This Standard is intended to establish uniform practices for the measurement of master rings or ring gages using horizontal methods. The standard includes requirements for geometric qualities of master rings or ring gages, the important characteristics of the comparison equipment, environmental conditions, and the means to assure that measurements are made with an acceptable level of accuracy. This Standard does not include measurement methods for rings below 1 mm (0.040 in.). The measurement method on these very small rings should be agreed upon prior to manufacture or calibration between the manufacturer\/laboratory and customer.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 5<\/td>\n | CONTENTS FIGURES TABLES NONMANDATORY APPENDICES <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | COMMITTEE ROSTER <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | CORRESPONDENCE WITH THE B89 COMMITTEE <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 1 SCOPE 2 DEFINITIONS <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 3 REFERENCES <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 4 REQUIREMENTS OF MASTER RINGS AND RING GAGES 4.1 General 4.2 Design 4.3 Material 4.4 Surface Roughness 4.5 Geometric Requirements 4.5.1 General <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 4.5.2 Roundness 4.5.3 Straightness and Taper 4.6 Face Perpendicularity of Rings 4.7 Tolerance Classes 1 Surface Roughness Limits for Master Rings and Ring Gages <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 4.8 Identification 5 CALIBRATION OF AN IDENTIFIED DIAMETER 5.1 General 5.2 Location of Calibrated Diameter 5.3 Contact Force 2 Limits for Roundness, Taper, or Straightness for Master Rings and Ring Gages <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 5.4 Tilt Tables 1 Location of Calibrated Diameter 3 Diameter Tolerances for Classes and Sizes for Master Rings and Ring Gages <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 5.5 Measurements Using a Mechanical Comparator 5.5.1 Dual Sphere Contact Probe Configuration 5.5.1.1 Mastering to a Ring Gage 4 Face Squareness Error\/Cosine Error Relationship <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 5.5.1.2 Mastering to a Gage Block Assembly 5.5.2 Single Sphere Contact Probe Configuration 5.5.2.1 Mastering to a Ring Gage <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 5.5.2.2 Mastering to Gage Blocks 5.5.3 Non-Contact Measurement Issues. 6 ENVIRONMENT 6.1 General 2 Typical Gage Block Combination Techniques for Ring Gage Measurements <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 6.2 Cleanliness 6.3 Vibration 6.4 Temperature 6.5 Humidity 6.6 Illumination <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | A EFFECTS OF FORM AND FORM ERRORS ON SIZE GEOMETRY A1 INTRODUCTION <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | B MEASUREMENT UNCERTAINTY B1 INTRODUCTION B2 GENERAL B3 EXAMPLE B4 RELEVANT INPUTS FOR APPENDIX EXAMPLE B5 MASTER GAGE CALIBRATION <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | B6 LONG TERM REPRODUCIBILITY OF MECHANICAL COMPARISON B7 THERMAL UNCERTAINTIES <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | B8 ELASTIC DEFORMATION B9 SCALE CALIBRATION <\/td>\n<\/tr>\n | ||||||
| 32<\/td>\n | B10 INSTRUMENT GEOMETRY B11 ARTIFACT GEOMETRY <\/td>\n<\/tr>\n | ||||||
| 33<\/td>\n | C ISO CYLINDRICAL RING BLANK DESIGN C1 RING GAUGES C1.1 Plain Ring Gauges <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" ASME B89.1.6 Measurement of Plain Internal Diameters for use as a Master Rings or Ring Guages<\/b><\/p>\n |