33.060.40 – Cabled distribution systems – PDF Standards Store

NZS 6603:1984

Wed, 06 Nov 2024 05:13:14 +0000

Sets out recommendations for good reception and reticulation of sound and television signals in buildings on a single site. Intended for the guidance of architects, contractors and building owners who are involved with the planning, installation and maintenance of MATV systems. Does not provide the detailed information required by the systems engineer to design a complete system, as such information is available in handbooks published by manufacturers. Includes recommendations regarding the provision of antenna systems and coaxial cable distribution systems, the necessary structural accommodation for equipment and wiring, and protective measures against danger from electric shock, fire and other hazards.

IEC TR 60728-3-2:2016

Tue, 05 Nov 2024 20:00:47 +0000

Cable networks for television signals, sound signals and interactive services - Part 3-2: Method of measurement of 5th order non-linearity for active electronic equipment using five carriers

Published By	Publication Date	Number of Pages
IEC	2016-10-05	28

IEC 60728-9:2000/AMD1:2005

Tue, 05 Nov 2024 19:01:23 +0000

Amendment 1 - Cabled distribution systems for television and sound signals - Part 9: Interfaces of cables distribution systems for digitally modulated signals

Published By	Publication Date	Number of Pages
IEC	2005-06-27	66

IEC 60728-9:2000

Tue, 05 Nov 2024 19:01:22 +0000

Cabled distribution systems for television and sound signals - Part 9: Interfaces of cabled distribution systems for digitally modulated signals

Published By	Publication Date	Number of Pages
IEC	2000-11-15	56

IEC 60728-6:2011

Tue, 05 Nov 2024 19:01:19 +0000

IEC 60728-6:2011(E) lays down the measuring methods, performance requirements and data publication requirements of optical equipment of cable networks for television signals, sound signals and interactive services. This third edition cancels and replaces the second edition published in 2003 of which it constitutes a technical revision. It includes the following significant technical changes with respect to the previous edition:
– The normative references were updated.
– The methods of measurement for optical power and return loss were substituted by references to other standards.
– The method of measurement for polarization dependent loss was deleted.
– A method of measurement for carrier-to-crosstalk ratio (CCR) was added.
– The methods of measurement for CSO and CTB of optical amplifiers were substituted by a method of measurement for microscopic gain tilt of optical amplifiers.
This parameter can be used for calculating the second order distortion of optical amplifiers according to the method described in the new Annex B. New classes for optical transmitters and receivers have been defined.

IEC 60728-4:2007

Tue, 05 Nov 2024 19:01:18 +0000

IEC 60728-4:2007 applies to system outlets, splitters and taps, passive single or multiple port equipment comprising filters, attenuators, equalizers, galvanic isolators, power injectors, cable splices, terminating resistors and transfer points, but excluding coaxial cables and receiver leads. This standard:
– covers the frequency range 5 MHz to 3 000 MHz;
– identifies performance requirements for certain parameters;
– lays down data publication requirements for certain parameters;
– stipulates methods of measurements;
– introduces minimum requirements defining quality grades. This third edition cancels and replaces the second edition published in 2000, of which it constitutes a technical revision. It includes the following significant technical changes: Subclause 3.1 includes several new or modified definitions. Clause 4 includes added test methods for attenuation, isolation, through-loss, group delay variation, amplitude frequency response and two carrier intermodulation measurements for second- and third-order products. Clause 5 includes updated and new performance requirements.

IEC 60728-5:2015

Tue, 05 Nov 2024 19:01:18 +0000

Réseaux de distribution par câbles pour signaux de télévision, signaux de radiodiffusion sonore et services interactifs - Partie 5: Équipements de tête de réseau

Published By	Publication Date	Number of Pages
IEC	2015-12-09	192

IEC 60728-5:2007

Tue, 05 Nov 2024 19:01:18 +0000

It defines the characteristics of equipment used in the headends of terrestrial broadcast and satellite receiving systems (without satellite outdoor units and without those broadband amplifiers in the headend as described in IEC 60728-3). The satellite outdoor units for FSS are described in ETSI ETS 300 158, for BSS in ETSI ETS 300 249. Test methods for both types (FSS and BSS) of satellite outdoor units are laid down in ETSI ETS 300 457. This edition includes the following significant technical changes with respect to the previous edition: Revised title and scope Clause 3, several new terms and definitions Subclause 4.1, Methods of measurement for digitally modulated signals Subclause 4.6.2, RF signal-to-noise ratio (SD,RF/N) for digitally modulated signals Subclause 4.8.2, Procedure for the measurement of group delay variation on DVB channel converters Subclause 4.9, Phase noise of an RF carrier Subclause 4.15, Decoding margin (Teletext). Annex D, Special national conditions. Annex E, Correction factors for noise. Annex F, Digital signal level and bandwidth. Annex G, Minimum frequency distance of converted satellite signals in the IF range. Annex H, Measurement errors which occur due to mismatched equipment. .Annex I, Correction factor for spectrum analyser

IEC 60728-3:2017

Tue, 05 Nov 2024 19:01:17 +0000

IEC 60728-3:2017 is also available as IEC 60728-3:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60728-3:2017 specifies the measuring methods, performance requirements and data publication requirements for active wideband equipment of cable networks for television signals, sound signals and interactive services. This fifth edition cancels and replaces the fourth edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) extension of upper frequency range limit for cable network equipment in the forward path from 1000 MHz to 1218 MHz (optional up to 1794 MHz);
b) extension of upper frequency range limit for cable network equipment in the return path from 85 MHz to 204 MHz;
c) integration and update of IEC 60728-3-1 content;
d) integration and update of the Technical Specification CLC/TS 50083-3-3 content;
e) deletion of specifications and test methods for obsolete analogue parameters;
f) additional normative references;
g) additional terms and definitions and abbreviations.

IEC 60728-3:2010

Tue, 05 Nov 2024 19:01:17 +0000

IEC 60728-3:2010 lays down the measuring methods, performance requirements and data publication requirements for active wideband equipment of cable networks for television signals, sound signals and interactive services. This fourth edition cancels and replaces the third edition published in 2005 of which it constitutes a technical revision. It includes the following significant technical changes with respect to the previous edition:
– extension of upper frequency range limit for cable network equipment from 862 MHz to 1 000 MHz;
– method of measurement and requirements for immunity to surge voltages;
– extension of scope to equipment using symmetrical ports;
– additional normative references;
– additional terms and definitions and abbreviations. The French version of this standard has not been voted upon.