This International Standard specifies basic requirements for the installation of media for communication networks in industrial premises and within and between the automation islands, of industrial sites. This standard covers balanced and optical fibre cabling. It also covers the cabling infrastructure for wireless media, but not the wireless media itself. Additional media are covered in the IEC 61784-5 series.<\/p>\n
This standard is a companion standard to the communication networks of the industrial automation islands and especially to the communication networks specified in the IEC 61158 series and the IEC 61784 series. In addition, this standard covers:<\/p>\n
the installation of generic telecommunication cabling for industrial premises as specified in ISO\/IEC 24702;<\/p>\n<\/li>\n
the connection between the generic telecommunications cabling specified in ISO\/IEC 24702 and the specific communication cabling of an automation island, where an automation outlet (AO) replaces the telecommunication outlet (TO) of ISO\/IEC 24702.<\/p>\n<\/li>\n<\/ul>\n
\nNOTE If the interface used at the AO does not conform to that specified for the TO of ISO\/IEC 24702, the cabling no longer conforms to ISO\/IEC 24702 although certain features, including performance, of generic cabling may be retained.<\/p>\n<\/blockquote>\n
This standard provides guidelines that cope with the critical aspects of the industrial automation area (safety, security and environmental aspects such as mechanical, liquid, particulate, climatic, chemicals and electromagnetic interference).<\/p>\n
This standard does not recognise implementations of power distribution through Ethernet balanced cabling systems that are not specified in IEEE 802.3 and in IEEE 802.3at.<\/p>\n
This standard deals with the roles of planner, installer, verifier, and acceptance test personnel, administration and maintenance personnel and specifies the relevant responsibilities and\/or gives guidance.<\/p>\n
PDF Catalog<\/h4>\n
\n
\n PDF Pages<\/th>\n PDF Title<\/th>\n<\/tr>\n \n 4<\/td>\n Foreword <\/td>\n<\/tr>\n \n 5<\/td>\n Endorsement notice
COMMON MODIFICATIONS
Figure 2 – Network installation: Standards relationships at European level <\/td>\n<\/tr>\n\n 11<\/td>\n English
CONTENTS <\/td>\n<\/tr>\n\n 19<\/td>\n INTRODUCTION <\/td>\n<\/tr>\n \n 20<\/td>\n Figures
Figure 1 \u2013 Industrial network installation life cycle <\/td>\n<\/tr>\n\n 21<\/td>\n Figure 2 \u2013 Standards relationships <\/td>\n<\/tr>\n \n 22<\/td>\n 1 Scope
2 Normative references <\/td>\n<\/tr>\n\n 25<\/td>\n 3 Terms, definitions, and abbreviated terms
3.1 Terms and definitions <\/td>\n<\/tr>\n\n 35<\/td>\n 3.2 Abbreviated terms <\/td>\n<\/tr>\n \n 37<\/td>\n 3.3 Conventions for installation profiles
4 Installation planning
4.1 General
4.1.1 Objective
4.1.2 Cabling in industrial premises <\/td>\n<\/tr>\n\n 38<\/td>\n Figure 3 \u2013 Structure of generic cabling connected to an automation island
Figure 4 \u2013 Automation island cabling attached to elements of generic cabling <\/td>\n<\/tr>\n\n 39<\/td>\n Figure 5 \u2013 Automation islands
Figure 6 \u2013 Automation island network external connections <\/td>\n<\/tr>\n\n 40<\/td>\n 4.1.3 The planning process <\/td>\n<\/tr>\n \n 41<\/td>\n 4.1.4 Specific requirements for CPs
4.1.5 Specific requirements for generic cabling in accordance with ISO\/IEC\u00a024702
4.2 Planning requirements
4.2.1 Safety
4.2.2 Security <\/td>\n<\/tr>\n\n 42<\/td>\n 4.2.3 Environmental considerations and EMC <\/td>\n<\/tr>\n \n 43<\/td>\n 4.2.4 Specific requirements for generic cabling in accordance with ISO\/IEC\u00a024702
4.3 Network capabilities
4.3.1 Network topology
Figure 7 \u2013 How to meet environmental conditions
Figure 8 \u2013 How enhancement, isolation and separation work together <\/td>\n<\/tr>\n\n 44<\/td>\n Figure 9 \u2013 Basic physical topologies for passive networks
Figure 10 \u2013 Basic physical topologies for active networks <\/td>\n<\/tr>\n\n 45<\/td>\n 4.3.2 Network characteristics
Figure 11 \u2013 Example of combination of basic topologies <\/td>\n<\/tr>\n\n 46<\/td>\n Tables
Table 1 \u2013 Basic network characteristics for balanced cabling not based on Ethernet <\/td>\n<\/tr>\n\n 47<\/td>\n Table 2 \u2013 Network characteristics for balanced cabling based on Ethernet <\/td>\n<\/tr>\n \n 48<\/td>\n Table 3 \u2013 Network characteristics for optical fibre cabling <\/td>\n<\/tr>\n \n 49<\/td>\n 4.4 Selection and use of cabling components
4.4.1 Cable selection <\/td>\n<\/tr>\n\n 50<\/td>\n Table 4 \u2013 Information relevant to copper cable: fixed cables <\/td>\n<\/tr>\n \n 51<\/td>\n Table 5 \u2013 Information relevant to copper cable: cords <\/td>\n<\/tr>\n \n 52<\/td>\n Table 6 \u2013 Information relevant to optical fibre cables <\/td>\n<\/tr>\n \n 53<\/td>\n 4.4.2 Connecting hardware selection <\/td>\n<\/tr>\n \n 54<\/td>\n Table 7 \u2013 Connectors for balanced cabling CPs based on Ethernet
Table 8 \u2013 Connectors for copper cabling CPs not based on Ethernet
Table 9 \u2013 Optical fibre connecting hardware <\/td>\n<\/tr>\n\n 55<\/td>\n 4.4.3 Connections within a channel\/permanent link
Table 10 \u2013 Relationship between FOC and fibre types (CP x\/y) <\/td>\n<\/tr>\n\n 56<\/td>\n Figure 12 \u2013 Basic reference implementation model <\/td>\n<\/tr>\n \n 57<\/td>\n Table 11 \u2013 Basic reference implementation formulas <\/td>\n<\/tr>\n \n 58<\/td>\n Figure 13 \u2013 Enhanced reference implementation model
Table 12 \u2013 Enhanced reference implementation formulas <\/td>\n<\/tr>\n\n 59<\/td>\n Table 13 \u2013 Correction factor Z for operating temperature above 20\u00a0\u00b0C <\/td>\n<\/tr>\n \n 61<\/td>\n 4.4.4 Terminators <\/td>\n<\/tr>\n \n 62<\/td>\n 4.4.5 Device location and connection
4.4.6 Coding and labelling
4.4.7 Earthing and bonding of equipment and devices and shielded cabling <\/td>\n<\/tr>\n\n 64<\/td>\n Table 14 \u2013 Equalisation and earthing conductor sizing and length <\/td>\n<\/tr>\n \n 65<\/td>\n Figure 14 \u2013 Selection of the earthing and bonding systems <\/td>\n<\/tr>\n \n 66<\/td>\n Table\u00a015 \u2013 Bonding straps cross-section
Table 16 \u2013 Bonding plates surface protection <\/td>\n<\/tr>\n\n 67<\/td>\n Figure\u00a015 \u2013 Wiring for bonding and earthing in an equipotential configuration <\/td>\n<\/tr>\n \n 68<\/td>\n Figure\u00a016 \u2013 Wiring of the earths in a star earthing configuration <\/td>\n<\/tr>\n \n 69<\/td>\n Figure\u00a017 \u2013 Schematic diagram of a field device with direct earthing <\/td>\n<\/tr>\n \n 70<\/td>\n Figure\u00a018 \u2013 Schematic diagram of a field device with parallel RC circuit earthing <\/td>\n<\/tr>\n \n 72<\/td>\n 4.4.8 Storage and transportation of cables
4.4.9 Routing of cables <\/td>\n<\/tr>\n\n 74<\/td>\n 4.4.10 Separation of circuits <\/td>\n<\/tr>\n \n 75<\/td>\n 4.4.11 Mechanical protection of cabling components
Table 17 \u2013 Cable circuit types and minimum distances <\/td>\n<\/tr>\n\n 76<\/td>\n 4.4.12 Installation in special areas
4.5 Cabling planning documentation
4.5.1 Common description
4.5.2 Cabling planning documentation for CPs <\/td>\n<\/tr>\n\n 77<\/td>\n 4.5.3 Network certification documentation
4.5.4 Cabling planning documentation for generic cabling in accordance with ISO\/IEC\u00a024702
4.6 Verification of cabling planning specification
5 Installation implementation
5.1 General requirements
5.1.1 Common description
5.1.2 Installation of CPs
5.1.3 Installation of generic cabling in industrial premises
5.2 Cable installation
5.2.1 General requirements for all cabling types <\/td>\n<\/tr>\n\n 78<\/td>\n Table 18 \u2013 Parameters for balanced cables
Table 19 \u2013 Parameters for silica optical fibre cables
Table 20 \u2013 Parameters for POF optical fibre cables <\/td>\n<\/tr>\n\n 79<\/td>\n Figure\u00a019 \u2013 Insert edge protector
Table 21 \u2013 Parameters for hard clad silica optical fibre cables <\/td>\n<\/tr>\n\n 80<\/td>\n Figure 20 \u2013 Use an uncoiling device and avoid forming loop
Figure 21 \u2013 Avoid torsion <\/td>\n<\/tr>\n\n 81<\/td>\n Figure 22 \u2013 Maintain minimum bending radius
Figure 23 \u2013 Do not pull by the individual wires
Figure 24 \u2013 Use cable clamps with a large (wide) surface <\/td>\n<\/tr>\n\n 82<\/td>\n Figure 25 \u2013 Cable gland with bending protection
Figure 26 \u2013 Spiral tube <\/td>\n<\/tr>\n\n 84<\/td>\n 5.2.2 Installation and routing <\/td>\n<\/tr>\n \n 85<\/td>\n 5.2.3 Specific requirements for CPs
5.2.4 Specific requirements for wireless installation
5.2.5 Specific requirements for generic cabling in accordance with ISO\/IEC\u00a024702
5.3 Connector installation
5.3.1 Common description
Figure 27 \u2013 Separate cable pathways <\/td>\n<\/tr>\n\n 86<\/td>\n 5.3.2 Shielded connectors
5.3.3 Unshielded connectors
5.3.4 Specific requirements for CPs
5.3.5 Specific requirements for wireless installation
5.3.6 Specific requirements for generic cabling in accordance with ISO\/IEC\u00a024702
5.4 Terminator installation
5.4.1 Common description <\/td>\n<\/tr>\n\n 87<\/td>\n 5.4.2 Specific requirements for CPs
5.5 Device installation
5.5.1 Common description
5.5.2 Specific requirements for CPs
5.6 Coding and labelling
5.6.1 Common description
5.6.2 Specific requirements for CPs
5.7 Earthing and bonding of equipment and devices and shield cabling
5.7.1 Common description <\/td>\n<\/tr>\n\n 88<\/td>\n 5.7.2 Bonding and earthing of enclosures and pathways
Figure 28 \u2013 Use of flexible bonding straps at movable metallic pathways <\/td>\n<\/tr>\n\n 89<\/td>\n 5.7.3 Earthing methods
Figure 29 \u2013 Surface preparation for earthing and bonding electromechanical connections <\/td>\n<\/tr>\n\n 90<\/td>\n Figure 30 \u2013 Example of isolated bus bar <\/td>\n<\/tr>\n \n 91<\/td>\n 5.7.4 Shield earthing methods
Figure 31 \u2013 Example of isolator for mounting DIN rails
Figure 32 \u2013 Parallel RC shield earthing <\/td>\n<\/tr>\n\n 92<\/td>\n Figure 33 \u2013 Direct shield earthing
Figure 34 \u2013 Examples for shielding application <\/td>\n<\/tr>\n\n 93<\/td>\n 5.7.5 Specific requirements for CPs
5.7.6 Specific requirements for generic cabling in accordance with ISO\/IEC\u00a024702
5.8 As-implemented cabling documentation
Figure 35 \u2013 Voltage offset mitigation
Figure\u00a036 \u2013 First example of derivatives of shield earthing
Figure\u00a037 \u2013 Second example of derivatives of shield earthing <\/td>\n<\/tr>\n\n 94<\/td>\n 6 Installation verification and installation acceptance test
6.1 General
6.2 Installation verification
6.2.1 General <\/td>\n<\/tr>\n\n 95<\/td>\n 6.2.2 Verification according to cabling planning documentation
Figure 38 \u2013 Installation verification process <\/td>\n<\/tr>\n\n 96<\/td>\n 6.2.3 Verification of earthing and bonding
Figure 39 \u2013 Test of earthing connections <\/td>\n<\/tr>\n\n 97<\/td>\n 6.2.4 Verification of shield earthing
6.2.5 Verification of cabling system
6.2.6 Cable selection verification <\/td>\n<\/tr>\n\n 98<\/td>\n 6.2.7 Connector verification
6.2.8 Connection verification <\/td>\n<\/tr>\n\n 99<\/td>\n 6.2.9 Terminators verification
Figure 40 \u2013 Pin and pair grouping assignments for two eight position IEC\u00a060603-7 subparts and four position IEC\u00a060603 series to IEC\u00a061076-2-101 connectors
Figure 41 \u2013 Two pair 8-way modular connector
Figure 42 \u2013 Transposed pairs, split pairs and reversed pair <\/td>\n<\/tr>\n\n 100<\/td>\n 6.2.10 Coding and labelling verification
6.2.11 Verification report
6.3 Installation acceptance test
6.3.1 General <\/td>\n<\/tr>\n\n 101<\/td>\n Figure 43 \u2013 Validation process <\/td>\n<\/tr>\n \n 102<\/td>\n 6.3.2 Acceptance test of Ethernet-based cabling
Figure 44 \u2013 Schematic representation of the channel
Figure 45 \u2013 Schematic representation of the permanent link <\/td>\n<\/tr>\n\n 104<\/td>\n 6.3.3 Acceptance test of non-Ethernet-based cabling <\/td>\n<\/tr>\n \n 105<\/td>\n 6.3.5 Acceptance test report
7 Installation administration
7.1 General <\/td>\n<\/tr>\n\n 106<\/td>\n 7.2 Fields covered by the administration
7.3 Basic principles for the administration system
7.4 Working procedures <\/td>\n<\/tr>\n\n 107<\/td>\n 7.5 Device location labelling
7.6 Component cabling labelling <\/td>\n<\/tr>\n\n 108<\/td>\n 7.7 Documentation
7.8 Specific requirements for administration
8 Installation maintenance and installation troubleshooting
8.1 General <\/td>\n<\/tr>\n\n 109<\/td>\n 8.2 Maintenance
8.2.1 Scheduled maintenance <\/td>\n<\/tr>\n\n 110<\/td>\n Figure 46 \u2013 Communication network maintenance <\/td>\n<\/tr>\n \n 111<\/td>\n 8.2.2 Condition-based maintenance
8.2.3 Corrective maintenance
8.3 Troubleshooting
8.3.1 General description <\/td>\n<\/tr>\n\n 112<\/td>\n 8.3.2 Evaluation of the problem
8.3.3 Typical problems <\/td>\n<\/tr>\n\n 113<\/td>\n Table 22 \u2013 Typical problems in a network with balanced cabling <\/td>\n<\/tr>\n \n 114<\/td>\n Table 23 \u2013 Typical problems in a network with optical fibre cabling <\/td>\n<\/tr>\n \n 115<\/td>\n 8.3.4 Troubleshooting procedure
Figure 47 \u2013 Troubleshooting procedure <\/td>\n<\/tr>\n\n 116<\/td>\n 8.3.5 Simplified troubleshooting procedure
Figure 48 \u2013 Fault detection without special tools <\/td>\n<\/tr>\n\n 117<\/td>\n 8.4 Specific requirements for maintenance and troubleshooting <\/td>\n<\/tr>\n \n 118<\/td>\n Annex A (informative) Overview of generic cabling for industrial premises <\/td>\n<\/tr>\n \n 119<\/td>\n Annex B (informative) MICE description methodology
Figure B.1 \u2013 MICE classifications <\/td>\n<\/tr>\n\n 120<\/td>\n Figure\u00a0B.2 \u2013 Example MICE classifications within a facility
Figure B.3 \u2013 Enhancement, isolation and separation <\/td>\n<\/tr>\n\n 121<\/td>\n Figure B.4 \u2013 Example 1 of mitigation
Table B.2 \u2013 Example 2 of targeted MICE area
Table\u00a0B.1 \u2013 Example 1 of targeted MICE area <\/td>\n<\/tr>\n\n 122<\/td>\n Figure B.5 \u2013 Example 2 of mitigation
Figure B.6 \u2013 Frequency range of electromagnetic disturbance from common industrial devices <\/td>\n<\/tr>\n\n 123<\/td>\n Table B.3 \u2013 Relationship between electromagnetic disturbance-generating devices and \u201cE\u201d classification <\/td>\n<\/tr>\n \n 124<\/td>\n Figure B.7 \u2013 Example of a general guidance for separation versus EFT value
Table B.4 \u2013 Coupling mechanism for some interfering devices <\/td>\n<\/tr>\n\n 125<\/td>\n Table B.5 \u2013 MICE definition <\/td>\n<\/tr>\n \n 127<\/td>\n Annex C (informative) Network topologies <\/td>\n<\/tr>\n \n 129<\/td>\n Annex D (informative) Connector tables
Table D.1 \u2013 Conventions for colour code used in the connector table <\/td>\n<\/tr>\n\n 130<\/td>\n Table D.2 \u2013 Pair numbers and colour scheme <\/td>\n<\/tr>\n \n 131<\/td>\n Table D.3 \u2013 8-way modular connector <\/td>\n<\/tr>\n \n 132<\/td>\n Table D.4 \u2013 M12-4 A-coding connector <\/td>\n<\/tr>\n \n 133<\/td>\n Table D.5 \u2013 M12-4 D-coding connector <\/td>\n<\/tr>\n \n 134<\/td>\n Table D.6 \u2013 M12-5 A-coding connector <\/td>\n<\/tr>\n \n 135<\/td>\n Table D.7 \u2013 M12-5 B-coding connector <\/td>\n<\/tr>\n \n 136<\/td>\n Table D.8 \u2013 SubD connector <\/td>\n<\/tr>\n \n 137<\/td>\n Table D.9 \u2013 7\/8-16\u00a0UN-2B THD\u00a0\/ M18\u00a0connector <\/td>\n<\/tr>\n \n 138<\/td>\n Table D.10 \u2013 Open style connector <\/td>\n<\/tr>\n \n 139<\/td>\n Table D.11 \u2013 M12-8 X-coding connector <\/td>\n<\/tr>\n \n 140<\/td>\n Table D.12 \u2013 BNC connector <\/td>\n<\/tr>\n \n 141<\/td>\n Table D.13 \u2013 TNC connector <\/td>\n<\/tr>\n \n 142<\/td>\n Annex E (informative) Power networks with respect to electromagnetic interference \u2013TN-C and TN-S approaches
Figure E.1 \u2013 Four-wire power network (TN-C) <\/td>\n<\/tr>\n\n 143<\/td>\n Figure E.2 \u2013 Five wire power network (TN-S) <\/td>\n<\/tr>\n \n 144<\/td>\n Annex F (informative) Conductor sizes in electrical cables
Table F.1 \u2013 American wire gauge system and kcmil <\/td>\n<\/tr>\n\n 146<\/td>\n Annex G (informative) Installed cabling verification checklists
Table G.1 \u2013 Copper cabling verification checklist <\/td>\n<\/tr>\n\n 148<\/td>\n Table G.2 \u2013 Earthing and bonding measurements checklist
Table G.3 \u2013 Signatures for Table G.1 and Table G.2 checklists <\/td>\n<\/tr>\n\n 149<\/td>\n Table G.4 \u2013 Checklist for special checks for non-Ethernet base CPs
Table G.5 \u2013 Signatures for Table G.4 checklist <\/td>\n<\/tr>\n\n 150<\/td>\n Table G.6 \u2013 Optical fibre cabling verification checklist
Table G.7 \u2013 Signatures for Table G.6 checklist <\/td>\n<\/tr>\n\n 151<\/td>\n Annex H (normative) Cord sets
Figure\u00a0H.1 \u2013 Straight through cord sets with M12-4 D-coding connectors <\/td>\n<\/tr>\n\n 152<\/td>\n Figure\u00a0H.2 \u2013 Straight through cord sets with 8-way modular connectors, 8 poles
Table H.1 \u2013 M12-4 D-coding pin\/pair assignment
Table H.2 \u2013 M12-4 D-coding to M12-4 D-coding crossover pin\/pair assignment <\/td>\n<\/tr>\n\n 153<\/td>\n Figure\u00a0H.3 \u2013 Straight through cord sets with 8-way modular connectors, 4 poles
Table H.3 \u2013 8-way modular pin\/pair assignment <\/td>\n<\/tr>\n\n 154<\/td>\n Table\u00a0H.4 \u2013 8-way modular crossover pin\/pair assignment
Table H.5 \u2013 Connectivity pin assignment <\/td>\n<\/tr>\n\n 155<\/td>\n Table H.6 \u2013 M12 to 8-way modular crossover pin pair assignment <\/td>\n<\/tr>\n \n 156<\/td>\n Annex I (informative) Guidance for terminating cable ends
Figure I.1 \u2013 Stripping the cable jacket <\/td>\n<\/tr>\n\n 157<\/td>\n Figure I.2 \u2013 Example of wire preparation for type A cables
Figure\u00a0I.3 \u2013 8-way modular plug <\/td>\n<\/tr>\n\n 158<\/td>\n Figure I.4 \u2013 Inserting the cable into the connector body
Figure I.5 \u2013 Crimping the connector <\/td>\n<\/tr>\n\n 159<\/td>\n Figure I.6 \u2013 Example of a cable preparation for type A wiring <\/td>\n<\/tr>\n \n 160<\/td>\n Figure I.7 \u2013 Connector components
Figure I.8 \u2013 Cable preparation
Figure I.9 \u2013 Connector wire gland, nut and shell on the cable
Figure I.10 \u2013 Conductors preparation <\/td>\n<\/tr>\n\n 161<\/td>\n Figure I.11 \u2013 Jacket removal
Figure I.12 \u2013 Shield preparation
Figure I.13 \u2013 Conductors preparation
Figure I.14 \u2013 Installing conductors in connector <\/td>\n<\/tr>\n\n 162<\/td>\n Figure I.15 \u2013 Assembling the body of the connector
Figure I.16 \u2013 Final assembling <\/td>\n<\/tr>\n\n 163<\/td>\n Annex J (informative) Recommendations for bulkhead connection performance and channel performance with more than 4 connections in the channel
Table J.1 \u2013 Transmission requirements for more than 4 connections in a channel <\/td>\n<\/tr>\n\n 164<\/td>\n Annex K (informative) Fieldbus data transfer testing <\/td>\n<\/tr>\n \n 168<\/td>\n Annex L (informative) Communication network installation work responsibility <\/td>\n<\/tr>\n \n 169<\/td>\n Annex M (informative) Trade names of communication profiles <\/td>\n<\/tr>\n \n 170<\/td>\n Table M.1 \u2013 Trade names of CPFs and CPs <\/td>\n<\/tr>\n \n 172<\/td>\n Annex N (informative) Validation measurements <\/td>\n<\/tr>\n \n 173<\/td>\n Figure N.1 \u2013 Loop resistance measurement wire to wire
Figure N.2 \u2013 Loop resistance measurement wire 1 to shield
Figure N.3 \u2013 Loop resistance measurement wire 2 to shield
Figure N.4 \u2013 Resistance measurement for detecting wire shorts <\/td>\n<\/tr>\n\n 174<\/td>\n Figure N.5 \u2013 Resistance measurement between wire 1 and wire 2 <\/td>\n<\/tr>\n \n 175<\/td>\n Figure N.6 \u2013 Validation of the cable DCR <\/td>\n<\/tr>\n \n 176<\/td>\n Figure N.7 \u2013 Conclusions for cable open or shorts <\/td>\n<\/tr>\n \n 177<\/td>\n Figure N.8 \u2013 Determination of proper cable terminator value <\/td>\n<\/tr>\n \n 178<\/td>\n Annex O (informative) End-to-end link
Figure O.1 \u2013 Channel according to ISO\/IEC 11801 <\/td>\n<\/tr>\n\n 179<\/td>\n Figure O.2 \u2013 End-to-end link <\/td>\n<\/tr>\n \n 181<\/td>\n Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Industrial communication networks. Installation of communication networks in industrial premises<\/b><\/p>\n
\n\n
\n Published By<\/td>\n Publication Date<\/td>\n Number of Pages<\/td>\n<\/tr>\n \n BSI<\/b><\/a><\/td>\n 2014<\/td>\n 184<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":244204,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[2641],"product_tag":[],"class_list":{"0":"post-244203","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-bsi","8":"first","9":"instock","10":"sold-individually","11":"shipping-taxable","12":"purchasable","13":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/244203","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/244204"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=244203"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=244203"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=244203"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}