| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
| 4<\/td>\n | CONTENTS <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | INTRODUCTION <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 1 Scope 2 Normative references 3 Terms, definitions and symbols 3.1 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 3.2 Symbols 4 Overview of Auto Loading Feeder 4.1 Overview and features of Auto Loading Feeder Figures Figure 1 \u2013 Specified dimensions for emboss taping for Auto Loading Feeder Tables Table 1 \u2013 Symbols used in figures and tables <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 4.2 Methods and mechanisms of automatically exposing the pockets in using Auto Loading Feeder Figure 2 \u2013 Operation and features when another tape is re-supplied automatically by the Auto Loading Feeder <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 5 Discussion items for requirements for emboss taping for Auto Loading Feeder 5.1 General 5.2 Required dimensions for the cover tape sealed positions <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 5.3 Required dimensions for the distance between the upper side of the carrier tape and the top surface of a component in using Auto Loading Feeder 5.4 Necessity of M1 and M2 as the cover tape sealed positions Table 2 \u2013 The cover tape sealed positions required for emboss taping for Auto Loading Feeder Table 3 \u2013 Distance between the upper side of the carrier tape and the top surface of a component required for emboss taping for Auto Loading Feeder <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 5.5 Necessity of K1 as the distance between the upper side of the carrier tape and the top surface of a component <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 5.6 Necessity of K2 as the recessed part in a cross-bar section Figure 3 \u2013 Example of a part of embossed carrier tape with a recessed part in a cross-bar section Figure 4 \u2013 Relationship between the cover tape and the exposure processing mechanism of the pocket <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 5.7 Necessity of K3 as the distance between the upper side of the recessed part in a cross-bar section and the top surface of a component Figure 5 \u2013 Relationship between the exposure processing mechanism of the pocket and convex of carrier tape <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 5.8 Sealing method for the cover tape 5.9 Dent of the cover tape over the pockets Figure 6 \u2013 Example dent of the cover tape over the pocket <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 5.10 Lower limit of peel-off strength of the cover tape 5.11 Adhesion of components on the cover tape 5.12 Bottom hole of pockets of the carrier tape <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 5.13 Maximum trailer length 5.14 Fixing the tail end of the carrier tape 6 Summary of the discussions: considered requirements and dimensions for emboss taping for Auto Loading Feeder 6.1 General <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | 6.2 Required dimensions for the cover tape sealed positions 6.3 Required dimensions for the distance between the upper side of the carrier tape and the top surface of a component 6.4 Required specifications for the sealing method of the cover tape 6.5 Required specifications for maximum trailer length 7 Possible problems for emboss taping for Auto Loading Feeder 7.1 General 7.2 Relationship between sealed positions of the cover tape and openings of the pockets Figure 7 \u2013 Leader part and trailer part <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | 7.3 Recessed part in a cross-bar section 7.4 Dot seals Figure 8 \u2013 Dimension B1 and sealed positions <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | 7.5 Thickness of embossed carrier tape Figure 9 \u2013 Example of dot seal <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | 7.6 Relationship between Auto Loading Feeder and tape camber specified in IEC 60286-3 Figure 10 \u2013 Relationship between embossed carrier tape thickness and component exposure process Figure 11 \u2013 Tape camber (top view) <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | Annex A (informative) Methods and mechanisms of automatically exposing pockets in using Auto Loading Feeder A.1 General A.2 Single-door method A.3 Double-door method Figure A.1 \u2013 Overview of the single-door method <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | Figure A.2 \u2013 Overview of the double-door method <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | Annex B (informative) Glossary Table B.1 \u2013 Glossary of mounter and feeder related terms <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Packaging of components for automatic handling – Packaging of surface mount components on continuous embossed tapes for Auto Loading Feeder<\/b><\/p>\n |