43.040.01 – Road vehicle systems in general – PDF Standards Store

JIS D 4607:1977

Wed, 06 Nov 2024 02:09:52 +0000

Three Dimensional Manikins for Use in Defining Automobile Seating Accommodations

Published By	Publication Date	Number of Pages
JIS	1977-11-01	16

JIS D 0050:1983

Wed, 06 Nov 2024 02:08:12 +0000

Load Distribution for Passenger Cars

Published By	Publication Date	Number of Pages
JIS	1983-02-01	6

JIS D 0030:1982

Wed, 06 Nov 2024 02:08:10 +0000

Three-Dimensional Reference System for Automobiles

Published By	Publication Date	Number of Pages
JIS	1982-03-01	5

JIS D 0024:1985

Wed, 06 Nov 2024 02:08:10 +0000

Road Vehicles - Procedure for H-point Determination

Published By	Publication Date	Number of Pages
JIS	1985-03-01	10

JIS D 0023:1984

Wed, 06 Nov 2024 02:08:10 +0000

Driver Hand Control Reach for Passenger Cars

Published By	Publication Date	Number of Pages
JIS	1984-04-01	29

JIS C 4607:1991

Wed, 06 Nov 2024 02:01:14 +0000

AC load break switches with tripping device for 3.3 kV or 6.6 kV

Published By	Publication Date	Number of Pages
JIS	1991-10-01	32

ISO/TS 18571:2014

Wed, 06 Nov 2024 01:29:47 +0000

ISO/TS 18571:2014 provides validation metrics and rating procedures to be used to calculate the level of correlation between two non-ambiguous signals obtained from a physical test and a computational model, and is aimed at vehicle safety applications. The objective comparison of time-history signals of model and test is validated against various loading cases under different types of physical loads such as forces, moments, and accelerations. However, other applications might be possible too, but are not within the scope of ISO/TS 18571:2014.

ISO 4081:2016

Tue, 05 Nov 2024 23:15:04 +0000

ISO 4081:2016 specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in internal-combustion engines for vehicles with an unladen mass (as defined in ISO 1176) of 3,5 t or less. In addition, this specification may also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a "line call-out" of tests for specific applications where these are not covered by the main types specified (see example in Annex D). In this case, the hose or tubing would not carry any marking showing this ISO specification number but may detail the OEM's own identification markings as shown on their part drawings.

ISO 4081:2010

Tue, 05 Nov 2024 23:15:01 +0000

ISO 4081:2010 specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in internal-combustion engines for vehicles with an unladen mass (as defined in ISO 1176) of 3,5 t or less. In addition, this specification may also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a “line call-out” of tests for specific applications where these are not covered by the main types specified. In this case, the hose or tubing would not carry any marking showing this ISO specification number but may detail the OEM's own identification markings as shown on their part drawings.

ISO 17324:2014

Tue, 05 Nov 2024 21:59:03 +0000

Rubber hoses for automotive turbochargers — Specification

Published By	Publication Date	Number of Pages
ISO	2014-09	20