29.080.20 – Bushings – PDF Standards Store

JIS C 3824:1981

Wed, 06 Nov 2024 02:00:48 +0000

High-Voltage Porcelain Tubes

Published By	Publication Date	Number of Pages
JIS	1981-03-01	9

IEC/IEEE 65700-19-03:2014

Tue, 05 Nov 2024 20:15:00 +0000

IEC/IEEE 65700-19-03:2014 applies to outdoor and indoor bushings of any voltage used on DC systems, of capacitance graded or gas insulated types for use as components of oil-filled converter transformers and smoothing reactors, as well as air-to-air DC bushings. This standard makes reference to IEC 60137 for general terms and conditions and defines the special terms used, operating conditions, ratings, test procedures as well as general mechanical and electrical requirements for bushings for DC application. This standard replaces IEC 62199:2004, Bushings for DC application.

IEC TS 61464:1998

Tue, 05 Nov 2024 20:10:11 +0000

Traversées isolées. Guide d'interprétation de l'analyse des gaz dissous (AGD) dans les traversées ou l'huile est l'imprégnant de l'isolation principale (papier généralement)

Published By	Publication Date	Number of Pages
IEC	1998-08-25	40

IEC TS 61463:2016

Tue, 05 Nov 2024 20:10:10 +0000

IEC TS 61463:2016(E), which is a Technical Specification, is applicable to alternating current and direct current bushings for highest voltages above 52 kV (or with resonance frequencies placed inside the seismic response spectrum), mounted on transformers, other apparatus or buildings. For bushings with highest voltages less than or equal to 52 kV (or with resonance frequencies placed outside from the seismic response spectrum), due to their characteristics, seismic qualification is not used as far as construction practice and seismic construction practice comply with the state of the art. This document presents acceptable seismic qualification methods and requirements to demonstrate that a bushing can maintain its mechanical properties, insulate and carry current during and after an earthquake. The seismic qualification of a bushing is only performed upon request.

IEC 62199:2004

Tue, 05 Nov 2024 19:41:19 +0000

Bushings for d.c. application

Published By	Publication Date	Number of Pages
IEC	2004-05-14	58

IEC 60137:2017

Tue, 05 Nov 2024 18:40:38 +0000

Traversées isolées pour tensions alternatives supérieures à 1000 V

Published By	Publication Date	Number of Pages
IEC	2017-06-22	128

IEC 60137:2008

Tue, 05 Nov 2024 18:40:37 +0000

IEC 60137:2008 gives the characteristics and tests for insulated bushings intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1 000 V and power frequencies of 15 Hz up to and including 60 Hz. Special requirements and tests for transformer bushings in this standard apply also to reactor bushings. This edition includes the following significant technical changes with respect to the previous edition:
– Long duration power-frequency for transformer bushings;
– Special requirements for type and acceptance tests applicable to transformer and GIS bushings;
– Specific insulation levels for bushings fitted to transformers and GIS;
– According to IEC Guide 111, clauses relating to safety and the environment have been added; and
– The altitude correctino procedure has been revised (> 1 000 m).

DIN 89349:2008 Edition

Tue, 05 Nov 2024 15:19:00 +0000

Dichtringe für Einführungen für elektrische Kabel und Leitungen

Published By	Publication Date	Number of Pages
DIN	2008-02	5

DIN 89345:2006 Edition

Tue, 05 Nov 2024 15:18:59 +0000

Erdungseinsätze für Einführungen für elektrische Kabel und Leitungen

Published By	Publication Date	Number of Pages
DIN	2006-01	10

DIN 89285:2015 Edition

Tue, 05 Nov 2024 15:18:59 +0000

Einführungen für elektrische Kabel und Leitungen - Kabelverschraubung mit Schutzgrad IP66 und IP68 zur Anwendung auf Wasserfahrzeugen

Published By	Publication Date	Number of Pages
DIN	2015-09	15