This part of ISO 19085 gives the safety requirements and measures for stationary manually loaded and unloaded: – cold presses, – hot presses, – bending presses, – edge\/face gluing presses, – membrane presses, – embossing presses, where pressing force is applied by hydraulic actuators pushing two flat or shaped surfaces against each other, hereinafter referred to as “machines”. It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE: For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. It is also applicable to machines fitted with one or more of the following devices\/additional working units, whose hazards have been dealt with: – Device for hot gluing – Device for high frequency gluing – Device for high frequency shaping – Automatic work-piece loading and unloading system – intermediate additional platens – work-piece extractor – work-piece clamping pressure beam – split moveable platens. The machines are designed to process work-pieces consisting of: – solid wood; – materials with similar characteristics to wood (see ISO 19085-1:2017, 3.2); – honeycomb. This part of ISO 19085 does not deal with any hazards related to: – specific devices that differ from the list above; – hot fluid heating systems internal to the machine other than electrical; – any hot fluid heating systems external to the machine; – operation of taking intermediate platens out and in again; – the combination of a single machine being used with any other machine (as part of a line). It is not applicable to: – frame presses; – membrane presses where the pressing force is applied by vacuum only; – presses for producing chipboard, fibreboard, OSB; – machines intended for use in potentially explosive atmosphere; – machines manufactured before the date of its publication as an international standard.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Annex ZA (informative)Relationship between this European Standard and the essential requirements of EU Directive 2006\/42\/EC aimed to be covered <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 1 Scope <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 2 Normative references <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 4 List of significant hazards <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | 5 Safety requirements and measures for controls 5.1 Safety and reliability of control systems 5.2 Control devices <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | 5.3 Start 5.4 Safe stops 5.4.1 General 5.4.2 Normal stop <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | 5.4.3 Operational stop 5.4.4 Emergency stop 5.5 Braking function of tool spindles 5.6 Mode selection 5.7 Spindle speed changing 5.7.1 Spindle speed changing by changing belts on the pulleys 5.7.2 Spindle speed changing by incremental speed change motor 5.7.3 Infinitely variable speed by frequency inverter 5.8 Failure of any power supply <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | 5.9 Manual reset control 5.10 Enabling control 5.11 Machine moving parts speed monitoring 5.12 Time delay 6 Safety requirements and measures for protection against mechanical hazards 6.1 Stability 6.1.1 General <\/td>\n<\/tr>\n | ||||||
| 32<\/td>\n | 6.1.2 Displaceable machines 6.2 Risk of break-up during operation 6.3 Tool holder and tool design 6.3.1 General 6.3.2 Spindle locking 6.3.3 Circular saw blade fixing devices <\/td>\n<\/tr>\n | ||||||
| 33<\/td>\n | 6.3.4 Flange dimensions for circular saw blades 6.4 Braking 6.4.1 Braking of tool spindles 6.4.2 Maximum run-down time 6.4.3 Brake release 6.5 Safeguards 6.5.1 Fixed guards 6.5.2 Interlocking moveable guards 6.5.3 Hold-to-run control 6.5.4 Two hand control 6.5.5 Electro-sensitive protective equipment (ESPE) 6.5.6 Pressure sensitive protective equipment (PSPE) <\/td>\n<\/tr>\n | ||||||
| 34<\/td>\n | 6.6 Prevention of access to moving parts 6.6.1 General 6.6.2 Guarding of tools 6.6.3 Guarding of drives 6.6.4 Guarding of shearing and\/or crushing zones <\/td>\n<\/tr>\n | ||||||
| 38<\/td>\n | 6.7 Impact hazard 6.8 Clamping devices <\/td>\n<\/tr>\n | ||||||
| 39<\/td>\n | 6.9 Measures against ejection 6.9.1 General 6.9.2 Guards materials and characteristics 6.10 Work-piece support and guides <\/td>\n<\/tr>\n | ||||||
| 40<\/td>\n | 7 Safety requirements and measures for protection against other hazards 7.1 Fire 7.2 Noise 7.2.1 Noise reduction at the design stage <\/td>\n<\/tr>\n | ||||||
| 41<\/td>\n | 7.2.2 Noise emission measurement and declaration 7.3 Emission of chips and dust <\/td>\n<\/tr>\n | ||||||
| 42<\/td>\n | 7.4 Electricity 7.4.1 General <\/td>\n<\/tr>\n | ||||||
| 43<\/td>\n | 7.4.2 Displaceable machines 7.5 Ergonomics and handling 7.6 Lighting 7.7 Pneumatics 7.8 Hydraulics 7.9 Electromagnetic compatibility 7.10 Laser 7.11 Static electricity 7.12 Errors of fitting 7.13 Isolation <\/td>\n<\/tr>\n | ||||||
| 44<\/td>\n | 7.14 Maintenance 7.15 Extreme temperatures 8 Information for use 8.1 Warning devices 8.2 Marking 8.2.1 General 8.2.2 Additional markings 8.3 Instruction handbook 8.3.1 General <\/td>\n<\/tr>\n | ||||||
| 45<\/td>\n | 8.3.2 Additional information <\/td>\n<\/tr>\n | ||||||
| 46<\/td>\n | Annex A (informative) Performance level required <\/td>\n<\/tr>\n | ||||||
| 47<\/td>\n | Annex B (normative) Tests for braking function <\/td>\n<\/tr>\n | ||||||
| 48<\/td>\n | Annex C (normative) Stability test for displaceable machines <\/td>\n<\/tr>\n | ||||||
| 49<\/td>\n | Annex D (normative) Impact test for guards <\/td>\n<\/tr>\n | ||||||
| 50<\/td>\n | Annex E (normative) Noise test code <\/td>\n<\/tr>\n | ||||||
| 56<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Woodworking machines. Safety – Presses<\/b><\/p>\n |