77.040.10 – Mechanical testing of metals – PDF Standards Store

JIS Z 3197:2012

Wed, 06 Nov 2024 03:00:50 +0000

This Standard specifies the test methods for soldering fluxes (hereafter referred to as "fluxes") mainly intended for connection of wiring and parts in electric and electronic apparatuses and communication devices.

NOTE: The International Standards corresponding to this Standard and the symbol of degree of correspondence are as follows.

ISO 9454-1: 1990 Soft soldering fluxes-Classification and requirementsPart 1: Classification, labelling and packaging

ISO 9455-1: 1990 Soft soldering fluxes-Test methods-Part 1: Determination of non-volatile matter, gravimetric method

ISO 9455-3: 1992 Soft soldering fluxes-Test methods-Part 3: Determination of acid value, potentiometric and visual titration methods

ISO 9455-5: 1992 Soft soldering fluxes-Test methods-Part 5: Copper mirror test

ISO 9455-6: 1995 Soft soldering fluxes-Test methods-Part 6: Determination and detection of halide (excluding fluoride) content

ISO 9455-10: 1998 Soft soldering fluxes-Test methods-Part 10: Flux efficacy tests, solder spread method

ISO 9455-13: 1996 Soft soldering fluxes-Test methods-Part 13: Determination of flux spattering

ISO 9455-14: 1991 Soft soldering fluxes-Test methods-Part 14: Assessment of tackiness of flux residues

ISO 9455-15: 1996 Soft soldering fluxes-Test methods-Part 15: Copper corrosion test

ISO 9455-16: 1998 Soft soldering fluxes-Test methods-Part 16: Flux efficacy tests, wetting balance method

ISO 9455-17: 2002 Soft soldering fluxes-Test methods-Part 17: Surface insulation resistance comb test and electrochemical migration test of flux residues

ISO 12224-2: 1997 Flux cored solder wire-Specification and test methods- Part 2: Determination of flux content

IEC 61189-5: 2006 Test methods for electrical materials, interconnection structures and assemblies-Part 5: Test methods for printed board assemblies

IEC 61189-6: 2006 Test methods for electrical materials, interconnection structures and assemblies-Part 6: Test methods for materials used in manufacturing electronic assemblies

IEC 61190-1-1: 2002 Attachment materials for electronic assemblyPart 1-1: Requirements for soldering fluxes for high-quality interconnections in electronics assembly (Overall evaluation: MOD)

The symbols which denote the degree of correspondence in the contents between the relevant International Standards and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISOI/IEC Guide 21-1.

WARNING Persons carrying out tests based on this Standard should be familiar with normal laboratory practice.

This Standard does not purport to address all of the safety problems, if any, associated with its use.

It is the responsibility of the user of this Standard to establish appropriate safety and health practices.

JIS Z 3139:2009

Wed, 06 Nov 2024 03:00:37 +0000

Methods of macro testing and Vickers hardness testing for section of resistance spot, projection and seam welds

Published By	Publication Date	Number of Pages
JIS	2009-10-20	15

JIS Z 2512:2012

Wed, 06 Nov 2024 02:59:43 +0000

This Standard specifies the determination method for the tap density (the density of powder when tapped into a container under specified conditions).

NOTE: The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows.

ISO 3953:2011 Metajjicpowders-Determination of tap density (MOD)

In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/lEe Guide 21-1.

JIS Z 2511:2006

Wed, 06 Nov 2024 02:59:42 +0000

Metallic powders - Determination of green strength by transverse rupture of rectangular compacts

Published By	Publication Date	Number of Pages
JIS	2006-07-20	17

JIS Z 2507:2000

Wed, 06 Nov 2024 02:59:39 +0000

Sintered Metal Bearing - Determination of Radial Crushing Strength

Published By	Publication Date	Number of Pages
JIS	2000-03-20	7

JIS Z 2288:2003

Wed, 06 Nov 2024 02:58:55 +0000

Methods of Tensile Shear Test and Bend Test for Thin Clad Steel Sheets

Published By	Publication Date	Number of Pages
JIS	2003-03-20	8

JIS Z 2277:2000

Wed, 06 Nov 2024 02:58:50 +0000

Method of Tensile Testing for Metallic Materials in Liquid Helium

Published By	Publication Date	Number of Pages
JIS	2000-03-20	15

JIS Z 2276:2012

Wed, 06 Nov 2024 02:58:49 +0000

This Standard specifies the method of tensile stress relaxation test in which the relaxation [the change of test force (stress) over time] of tensile test force (stress) for metallic materials is measured under the condition of a constant tensile total strain and of a constant temperature.

NOTE: The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows.

ISO 15630-3 : 2010 Steel for the reinforcement and prestressing of concrete – Test methods – Part 3 : Prestressing steel (MOD)

Warning Persons carrying out tests based on this Standard should be familiar with normal laboratory practice.

This Standard does not purport to address all of the safety problems, if any, associated with its use.

It is the responsibility of the user of this Standard to establish appropriate safety and health practices.

JIS Z 2275:1978

Wed, 06 Nov 2024 02:58:47 +0000

This Japanese Industrial Standard specifies the method of plane bending fatigue testing of metal plates by the use of standard test pieces to be carried out in the atmospheric air at room temperature, covering fatigue life at the number of stress cycles not less than 104 times.

The plane bending herein signifies a loading method in such a manner that the repeated bending moment is applied to a plate-shaped test piece in the plane intersecting the plate surface perpendicularly and including the axis of the test piece.

JIS Z 2274:1978

Wed, 06 Nov 2024 02:58:46 +0000

Method of Rotating Bending Fatigue Testing of Metals

Published By	Publication Date	Number of Pages
JIS	1978-07-01	12