29.100.99 – Other components for electrical equipment – PDF Standards Store

BS EN IEC 61969-1:2023

Sun, 20 Oct 2024 07:26:00 +0000

This part of IEC 61969 contains design guidelines for outdoor enclosures for electrical and electronic equipment and is applicable over a wide field of mechanical, electromechanical and electronic equipment and its installation where a modular design is used. The objectives of this document are: – to provide an overview of specifications for enclosures focused on requirements for outdoor applications for stationary use at non-weather protected locations, and – to achieve product integrity under outdoor conditions and to ease product selection for the sourcing of outdoor enclosures from different vendors. These enclosures are considered to contain any equipment and provide protection for the outdoor installed facilities against unwanted environmental impacts. The installed equipment can be, but is not limited to, subracks or chassis according to IEC 60917 (all parts) or IEC 60297 (all parts). A typical outdoor enclosure is shown in Figure 1. [Figure 1]

PDF Catalog

PDF Pages	PDF Title
2	undefined
5	Annex ZA (normative)Normative references to international publicationswith their corresponding European publications
8	Blank Page
9	English CONTENTS
10	FOREWORD
12	INTRODUCTION
13	1 Scope Figure 1 – Typical outdoor enclosure
14	2 Normative references
15	3 Terms and definitions
16	4 Coordination dimensions 5 Environmental requirements, tests and safety aspects 5.1 Classification of environmental conditions Figure 2 – Locations of outdoor enclosures
17	Table 1 – Operating and transportation conditions
18	5.2 Transportation and installation related mechanical loads 5.3 Operational related mechanical loads 5.4 Static load capacity Table 2 – Safety aspects
19	5.5 Seismic performance 6 Electromagnetic shielding 7 Thermal management and acoustic noise emission
20	Bibliography

BSI 21/30447583 DC:2021 Edition

Sun, 20 Oct 2024 03:37:45 +0000

BS EN 61969-1. Mechanical structures for electrical and electronic equipment. Outdoor enclosures - Part 1. Design guidelines

Published By	Publication Date	Number of Pages
BSI	2021	16

BS EN 62262:2002+A1:2021

Sun, 20 Oct 2024 03:30:25 +0000

Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)

Published By	Publication Date	Number of Pages
BSI	2021	16

BSI 19/30406422 DC:2019 Edition

Sat, 19 Oct 2024 16:44:04 +0000

BS EN 63044-5-2 AMD1. Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) - Part 5-2. EMC requirements for HBES/BACS used in residential, commercial and light-industrial environments

Published By	Publication Date	Number of Pages
BSI	2019	4

BSI 19/30403602 DC:2019 Edition

Sat, 19 Oct 2024 16:43:59 +0000

Published By	Publication Date	Number of Pages
BSI	2019	15

BSI 20/30411150 DC:2020 Edition

Sat, 19 Oct 2024 16:09:10 +0000

PDF Catalog

PDF Pages	PDF Title
1	30411150-NC
3	70_146e_CD
5	FOREWORD
6	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES 1 Scope 2 Normative references 2 Definitions
7	4 Designations 4.1 Arrangement of the IK code 4.2 Characteristic group numerals of the IK code and their meanings

BSI 19/30390169 DC:2019 Edition

Sat, 19 Oct 2024 16:08:15 +0000

BS EN 62262 AMD1. Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)

Published By	Publication Date	Number of Pages
BSI	2019	4

BS EN 62262:2002

Sat, 19 Oct 2024 15:58:01 +0000

A classification system to promote a uniform method for determining the various degrees of protection and describes the tests to prove the various degrees of protection.

PDF Catalog

PDF Pages	PDF Title
1	BRITISH STANDARD
2	Committees responsible for this British Standard
3	Short contents
6	Foreword Contents
7	Introduction 1 Scope 2 Normative references
8	3 Definitions 3.1 enclosure 3.2 degree of protection against mechanical impacts 3.3 IK code 4 Designations 4.1 Arrangement of the IK code 4.2 Characteristic group numerals of the IK code and their meanings 4.3 Application of the IK code
9	4.4 Marking 5 General requirements for tests 5.1 Atmospheric conditions for tests 5.2 Enclosures under test 5.3 Specifications to be given in the relevant product standard 6 Test to verify the protection against mechanical impacts 6.1 The tests specified in this standard are type tests. 6.2 In order to verify the protection against mechanical impacts blows shall be applied to the en… 6.3 During the test the enclosure shall be mounted, according to the manufacturer instructions fo… 6.4 The number of impacts shall be five on each exposed face unless otherwise specified in the re…
10	6.5 Test evaluation 7 Test apparatus

BS 5490:1977:1986 Edition

Sat, 19 Oct 2024 15:56:56 +0000

This standard provides a system for specifying the enclosures of electrical equipment on the basis of the degree of protection provided by the enclosure. It is applicable to enclosures where the rated voltage of the equipment inside the enclosure does not exceed 72.5 kV.

It also specifies type tests to check the performance of the various classes of enclosure.

The type of protection covered by this system of classification is as follows:

Protection of persons against contact with or approach to live parts and against contact with moving parts (other than smooth rotating shafts and the like) inside the enclosure and protection of the equipment against ingress of solid foreign bodies.
Protection of the equipment inside the enclosure against harmful ingress of water.

Notes 1. — The protection of moving parts external to the enclosure, such as fans, is a matter for the relevant Technical Committee.

2. — In this standard, the tests are conducted with fresh water.

This standard deals only with enclosures that are in all other respects suitable for their intended use and which, from the point of view of materials and workmanship, ensure that the properties dealt with in this standard are maintained under the normal conditions of use.

The standard does not specify degrees of protection against mechanical damage of the equipment, risk of explosions, or conditions such as moisture (produced for example by condensation), corrosive vapours, fungus or vermin.

Fences or guards external to the enclosure which have to be provided solely for the safety of personnel are not considered part of the enclosure and are not dealt with.

Classifies degrees of protection provided by enclosures on all types of electrical equipment where the rated voltage does not exceed 72.5 kV. The IP system employed indicates by means of a two numeral code the protection afforded against contact with live and moving parts, also against ingress of solid objects and moisture. Tests to verify degree of protection.

BSI 19/30392188 DC:2019 Edition

Sat, 19 Oct 2024 15:41:32 +0000

BS EN 62975. Natural esters. Guidelines for maintenance and use in electrical equipment

Published By	Publication Date	Number of Pages
BSI	2019	33