77.120.20 – Magnesium and magnesium alloys – PDF Standards Store ?u= Wed, 06 Nov 2024 05:02:47 +0000 en-US hourly 1 https://wordpress.org/?v=6.7.1 ?u=/wp-content/uploads/2024/11/cropped-icon-150x150.png 77.120.20 – Magnesium and magnesium alloys – PDF Standards Store ?u= 32 32 SAE USCAR 35-1:2020 ?u=/product/publishers/sae/sae-uscar-35-12020/ Wed, 06 Nov 2024 05:02:47 +0000 Test Procedures for Evaluating Bolt-Load Retention of Magnesium Alloys
Published By Publication Date Number of Pages
SAE 2020-11-19 14
]]>
A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications.
]]> SAE MAP 1670A:2015 ?u=/product/publishers/sae/sae-map-1670a2015/ Wed, 06 Nov 2024 05:02:10 +0000 Studs, Installation Practice for Interference Fit - Metric
Published By Publication Date Number of Pages
SAE 2015-08-14 6
]]>
This document provides a recommended practice for installation of interference fit studs into threaded holes in non-ferrous alloys such as aluminum or magnesium.
]]> SAE MAM 4427A:2003 ?u=/product/publishers/sae/sae-mam-4427a2003/ Wed, 06 Nov 2024 05:02:01 +0000 Magnesium Alloy Sand Castings 4.0Y 2.3Nd 0.7Zr Solution and Precipitation Heat Treated
Published By Publication Date Number of Pages
SAE 2003-03-12 10
]]> This specification covers a magnesium alloy in the form of sand castings. These castings have been used typically for parts requiring a combination of light weight, high yield strength up to 300 degrees C and relatively high corrosion resistance, but usage is not limited to such applications.

]]> SAE MAM 2355E:2008 ?u=/product/publishers/sae/sae-mam-2355e2008/ Wed, 06 Nov 2024 05:01:52 +0000 Quality Assurance, Sampling and Testing, Aluminum Alloys and Magnesium Alloys, Wrought Products, Except Forging Stock, and Rolled, Forged, or Flash Welded Rings
Published By Publication Date Number of Pages
SAE 2008-01-03 15
]]> This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable specification requirements of wrought aluminum alloy and wrought magnesium alloy mill products, except forging stock, including rolled, forged, and flash welded rings, specified in metric (SI) units. Definitions of rings, as applicable to this specification, are presented in 8.3 (Definitions).

]]> SAE MAM 2205A:1996 ?u=/product/publishers/sae/sae-mam-2205a1996/ Wed, 06 Nov 2024 05:01:40 +0000 Tolerances, Metric, Aluminum Alloy and Magnesium Alloy Extrusions
Published By Publication Date Number of Pages
SAE 1996-08-01 1
]]> This specification covers established metric manufacturing tolerances applicable to aluminum alloy and magnesium alloy extruded bar, rod, wire, shapes, and tubing ordered to metric dimensions. Tolerances greater than standard may be necessary for some shapes; tolerances closer than standard may be possible for others. Tolerances shown herein, however, apply unless otherwise agreed upon by purchaser and vendor and apply to all tempers, unless otherwise noted.

]]> SAE MAM 2202C:1996 ?u=/product/publishers/sae/sae-mam-2202c1996/ Wed, 06 Nov 2024 05:01:39 +0000 Tolerances, Metric, Aluminum Alloy and Magnesium Alloy Sheet and Plate
Published By Publication Date Number of Pages
SAE 1996-08-01 1
]]> This specification covers established manufacturing tolerances applicable to aluminum alloy and magnesium alloy sheet and plate ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. These tables are based on logical metric values and preferred metric sizes. Throughout this specification, the term 'metric' is intended to refer to the SI system.

]]> SAE MA 4812A:2019 ?u=/product/publishers/sae/sae-ma-4812a2019/ Wed, 06 Nov 2024 05:01:27 +0000 Insert - Thin Wall, Metric Short and Long Hole Preparation for
Published By Publication Date Number of Pages
SAE 2019-03-18 3
]]> Insert - Thin Wall, Metric Short and Long Hole Preparation for
Published By Publication Date Number of Pages
SAE 2019-03-18 3
]]> SAE MA 3454B:2018 ?u=/product/publishers/sae/sae-ma-3454b2018/ Wed, 06 Nov 2024 05:00:58 +0000 Cover - Engine Accessory Drive, Square, 127.28 BC, Metric AMS4424 (UNS M11630) or AMS4484
Published By Publication Date Number of Pages
SAE 2018-09-17 3
]]> Cover - Engine Accessory Drive, Square, 127.28 BC, Metric AMS4424 (UNS M11630) or AMS4484
Published By Publication Date Number of Pages
SAE 2018-09-17 3
]]> SAE MA 3375D:2018 ?u=/product/publishers/sae/sae-ma-3375d2018/ Wed, 06 Nov 2024 05:00:33 +0000 Studs, Corrosion and Heat Resistant Steel, UNS S66286 Tensile Strength 900 MPa, Procurement Specification, Metric FSC 5307
Published By Publication Date Number of Pages
SAE 2018-05-16 18
]]>
This document covers metric studs made from a corrosion and heat resistant, age hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286. The following specification designations and their properties are covered:
]]> SAE J 993:2018 ?u=/product/publishers/sae/sae-j-9932018/ Wed, 06 Nov 2024 04:57:54 +0000 Alloy and Temper Designation Systems for Aluminum
Published By Publication Date Number of Pages
SAE 2018-01-09 12
]]>
This standard provides systems for designating wrought aluminum and wrought aluminum alloys, aluminum and aluminum alloys in the form of castings and foundry ingot, and the tempers in which aluminum and aluminum alloy wrought products and aluminum alloy castings are produced.
]]>