{"id":416999,"date":"2024-10-20T06:13:49","date_gmt":"2024-10-20T06:13:49","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-62150-22011-2\/"},"modified":"2024-10-26T11:35:04","modified_gmt":"2024-10-26T11:35:04","slug":"bs-en-62150-22011-2","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-62150-22011-2\/","title":{"rendered":"BS EN 62150-2:2011"},"content":{"rendered":"
This part of IEC 62150 specifies testing and measuring procedures for fibre optic transceivers for asynchronous-transfer-mode passive optical network (ATM-PON) systems recommended by ITU-T G.983.1. These testing procedures correspond to methods of examining whether the transceivers satisfy the performance specifications defined in IEC 62149-5. On the other hand, the measuring procedures correspond to methods of precise measurement for such transceivers. The receiver sections of these transceivers can handle burst signals. Therefore, some procedures described in this standard correspond to the burst signal transmission.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
6<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | INTRODUCTION <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | 1 Scope 2 Normative references 3 Abbreviations and symbols 3.1 Abbreviations <\/td>\n<\/tr>\n | ||||||
10<\/td>\n | 3.2 Symbols 4 Standard ambient conditions 5 Apparatus 5.1 Power supply Table 1 \u2013 Ambient conditions for carrying out measurements and tests <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 5.2 Optical power meter 5.3 Variable optical attenuator 5.4 Pulse pattern generator 5.5 Optical splitter 5.6 Oscilloscope 5.7 Optical jumper cable 5.8 BER detector 5.9 Reference Tx and reference Rx 5.10 Calibrated optical spectrum analyzer 5.11 Low-pass filter <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 5.12 Optical-to-electrical (O\/E) converter 6 Test sample 7 Testing and measuring procedures 7.1 Rx alarm function <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | Figures Figure 1 \u2013 Testing and measuring configuration for Rx alarm function <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 7.2 Tx shutdown function Figure 2 \u2013 Relation between receiver input power and alarm voltage <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 7.3 Mean launched power: Pmean Figure 3 \u2013 Testing and measuring configuration for transmitter shutdown function <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | Figure 4 \u2013 Testing and measuring configuration for mean launched power Figure 5 \u2013 Burst signal pattern <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 7.4 Centroidal wavelength and spectral width Figure 6 \u2013 Testing and measuring configuration for mean launched power <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | 7.5 Extinction ratio and mask test Figure 7 \u2013 Testing and measuring configuration for extinction ratio and mask test <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 7.6 Receiver sensitivity (S) and receiver overload (SO) <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | Figure 8 \u2013 Testing and measuring configuration for receiver sensitivity and overload <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | Figure 9 \u2013 Burst signal patterns for measurement <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | 8 Test result 8.1 Required information 8.2 Available information <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Fibre optic active components and devices. Test and measurement procedures – ATM-PON transceivers<\/b><\/p>\n |