IEC 63203-402-1:2022 specifies test methods for wearable glove-type motion sensors to measure finger movements. The measurement methods include goniometric parameters related to the finger postures and flexion dynamics. Glove-type motion sensors are the type of gloves considered within the scope of this document for testing and measurement. This document describes direct and indirect measurement methods. In the direct measurement method, the angles of the joints of each finger are directly measured by a goniometer. The indirect method uses a measurement device such as a servomotor-based angle-measuring device. This document is applicable to angle measurement of all gloves with glove-type motion sensors without limitation of the device technology or size.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Annex ZA (normative)Normative references to international publicationswith their corresponding European publications <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions 3.1 General terms <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 3.2 Angle between finger joints <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 4 Test conditions and method 4.1 Test conditions 4.2 Preparation of gloves under test 4.3 Test methods 4.3.1 Direct measurement test procedure: angle between finger joints Figures Figure 1 \u2013 Position of DIP, PIP, IP and MCP <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | Figure 2 \u2013 Direct measurement method using a manual goniometer <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 4.3.2 Indirect measurement test procedure: angle between finger joints with sensors Table 1 \u2013 Comparison of angle data measured with a glove sensor and goniometer <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | Figure 3 \u2013 Test setup based on the servomotor for sensor angle measurement Figure 4 \u2013 Test procedure of angle measurement inthe wearable glove based on the servomotor <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 5 Test report Table 2 \u2013 Comparison of angle data measured with a glove sensor and servomotor <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Annex A (informative)Glove-type motion sensors A.1 Glove-type motion sensors A.2 Examples by sensing type A.2.1 Schematic of a resistive-type glove sensor Figure A.1 \u2013 Examples of glove-type motion sensors Figure A.2 \u2013 Schematic of a resistive-type glove sensor <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | A.2.2 Schematic of a capacitive-type glove sensor A.2.3 Schematic of a piezoelectric-type glove sensor Figure A.3 \u2013 Schematic of a capacitive-type glove sensor Figure A.4 \u2013 Structure of a piezoelectric-type glove sensor <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Wearable electronic devices and technologies – Performance measurement of fitness wearables. Test methods of glove-type motion sensors for measuring finger movements<\/b><\/p>\n |