šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
NFPA 286 2024

NFPA 286 2024

$80.71

NFPA 286: Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth

Published By Publication Date Number of Pages
NFPA 2024 29
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

Also known as the “room corner” test, NFPA 286, Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth, provides a method of determining the flammability characteristics of exterior, non-load bearing wall assemblies and panels that are required to be of non-combustible construction but may contain combustible components. Vital for testing laboratories, NFPA 286 addresses all wall coverings, including textile wall coverings. Measurements in the fire test room document the extent of fire growth, rate of heat release, total heat released, time to flashover, time to flame extension, total heat flux incident to the floor, upper level gas temperature, smoke obscuration, production of carbon monoxide, and emissions of other combustion gases.

PDF Catalog

PDF Pages PDF Title
2 Important Notices and Disclaimers
3 Additional Important Notices and Disclaimers
7 Chapter 1 Administration
1.1 Scope.
1.2 Purpose.
1.3 Application.
8 Chapter 2 Referenced Publications
2.1 General.
2.2 NFPA Publications. (Reserved)
2.3 Other Publications.
2.4 References for Extracts in Mandatory Sections.
Chapter 3 Definitions
3.1 General.
3.2 NFPA Official Definitions.
3.3 General Definitions.
Chapter 4 Test Equipment
4.1 Ignition Source.
9 4.2 Geometry and Construction of the Fire Test Room.
10 Chapter 5 Specimen Mounting
5.1 Specimen Mounting.
5.2 Materials Using Substrates.
11 5.3 Backing Materials.
5.4 Acoustical Materials and Other Board Materials.
12 5.5 Batt- or Blanket-Type Insulating and Other Flexible Materials.
5.6 Building Units.
5.7 Site-Fabricated Stretch Systems.
5.8 Wall or Ceiling Covering Materials.
13 5.9 Laminated Products with Wood Substrates.
5.10 Ceiling Lining Materials.
5.11 Reflective Insulation, Radiant Barrier, and Vinyl Stretch Ceiling Materials.
5.12 Specimen Installation.
5.13 Conditioning.
14 Chapter 6 Environmental Conditions
6.1 Fire Test Room Environment.
Chapter 7 Instrumentation
7.1 Fire Test Room Instrumentation.
15 7.2 Canopy Hood and Exhaust Duct.
7.3 Instrumentation in Exhaust Duct.
19 Chapter 8 Calibration
8.1 Calibration and Documentation of Ignition Source and Test Equipment.
8.2 Calibration Procedure.
20 8.3 Smoke Measurement Calibration.
8.4 Gas Analyzers Calibration.
Chapter 9 Test Procedure
9.1 Procedure.
Chapter 10 Calculation Methods
10.1 Mass Flow Rate.
10.2 Smoke Measurement Equations.
21 10.3 Release Rate of Combustion Gases.
10.4 Symbols.
22 Chapter 11 Report
11.1 Report.
11.2 Report of Significant Events.
11.3 Report of Single Point Key Properties.
11.4 Discussion of Performance.
23 Annex A Explanatory Material
25 Annex B Method of Determining Suitability of Oxygen Analyzers for Making Heat Release Measurements
Annex C Acceptance Criteria
26 Annex D Informational References

Related products

NFPA 286 2024
$80.71