{"id":252406,"date":"2024-10-19T16:39:50","date_gmt":"2024-10-19T16:39:50","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-60670-242013\/"},"modified":"2024-10-25T11:59:02","modified_gmt":"2024-10-25T11:59:02","slug":"bs-en-60670-242013","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-60670-242013\/","title":{"rendered":"BS EN 60670-24:2013"},"content":{"rendered":"

Replacement:<\/i><\/p>\n

This part of IEC 60670 applies to enclosures and parts of them for housing protective devices and other power dissipating electrical equipment intended to be used with a rated voltage not exceeding 400 V and a total incoming load current not exceeding 125 A for household and similar fixed electrical installations.<\/p>\n

These enclosures are intended to be installed where unskilled persons have access. They are intended to be integrated with electrical equipment on site by skilled persons (installers).<\/p>\n

They are intended to be installed where the prospective short circuit current does not exceed 10 kA unless they are protected by current limiting protective devices with a cut -off current not exceeding 17 kA.<\/p>\n

Enclosures complying with this standard are suitable for use, after installation, at ambient temperature not normally exceeding 25 \u00b0C, but occasionally reaching 35 \u00b0C over 24 h, max. 40 \u00b0C and min. \u20135 \u00b0C.<\/p>\n

An enclosure which is an integral part of an electrical accessory and provides protection against external influences (e.g. mechanical impacts, ingress of solid objects or of water), is covered by the relevant standard for such an accessory.<\/p>\n

This standard does not apply to a low-voltage switchgear and controlgear assembly (ASSEMBLY) as defined in the IEC 60439 or IEC 61439 series of standards nor to a main entrance panel which may or may not be part of the distribution board.<\/p>\n

\n

NOTE C A main entrance panel is a set composed by a panel or an enclosure equipped with a meter and\/or the main incoming device. Main entrance panels comply with their appropriate standards or the requiremen ts of the local supplier if any.<\/p>\n<\/blockquote>\n

PDF Catalog<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
6<\/td>\n1 Scope
2 Normative references
3 Definitions
7 Classification
8 Marking
12 Construction
13 Resistance to ageing, protection against ingress of solid foreign objects and against harmful ingress of water <\/td>\n<\/tr>\n
7<\/td>\n17 Creepage distances, clearances and distances through sealing compound
101 Verification of the maximum capability to dissipate power (Pde) <\/td>\n<\/tr>\n
8<\/td>\nAnnex ZA (normative) Normative references to international publications with their corresponding European publications <\/td>\n<\/tr>\n
9<\/td>\nAnnex ZB (normative) Special national conditions <\/td>\n<\/tr>\n
10<\/td>\nAnnex ZC (informative) A-deviations <\/td>\n<\/tr>\n
11<\/td>\nEnglish
\n
CONTENTS <\/td>\n<\/tr>\n
13<\/td>\n1 Scope
2 Normative references <\/td>\n<\/tr>\n
14<\/td>\n3 Definitions <\/td>\n<\/tr>\n
15<\/td>\n4 General requirements
5 General notes on tests
6 Ratings
7 Classification
8 Marking
Tables
\n
Table 1 \u2013 Classification of boxes and enclosures <\/td>\n<\/tr>\n
17<\/td>\n9 Dimensions
10 Protection against electric shock <\/td>\n<\/tr>\n
18<\/td>\n11 Provisions for earthing
12 Construction <\/td>\n<\/tr>\n
19<\/td>\n13 Resistance to ageing, protection against ingress of solid foreign objects and against harmful ingress of water
14 Insulation resistance and electric strength
15 Mechanical strength
16 Resistance to heat
17 Creepage distances, clearances and distances through sealing compound <\/td>\n<\/tr>\n
20<\/td>\n18 Resistance of insulating material to abnormal heat and to fire
19 Resistance to tracking
Table 101 \u2013 Creepage distances, clearances and distances through sealing compound <\/td>\n<\/tr>\n
21<\/td>\n20 Resistance to corrosion
21 Electromagnetic compatibility
101 Verification of the maximum capability to dissipate power (Pde) <\/td>\n<\/tr>\n
22<\/td>\n102 Verification of temperature rise <\/td>\n<\/tr>\n
23<\/td>\nTable 102 \u2013 Diversity factor <\/td>\n<\/tr>\n
24<\/td>\nFigures
\n
Figure 101 \u2013 Arrangement for the verification of the maximum capabilityto dissipate power (Pde) and for verification of temperature rise
\nof surface type enclosures
Table 103 \u2013 Temperatures of accessible surfaces <\/td>\n<\/tr>\n
25<\/td>\nFigure 102 \u2013 Heating resistor for the verification of the maximum capability
\nto dissipate power (Pde) <\/td>\n<\/tr>\n
26<\/td>\nFigure 103 \u2013 Position of the resistor for enclosures designed orintended to be fitted with rail mounting modular accessories
\nand electrical equipment <\/td>\n<\/tr>\n
27<\/td>\nFigure 104 \u2013 Position of the resistor(s) for enclosures other than those designed
\nor intended to be fitted with rail mounting accessories and electrical equipment <\/td>\n<\/tr>\n
28<\/td>\nFigure 105 \u2013 Position of the resistor(s) for enclosures other than those designedor intended to be fitted with rail mounting accessories and electrical equipmentand allowing the mounting of several accessories and electrical equipment
\nin different positions <\/td>\n<\/tr>\n
29<\/td>\nAnnex AA (normative) Instructions to be given by the manufacturer of the GP enclosure
\nto the installer how to integrate accessories, and example of calculation <\/td>\n<\/tr>\n
31<\/td>\nTable AA.1 \u2013 Diversity factor <\/td>\n<\/tr>\n
32<\/td>\nTable AA.2 \u2013 Tests and verifications <\/td>\n<\/tr>\n
35<\/td>\nTable AA.3 \u2013 Calculation of Pdp <\/td>\n<\/tr>\n
36<\/td>\nTable AA.4 \u2013 Calculation of Pau <\/td>\n<\/tr>\n
37<\/td>\nAnnex BB (normative)Instructions to be given by the manufacturer of the PD enclosure
\nto the installer how to integrate accessories <\/td>\n<\/tr>\n
39<\/td>\nBibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Particular requirements for enclosures for housing protective devices and other power dissipating electrical equipment<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
BSI<\/b><\/a><\/td>\n2013<\/td>\n42<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":252411,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[507,2641],"product_tag":[],"class_list":{"0":"post-252406","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-29-120-10","7":"product_cat-bsi","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/252406","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/252411"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=252406"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=252406"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=252406"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}