1.1 These test methods determine the ability of window assemblies of various types to restrain, delay, or frustrate forced entry.<\/p>\n
1.2 For purposes of these test methods, window assemblies are defined as described in and as shown in . Window assemblies with a combination of operable sash and fixed panes (lites) shall be classified and tested separately for each type.<\/p>\n
1.2.1 Type AA window assembly which incorporates one or more sash that open by sliding<\/i> , either vertically or horizontally within the plane of the wall.<\/p>\n
1.2.2 Type BA window assembly which incorporates one or more sash that are hinged<\/i> at or near two corners of the sash and that open toward the exterior (outswinging) or toward the interior (inswinging).<\/p>\n
1.2.3 Type CA window assembly which incorporates one or more sash that are pivoted<\/i> so that part of the sash opens toward the interior and part of it opens toward the exterior.<\/p>\n
1.2.4 Type DA window assembly which incorporates one or more fixed<\/i> panes (lites) or stationary sash that are designed not to open.<\/p>\n
Note 1See for graphic depiction of window assembly types.<\/p>\n
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.<\/p>\n
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | Scope Referenced Documents Terminology Summary of Test Method <\/td>\n<\/tr>\n | ||||||
| 2<\/td>\n | FIG. 1 <\/td>\n<\/tr>\n | ||||||
| 3<\/td>\n | Significance and Use Test Criteria Apparatus Hazards <\/td>\n<\/tr>\n | ||||||
| 4<\/td>\n | Preparation Procedure Report Precision and Bias Keywords <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | A1. SUGGESTED MEASURED PERFORMANCE A2. TESTS A2.1 Disassembly Test A2.2 Lock Hardware Manipulation Test A2.3 Sash Manipulation Test A2.4 Type A Window Assembly Tests TABLE A1.1 FIG. A2.1 <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | FIG. A2.2 FIG. A2.3 FIG. A2.4 FIG. A2.5 <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | FIG. A2.6 FIG. A2.7 FIG. A2.8 FIG. A2.9 FIG. A2.10 <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | A2.5 Type B Window Assembly Tests A2.6 Type C Window Assembly Tests FIG. A2.11 FIG. A2.12 FIG. A2.13 FIG. A2.14 <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | A2.7 Type D Window Assemblies FIG. A2.15 FIG. A2.16 FIG. A2.17 FIG. A2.18 FIG. A2.19 <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | X1. BACKGROUND INFORMATION X1.1 X1.2 X1.3 X1.4 X1.5 FIG. A2.20 <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" F588-04 Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies, Excluding Glazing Impact<\/b><\/p>\n |