31.220.01 – Electromechanical components in general – PDF Standards Store

JIS C 5402-23-3:2005

Wed, 06 Nov 2024 02:02:19 +0000

Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 23-3: Test 23c: Shielding effectiveness of connectors and accessories

Published By	Publication Date	Number of Pages
JIS	2005-03-20	12

JIS C 5402-20-2:2005

Wed, 06 Nov 2024 02:02:18 +0000

Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 20-2: Test 20b - Flammability tests – Fire-proofness

Published By	Publication Date	Number of Pages
JIS	2005-03-20	12

IEC TR 62225:2001

Tue, 05 Nov 2024 20:04:36 +0000

Guidance on terms for connectors and mechanical structures in electronic equipment

Published By	Publication Date	Number of Pages
IEC	2001-11-27	54

IEC 60603-7:2020

Tue, 05 Nov 2024 18:57:37 +0000

IEC 60603-7:2020 covers 8-way, unshielded, free and fixed connectors and is intended to specify the common dimensions (interface dimensions), mechanical, electrical and environmental characteristics and tests for the family of IEC 60603-7-x connectors. These connectors are intermateable (according to IEC 61076-1 level 2) and interoperable with other IEC 60603-7 series connectors. This fourth edition cancels and replaces the third edition, published in 2008, its Amendment 1:2011 and its Amendment 2:2019. It constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition:
– Revised the definitions for intermateability and interoperability; added new definitions.
– Corrected dimension line for dimension AZ2 in Figure 5.
– Corrected dimension line for dimension F1 in Figure A.1.
– Revised the reference to ISO/IEC 11801 to ISO/IEC 11801-1.
– Added lower limiting temperature and upper limiting temperature definitions.
– Revised Table 1 to Table 8 so the column order is Minimum-Nominal-Maximum dimensions (ascending order).
– Corrected Table 7: Climatic category and Upper temperature values to 90 °C (to be consistent with the graph in Figure 10 and Note 1 in Figure 10).
– Revised the wording in 8.2, contact resistance, for clarification.
– Revised Figure 11 and Figure 12 and the wording in the Key below for clarification.
– Removed the sentences under the figure in the Introduction.
– Added Annex E.

IEC 60512-9-5:2010

Tue, 05 Nov 2024 18:54:29 +0000

Connectors for electronic equipment - Tests and measurements - Part 9-5: Endurance tests - Test 9e: Current loading, cyclic

Published By	Publication Date	Number of Pages
IEC	2010-03-17	14

IEC 60512-9-5:2020

Tue, 05 Nov 2024 18:54:29 +0000

Connecteurs pour équipements électriques et électroniques - Essais et mesures - Partie 9-5: Essais d'endurance - Essai 9e: Charge en courant, essai cyclique IEC

Published By	Publication Date	Number of Pages
IEC	2020-06-09	26

IEC 60512-9-3:2011

Tue, 05 Nov 2024 18:54:28 +0000

Connecteurs pour équipements électroniques - Essais et mesures - Partie 9-3 : essais d'endurance - Essai 9c : fonctionnement mécanique (d'accouplement et de désaccouplement) avec charge électrique

Published By	Publication Date	Number of Pages
IEC	2011-06-22	22

IEC 60512-9-4:2011

Tue, 05 Nov 2024 18:54:28 +0000

Connecteurs pour équipements électroniques - Essais et mesures - Partie 9-4 : essais d'endurance - Essai 9d : durabilité du système de rétention des contacts et des joints d'étanchéité (entretien, vieillissement)

Published By	Publication Date	Number of Pages
IEC	2011-04-07	16

IEC 60512-9-2:2011

Tue, 05 Nov 2024 18:54:27 +0000

Connecteurs pour équipements électroniques - Essais et mesures - Partie 9-2 : essais d'endurance - Essai 9b : charge électrique et température

Published By	Publication Date	Number of Pages
IEC	2011-11-28	18

IEC 60512-9-1:2010

Tue, 05 Nov 2024 18:54:26 +0000

Connecteurs pour équipements électroniques - Essais et mesures - Partie 9-1 : essais d'endurance - Essai 9a : fonctionnement mécanique

Published By	Publication Date	Number of Pages
IEC	2010-03-17	14