53.060 – Industrial trucks – PDF Standards Store ?u= Wed, 06 Nov 2024 04:57:54 +0000 en-US hourly 1 https://wordpress.org/?v=6.7.1 ?u=/wp-content/uploads/2024/11/cropped-icon-150x150.png 53.060 – Industrial trucks – PDF Standards Store ?u= 32 32 SAE J 992:1998 ?u=/product/publishers/sae/sae-j-9921998/ Wed, 06 Nov 2024 04:57:54 +0000 Brake System Performance Requirements--Truck, Bus, and Combination of Vehicles
Published By Publication Date Number of Pages
SAE 1998-12-23 5
]]> This SAE Recommended Practice presents performance requirements for the brake systems of motor vehicles intended for roadway use and falling into the following classifications: Light trucks and buses: 6001-10 000 lb (2700-4500 kg) gvw; Truck and bus: Over 10 000 lb (4500 kg) gvw; combination of vehicles towing vehicles over 10 000 lb (4500 kg) gvw. Acceptable performance requirements are based on data obtained from applicable sections of SAE J786a (March, 1978). The purpose of this recommended practice is to establish the minimum brake system performance requirements with regard to: 3.1 Stopping ability–of cold brakes, as affected by vehicle speed. 3.2 Stopping ability–of hot brakes, as affected by vehicle speed and duty cycle. 3.3 Pedal force (air pressure) requirements–maximum allowable. 3.4 Brake stability. 3.5 stopping ability and recovery of wet brakes. 3.6 Stopping ability of emergency brake system. 3.7 Brake effectiveness distribution for vehicles in combination.

]]> SAE J 875:2011 ?u=/product/publishers/sae/sae-j-8752011/ Wed, 06 Nov 2024 04:57:05 +0000 Trailer Axle Alignment
Published By Publication Date Number of Pages
SAE 2011-06-13 5
]]>
The scope of this SAE Recommended Practice, trailer axle alignment, is to identify the dimensional limits of, and a method to, establish a perpendicular relationship between the king pin centerline and the axle centerline at its midpoint. Various types of equipment are commercially available which can be used for this measurement which provides varying degrees of accuracy, but none can be endorsed by SAE.
The most fundamental methods of measurement will be described here, but other equipment is available if a greater degree of accuracy is desired.
]]> SAE J 849:2013 ?u=/product/publishers/sae/sae-j-8492013/ Wed, 06 Nov 2024 04:56:54 +0000 Connection and Accessory Locations for Towing Multiple Trailers - Truck and Bus
Published By Publication Date Number of Pages
SAE 2013-01-04 5
]]>
This SAE Recommended Practice establishes the recommended locations for the air brake and electrical connections for towing multiple trailers. It applies to all commercial trailers except drop frame and car haul types.
]]> SAE J 847:2011 ?u=/product/publishers/sae/sae-j-8472011/ Wed, 06 Nov 2024 04:56:53 +0000 Trailer Tow Bar Eye and Pintle Hook/Coupler Performance
Published By Publication Date Number of Pages
SAE 2011-07-13 6
]]>
This SAE Recommended Practice applies to highway trailer tow bar eye-type applications, including multiple trailers.
]]> SAE J 786A:1998 ?u=/product/publishers/sae/sae-j-786a1998/ Wed, 06 Nov 2024 04:56:32 +0000 Brake System Road Test Code - Truck, Bus, and Combination of Vehicles
Published By Publication Date Number of Pages
SAE 1998-12-01 24
]]> This SAE Recommended Practice establishes a uniform procedure for the level road test of the brake systems of new trucks, buses, and combination of vehicles designed for roadway use and falling in the following classifications:

Light trucks and buses: 6001–10,000 lb (2700–4500 kg) gvw

Truck and bus: Over 10,000 lb (4500 kg) gvw

Combination of vehicles (towing vehicle over 10,000 lb (4500 kg) gvw)

]]> SAE J 704:2017 ?u=/product/publishers/sae/sae-j-7042017/ Wed, 06 Nov 2024 04:56:03 +0000 Openings for Six- and Eight-Bolt Truck Transmission Mounted Power Take-Offs
Published By Publication Date Number of Pages
SAE 2017-11-03 4
]]>
The accompanying mounting and gear locations are applicable for all general installations of power take-off on the transmission gear box of motor trucks and tractors where the size of the transmission permits.
The heavy-duty type opening can be adapted to the regular-duty type by the use of an adapter with 6.35 mm (0.25 in) flange thickness with appropriate bolt pattern and thread engagement. (See Figures 1 and 2.)
]]> SAE J 701:2017 ?u=/product/publishers/sae/sae-j-7012017/ Wed, 06 Nov 2024 04:56:01 +0000 Truck Tractor Semitrailer Interchange Coupling Dimensions
Published By Publication Date Number of Pages
SAE 2017-08-09 6
]]>
The information in this SAE Information Report is the result of studies by the Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimensional limitations for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject.
Some cases will require more care in application allowing splash shield clearance at trailer support interference points and positioning fifth wheel to allow trailer swing clearance on an 11% grade. All dimensions are given in inches.
Table 1 and Figures 1 and 2 show basic requirements for interchangeability of truck tractor and semitrailer equipment. Figure 3 shows the interchangeability of the doubles converter dolly.
The formulas for determining LWC, OAL and CFW are:
where:

FW

= fifth wheel advance

R

= Rear axle tire radius

LWC

= 90 in
= 64 in (short trailers specifically intended for use with two axle tractors)

W

= 96 in
= 102 in

C

= Clearance, 4 in
where:

H

= Distance from intersection at back of cab and trailer swing radius to top of fifth wheel with zero trailer clearance to first obstruction

FWP

= Top face of fifth wheel to centerline of pivot, 3.50 in

SR

= Swing radius of trailer corner
]]> SAE J 699:2011 ?u=/product/publishers/sae/sae-j-6992011/ Wed, 06 Nov 2024 04:55:59 +0000 Average Vehicle Dimensions for Use in Designing Docking Facilities for Motor Vehicles
Published By Publication Date Number of Pages
SAE 2011-06-13 3
]]>
This SAE Recommended Practice establishes limits for empty vehicle floor heights and provides limits of vehicle dimensions for use in designing docking facilities for motor vehicles.
]]> SAE J 697:2011 ?u=/product/publishers/sae/sae-j-6972011/ Wed, 06 Nov 2024 04:55:58 +0000 Safety Chain of Full Trailers or Converter Dollies
Published By Publication Date Number of Pages
SAE 2011-07-13 4
]]>
This SAE Recommended Practice covers the number, location, and method of attachment of safety chains for full trailers and/or converter dollies.
]]> SAE J 691:2011 ?u=/product/publishers/sae/sae-j-6912011/ Wed, 06 Nov 2024 04:55:56 +0000 Motor Truck Ca Dimensions
Published By Publication Date Number of Pages
SAE 2011-06-13 3
]]>
This SAE Recommended Practice sets forth recommended back of cab to rear axle (CA) dimensional data. It applies to 4- and 6-wheel motor trucks but not necessarily to truck-tractors.
]]>