77.150.70 – Cadmium and cobalt products – PDF Standards Store

ASTM-B815:2024 Edition(Redline)

Sun, 20 Oct 2024 09:46:04 +0000

ASTM B815-24

Redline Standard: Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy Bar or Rod

ASTM B815

Scope

1.1 This specification2 covers cobalt-chromium-nickel-molybdenum-tungsten alloy in the form of bar or rod. While the alloy is typically used for wear applications and general corrosion service, it is not limited to this usage.

1.2 UNS R31233 is the only alloy currently allowed to be certified to this specification.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

bar; rod; R31233;

ICS Code

ICS Number Code 77.150.70 (Cadmium and cobalt products)

DOI: 10.1520/B0815-24

ASTM-B815:2024 Edition

Sun, 20 Oct 2024 09:46:04 +0000

ASTM B815-24

Active Standard: Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy Bar or Rod

ASTM B815

Scope

1.2 UNS R31233 is the only alloy currently allowed to be certified to this specification.

Keywords

bar; rod; R31233;

ICS Code

ICS Number Code 77.150.70 (Cadmium and cobalt products)

DOI: 10.1520/B0815-24

ASTM-B818:2018 Edition

Sat, 19 Oct 2024 11:49:00 +0000

ASTM B818-03-Reapproved2018

Active Standard: Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy(UNS R31233) Plate, Sheet and Strip

ASTM B818

Scope

1.1 This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rolled plate, sheet, and strip for wear applications and general corrosion service.

1.2 The following products are covered under this specification:

1.2.1 Sheet and Strip—Hot or cold rolled, annealed and descaled unless solution-annealing is performed in an atmosphere yielding a bright finish.

1.2.2 Plate—Hot rolled, solution-annealed, and descaled.

Keywords

plate; sheet; strip; R31233;

ICS Code

ICS Number Code 77.150.70 (Cadmium and cobalt products)

DOI: 10.1520/B0818-03R18

ASTM-B815:2016 Edition

Sat, 19 Oct 2024 09:29:41 +0000

ASTM B815-02-Reapproved2016

Historical Standard: Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy (UNS R31233) Rod

ASTM B815

Scope

1.1 This specification2 covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rod for wear applications and general corrosion service.

1.2 The following products are covered under this specification:

1.2.1 Rods ³/₁₆ to ³/₄ in. (9.76 to 19.05 mm) exclusive in diameter, hot or cold finished, solution-annealed, and pickled or mechanically descaled; and

1.2.2 Rods ³/₄ to 3¹/₂ in. (19.05 to 88.9 mm) inclusive in diameter, hot or cold finished, solution annealed, ground, or turned.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Keywords

rod; R31233;

ICS Code

ICS Number Code 77.150.70 (Cadmium and cobalt products)

DOI: 10.1520/B0815-02R16

ASTM-B712:2006 Edition

Sat, 19 Oct 2024 03:37:57 +0000

1.1 This guide describes procedures for use in conducting analysis of silver-cadmium oxide materials for sodium and potassium content. The exact methods for the performance of this testing are not stated since many different procedures are equally applicable. This guide points out specific procedures for decreasing the chance of recognized potential errors and specifies methods for increasing the sensitivity of the testing.

This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. For specific precautions see Sections 4 and 6.

1.2 Whoever uses this standard should consult the Material Safety Data Sheet concerning the products involved.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Significance and Use Precautions Sampling Procedures
2	Report Precision Keywords TABLE 1 TABLE 2

ASTM-B781:2006 Edition

Sat, 19 Oct 2024 03:35:59 +0000

1.1 This guide provides guidelines for users and manufacturers of silver-cadmium oxide material produced in strip, rod, wire, and part form for electrical contact applications.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices , and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology Significance and Use Manufacture
2	Chemical Composition Other Properties Sampling and Inspection TABLE 1
3	Rejection and Rehearing Keywords TABLE 2
4	TABLE 3

ASTM-B815:2006 Edition

Sat, 19 Oct 2024 03:34:57 +0000

1.1 This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rod for wear applications and general corrosion service.

1.2 The following products are covered under this specification:

1.2.1 Rods 3/16 to 3/4 in. (9.76 to 19.05 mm) exclusive in diameter, hot or cold finished, solution-annealed, and pickled or mechanically descaled; and

1.2.2 Rods 3/4 to 31/2 in. (19.05 to 88.9 mm) inclusive in diameter, hot or cold finished, solution annealed, ground, or turned.

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology Ordering Information Chemical Composition Mechanical Properties and Other Requirements Dimensions, Mass, and Permissible Variations
2	Workmanship, Finish, and Appearance Sampling Number of Tests and Retests Specimen Preparations Test Methods TABLE 1 TABLE 2 TABLE 3
3	Inspection Rejection and Rehearing Certification Product Marking Keywords X1. HEAT TREATMENT X1.1 TABLE 4

ASTM-B818:2008 Edition

Sat, 19 Oct 2024 03:34:52 +0000

1.1 This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rolled plate, sheet, and strip for wear applications and general corrosion service.

1.2 The following products are covered under this specification:

1.2.1 Sheet and Strip Hot or cold rolled, annealed and descaled unless solution-annealing is performed in an atmosphere yielding a bright finish.

1.2.2 Plate Hot rolled, solution-annealed, and descaled.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology General Requirements Ordering Information Chemical Composition Mechanical Properties and Other Requirements Dimensions, Mass, and Permissible Variations
2	Product Marking Keywords X1. HEAT TREATMENT X1.1 TABLE 1 TABLE 2

ASTM-B818:2013 Edition

Fri, 18 Oct 2024 08:44:22 +0000

1.1 This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rolled plate, sheet, and strip for wear applications and general corrosion service.

1.2 The following products are covered under this specification:

1.2.1 Sheet and Strip Hot or cold rolled, annealed and descaled unless solution-annealing is performed in an atmosphere yielding a bright finish.

1.2.2 Plate Hot rolled, solution-annealed, and descaled.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

ASTM-B818:1998 Edition

Fri, 18 Oct 2024 08:32:43 +0000

1.1 This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rolled plate, sheet, and strip for wear applications and general corrosion service.

1.2 The following products are covered under this specification:

1.2.1 Sheet and Strip -Hot or cold rolled, annealed and descaled unless solution-annealing is performed in an atmosphere yielding a bright finish.

1.2.2 Plate -Hot rolled, solution-annealed, and descaled.

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.