NY StateMechanicalCode 2020 TEMP
$53.35
Mechanical Code of New York State
| Published By | Publication Date | Number of Pages |
| NY | 2020 | 170 |
This is a fully integrated custom code based on the 2018 International Mechanical Code.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | Cover |
| 2 | Copyright |
| 3 | ACKNOWLEDGEMENTS |
| 5 | PREFACE |
| 7 | EFFECTIVE USE |
| 11 | TABLE OF CONTENTS |
| 14 | 407 Ambulatory Care Facilities and Group |
| 15 | CHAPTER 1 SCOPE AND ADMINISTRATION Section 101 Title, Scope and Purpose 102 Applicability |
| 17 | 103 Administration and Enforcement |
| 18 | 104 Materials, Equipment and Methods of Construction 105 Building Permits, Construction Inspections, Stop Work Orders and Certificates of Occupancy |
| 20 | 106 Submittal Documents |
| 21 | 107 Service Utilities |
| 23 | CHAPTER 2 DEFINITIONS Section 201 General 202 General Definitions |
| 35 | CHAPTER 3 GENERAL REGULATIONS Section 301 General |
| 36 | 302 Protection of Structure |
| 37 | 303 Equipment and Appliance Location 304 Installation |
| 39 | 305 Piping Support 306 Access and Service Space |
| 41 | 307 Condensate Disposal |
| 42 | 308 Clearance Reduction 309 Temperature Control |
| 43 | 310 Explosion Control 311 Smoke and Heat Vents 312 Heating and Cooling Load Calculations |
| 45 | CHAPTER 4 VENTILATION Section 401 General 402 Natural Ventilation |
| 46 | 403 Mechanical Ventilation |
| 49 | 404 Enclosed Parking Garages 405 Systems Control 406 Ventilation of Uninhabited Spaces Occupancies |
| 55 | CHAPTER 5 EXHAUST SYSTEMS Section 501 General |
| 56 | 502 Required Systems |
| 63 | 503 Motors and Fans 504 Clothes Dryer Exhaust |
| 65 | 505 Domestic Cooking Exhaust Equipment 506 Commercial Kitchen Hood Ventilation System Ducts and Exhaust Equipment |
| 70 | 507 Commercial Kitchen Hoods |
| 73 | 508 Commercial Kitchen Makeup Air |
| 74 | 509 Fire Suppression Systems 510 Hazardous Exhaust Systems |
| 76 | 511 Dust, Stock and Refuse Conveying Systems |
| 77 | 512 Subslab Soil Exhaust Systems 513 Smoke Control Systems |
| 81 | 514 Energy Recovery Ventilation Systems |
| 83 | CHAPTER 6 DUCT SYSTEMS Section 601 General |
| 84 | 602 Plenums |
| 86 | 603 Duct Construction and Installation |
| 88 | 604 Insulation |
| 89 | 605 Air Filters 606 Smoke Detection Systems Control |
| 90 | 607 Duct and Transfer Openings |
| 95 | CHAPTER 7 COMBUSTION AIR Section 701 General |
| 97 | CHAPTER 8 CHIMNEYS AND VENTS Section 801 General |
| 98 | 802 Vents |
| 99 | 803 Connectors |
| 100 | 804 Direct-vent, Integral Vent and Mechanical Draft Systems |
| 101 | 805 Factory-built Chimneys |
| 102 | 806 Metal Chimneys |
| 103 | CHAPTER 9 SPECIFIC APPLIANCES, FIREPLACES AND SOLID FUEL-BURNING EQUIPMENT Section 901 General 902 Masonry Fireplaces 903 Factory-built Fireplaces 904 Pellet Fuel-burning Appliances 905 Fireplace Stoves and Room Heaters 906 Factory-built Barbecue Appliances 907 Incinerators and Crematories |
| 104 | 908 Cooling Towers, Evaporative Condensers and Fluid Coolers 909 Vented Wall Furnaces 910 Floor Furnaces |
| 105 | 911 Duct Furnaces 912 Infrared Radiant Heaters 913 Clothes Dryers 914 Sauna Heaters 915 Engine and Gas Turbine-powered Equipment and Appliances 916 Pool and Spa Heaters |
| 106 | 917 Cooking Appliances 918 Forced-air Warm-air Furnaces 919 Conversion Burners 920 Unit Heaters 921 Vented Room Heaters 922 Kerosene and Oil-fired Stoves and Heaters 923 Small Ceramic Kilns 924 Stationary Fuel Cell Power Systems |
| 107 | 925 Masonry Heaters 926 Gaseous Hydrogen Systems 927 Radiant Heating Systems 928 Evaporative Cooling Equipment 929 High-volume Large-diameter Fans |
| 109 | CHAPTER 10 BOILERS, WATER HEATERS AND PRESSURE VESSELS Section 1001 General 1002 Water Heaters 1003 Pressure Vessels 1004 Boilers |
| 110 | 1005 Boiler Connections 1006 Safety and Pressure Relief Valves and Controls |
| 111 | 1007 Boiler Low-water Cutoff 1008 Bottom Blowoff Valve 1009 Hot Water Boiler Expansion Tank |
| 112 | 1010 Gauges 1011 Tests |
| 113 | CHAPTER 11 REFRIGERATION Section 1101 General 1102 System Requirements |
| 114 | 1103 Refrigeration System Classification 1104 System Application Requirements |
| 121 | 1105 Machinery Room, General Requirements |
| 122 | 1106 Machinery Room, Special Requirements |
| 123 | 1107 Refrigerant Piping |
| 124 | 1108 Field Test |
| 125 | 1109 Periodic Testing |
| 127 | CHAPTER 12 HYDRONIC PIPING Section 1201 General 1202 Material |
| 128 | 1203 Joints and Connections |
| 129 | 1204 Pipe Insulation |
| 130 | 1205 Valves 1206 Piping Installation 1207 Transfer Fluid 1208 Tests |
| 131 | 1209 Embedded Piping 1210 Plastic Pipe Ground-source Heat Pump Loop Systems |
| 135 | CHAPTER 13 FUEL OIL PIPING AND STORAGE Section 1301 General 1302 Material 1303 Joints and Connections |
| 136 | 1304 Piping Support 1305 Fuel Oil System Installation 1306 Oil Gauging |
| 137 | 1307 Fuel Oil Valves 1308 Testing |
| 139 | CHAPTER 14 SOLAR THERMAL SYSTEMS Section 1401 General 1402 Design and Installation |
| 141 | 1403 Heat Transfer Fluids 1404 Labeling |
| 143 | CHAPTER 15 REFERENCED STANDARDS |
| 157 | APPENDIX A CHIMNEY CONNECTOR PASS-THROUGHS |
| 159 | APPENDIX B RESERVED |
| 161 | INDEX |
Related products
-
NY StateMechanicalCode 2020
Mechanical Code of New York State Published By Publication Date Number of Pages NY 2020…
