| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 8<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 1 Scope <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 2 Normative references <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | 4 Safety requirements and measures for controls 4.1 Safety and reliability of control systems 4.2 Control devices 4.2.1 General 4.2.2 Single end tenoning machines with manual feed sliding table 4.2.3 Single end tenoning machines with mechanical feed sliding table 4.2.4 Single end tenoning and\/or profiling machines with mechanical feed 4.2.5 Double end tenoning and\/or profiling machines with mechanical feed <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | 4.2.6 Angular systems for tenoning and profiling with mechanical feed 4.3 Start 4.3.1 Direct start 4.3.2 Start via control power-on <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | 4.3.3 Laser marking unit 4.4 Safe stops 4.4.1 General 4.4.2 Normal stop 4.4.3 Operational stop 4.4.4 Emergency stop 4.5 Braking function of tool spindles 4.6 Mode selection <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | 4.7 Tool speed changing 4.7.1 Speed changing by shifting the belts on the pulleys 4.7.2 Speed changing by incremental speed change motor 4.7.3 Infinitely variable speed by frequency inverter 4.8 Failure of any power supply 4.9 Manual reset control 4.10 Standstill detection and monitoring 4.11 Machine moving parts speed monitoring <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 4.12 Time delay 4.13 Teleservice 5 Safety requirements and measures for protection against mechanical hazards 5.1 Stability 5.2 Risk of break-up during operation 5.3 Tool and tool fixing design 5.3.1 General <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | 5.3.2 Spindle locking 5.3.3 Circular saw blade fixing device 5.3.4 Flange dimensions for circular saw blades 5.3.5 Spindle rings 5.4 Braking 5.4.1 Braking of tools 5.4.2 Maximum run-down time 5.4.3 Brake release <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | 5.5 Safeguards 5.5.1 Fixed guards 5.5.2 Interlocking moveable guards 5.5.3 Hold-to-run control 5.5.4 Two hand control 5.5.5 Electro-sensitive protective equipment (ESPE) 5.5.6 Pressure sensitive protective equipment (PSPE) 5.5.7 Enabling control 5.6 Prevention of access to hazardous moving parts 5.6.1 Single end tenoning machines with manual feed sliding table <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | 5.6.2 Single end tenoning machines with mechanical feed sliding table <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | 5.6.3 Single end tenoning and\/or profiling machines with mechanical feed <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | 5.6.4 Double end tenoning and\/or profiling machines with mechanical feed <\/td>\n<\/tr>\n | ||||||
| 35<\/td>\n | 5.6.5 Angular systems for tenoning and profiling with mechanical feed <\/td>\n<\/tr>\n | ||||||
| 36<\/td>\n | 5.6.6 Guarding of drives <\/td>\n<\/tr>\n | ||||||
| 37<\/td>\n | 5.6.7 Guarding of the chain or feed mechanisms <\/td>\n<\/tr>\n | ||||||
| 38<\/td>\n | 5.7 Impact hazard 5.8 Clamping devices 5.8.1 Single end tenoning machines with sliding table <\/td>\n<\/tr>\n | ||||||
| 39<\/td>\n | 5.8.2 Machines other than single end tenoning machines with sliding table 5.9 Measures against ejection 5.9.1 General 5.9.2 Guards materials and characteristics <\/td>\n<\/tr>\n | ||||||
| 40<\/td>\n | 5.9.3 Devices to minimize the possibility or effect of ejection or kickback <\/td>\n<\/tr>\n | ||||||
| 42<\/td>\n | 5.10 Workpiece support and guides 5.10.1 Single end tenoning machines with sliding table 5.10.2 Single end tenoning and\/or profiling machines with mechanical feed 5.10.3 Double end tenoning and\/or profiling machines with mechanical feed <\/td>\n<\/tr>\n | ||||||
| 43<\/td>\n | 5.10.4 Angular systems for tenoning and profiling with mechanical feed 5.10.5 Workpiece returner 6 Safety requirements and measures for protection against other hazards 6.1 Fire <\/td>\n<\/tr>\n | ||||||
| 44<\/td>\n | 6.2 Noise 6.2.1 Noise reduction at the design stage 6.2.2 Noise emission measurement 6.3 Emission of chips and dust 6.4 Electricity 6.5 Ergonomics and handling 6.6 Lighting 6.7 Pneumatics 6.8 Hydraulics <\/td>\n<\/tr>\n | ||||||
| 45<\/td>\n | 6.9 Electromagnetic compatibility 6.10 Laser 6.11 Static electricity 6.12 Errors of fitting 6.13 Isolation 6.14 Maintenance 6.15 Relevant but not significant hazards 6.16 Extreme temperatures 6.17 Substances <\/td>\n<\/tr>\n | ||||||
| 46<\/td>\n | 7 Information for use 7.1 Warning devices 7.2 Marking 7.2.1 General 7.2.2 Additional markings 7.3 Instruction handbook 7.3.1 General 7.3.2 Additional information <\/td>\n<\/tr>\n | ||||||
| 49<\/td>\n | Annex\u20acA (informative) List of significant hazards <\/td>\n<\/tr>\n | ||||||
| 51<\/td>\n | Annex\u20acB (informative) Performance levels required <\/td>\n<\/tr>\n | ||||||
| 53<\/td>\n | Annex\u20acC Stability test <\/td>\n<\/tr>\n | ||||||
| 54<\/td>\n | Annex\u20acD (normative) Test for braking function <\/td>\n<\/tr>\n | ||||||
| 55<\/td>\n | Annex\u20acE (normative) Impact test for guards <\/td>\n<\/tr>\n | ||||||
| 56<\/td>\n | Annex\u20acF (normative) Noise test code <\/td>\n<\/tr>\n | ||||||
| 64<\/td>\n | Annex\u20acZA (informative) Relationship between this European Standard and the essential requirements of Directive 2006\/42\/EC aimed to be covered <\/td>\n<\/tr>\n | ||||||
| 66<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" BS ENISO 19085-12 Woodworking machines. Safety – Part 12. Tenoning\/profiling machines<\/b><\/p>\n |