOTA STATUTES RELATED TO PLUMBING |
| 441 | MISCELLANEOUS MINNESOTA STATUTES RELATED TO PLUMBING 326B.41 PURPOSE 326B.42 DEFINITIONS 326B.43 PLUMBING STANDARDS; RULES; AGREEMENT WITH MUNICIPALITY; EXEMPTION |
| 443 | 326B.435 PLUMBING BOARD |
| 446 | 326B.439B AN ON LEAD IN PLUMBING 326B.44 LOCAL REGULATIONS 326B.45 VIOLATIONS TO BE REPORTED TO COMMISSIONER 326B.46 LICENSING, BOND AND INSURANCE |
| 447 | 326B.47 PLUMBER’S APPRENTICES 326B.475 RESTRICTED PLUMBER LICENSE |
| 448 | 326B.48 RECIPROCITY WITH OTHER STATES 326B.49 APPLICATIONS, FEES |
| 449 | TABLE INSPECTION FEES |
