This standard describes 3-in. through 64-in. (80-mm through 1,600-mm) ductile-iron compact fittings to be used with ductile-iron pipe or pipe made of other materials with similar outside diameters for conveying potable water, wastewater, and reclaimed water. Fittings with mechanical joints are listed in this standard for the 3-in. through 64-in. (80-mm through 1,600-mm) sizes. Fittings with push-on joints and flanged joints are listed in this standard for the 54-in. through 64-in. (1,400-mm through 1,600-mm) sizes.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 12<\/td>\n | II.C.\tConnecting Fittings and Aged Cast-iron Pipe.\u2003Fittings should be connected carefully to aged existing cast-iron pipe. The outside diameter of aged pipe should be measured before cutting because some older pipe was manufactured to a larger diameter th <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | II.D.\tAdvisory Information on Product Testing.\u2003The standard acceptance test for static castings is a tensile test from a coupon cast from the same iron. This is typically done with a separately cast ASTM A536 keel block, a modified keel block, or a Y-bloc II.E.\tAdvisory Information for the Purchaser and Specifier.\u2003Purchasers and specifiers should be aware that although products may be available that meet the intent of this standard, they may vary in dimensions, characteristics, material properties, or othe II.F.\tChlorine and Chloramine Degradation of Elastomers.\u2003The selection of materials is critical for water service and distribution piping in locations where there is a possibility that elastomers will be in contact with chlorine or chloramines. Documented <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | IV.\tMajor Revisions.\u2003The major revisions in this edition of ANSI\/AWWA C153\/A21.53 are as follows: III.\tUse of This Standard.\u2003It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular application being considered. III.A.\tPurchaser Options and Alternatives.\u2003The following items should be provided by the purchaser: III.B.\tModification to Standard.\u2003Any modification of the provisions, definitions, or terminology in this standard must be provided by the purchaser. <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | V.\tComments.\u2003If you have any comments or questions about this standard, please call AWWA Engineering and Technical Services at 303.794.7711, FAX at 303.795.7603, write to the department at 6666 West Quincy Avenue, Denver, CO 80235-3098, or e-mail at stand <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | AWWA Standard SECTION 1:\u2002GENERAL Sec.\u20021.1\tScope <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | Sec.\u20021.2\tPurpose Sec.\u20021.3\tApplication SECTION 1:\u2002REFERENCES <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | SECTION 1:\u2002DEFINITIONS <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | SECTION 1:\u2002REQUIREMENTS Sec.\u20024.1\tMaterials Sec.\u20024.2\tPermeation Sec.\u20024.3\tGeneral Requirements <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | Sec.\u20024.4\tCoatings and Linings <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | Sec.\u20024.5\tTolerances or Permitted Variations <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | Sec.\u20024.6\tMarkings on Fittings Sec.\u20024.7\tSpecial Requirements for Flanged Fittings <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | SECTION 5:\u2002VERIFICATION Sec.\u20025.1\tInspection <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | Sec.\u20025.2\tTest Procedures <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | Sec.\u20025.4\tAdditional Tests Required by Purchaser Sec.\u20025.5\tPerformance Requirements Sec.\u20025.6\tDefective Specimens and Retests Sec.\u20025.7\tNonconforming Fittings <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | SECTION 6:\u2002DELIVERY <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" AWWA C153-19 Ductile-Iron Compact Fittings<\/b><\/p>\n |