{"id":82351,"date":"2024-10-18T03:04:19","date_gmt":"2024-10-18T03:04:19","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/ieee-390-1987\/"},"modified":"2024-10-24T19:49:53","modified_gmt":"2024-10-24T19:49:53","slug":"ieee-390-1987","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/ieee\/ieee-390-1987\/","title":{"rendered":"IEEE 390 1987"},"content":{"rendered":"
Revision Standard – Active. Reaffirmed September 2007. Pulse transformers for use in electronic equipment are considered. This standard applies to the following transformer types: power output (drivers), impedance matching, interstage coupling, current sensing, and blocking-oscillator transformers. For these transformers, the peak power transmitted ranges from a few milliwatts to many kilowatts, and the peak voltage transmitted ranges from a few volts to many kilovolts. Symbols, performance tests, equivalent circuits, preferred test methods, marking, and service conditions are covered.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
1<\/td>\n | Title Page <\/td>\n<\/tr>\n | ||||||
3<\/td>\n | Introduction Participants <\/td>\n<\/tr>\n | ||||||
5<\/td>\n | CONTENTS <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | 1. Scope and References 1.1 Scope 1.2 References <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | 1.3 Typical Transformer Types to which this Standard Applies 1.4 Related Transformer Standards 2. Definitions <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 3. Symbols 3.1 Pulse Transformer Schematics 3.2 Input Pulse\u2014Source Voltage Pulse Applied Through Associated Impedance or Source Current Pulse <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 3.3 Output Pulse\u2014Transformed Voltage Pulse or Load Current Pulse 3.4 Source and Load Impedance 3.5 Transformer Parameters <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 4. Performance Tests 4.1 Electric Strength <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 4.2 Induced Voltage Electric Strength 4.3 Direct-Current Insulation Resistance <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 4.4 Ratio of Transformatoin (Turns Ratio) 4.5 Polarity 4.6 Direct-Current Resistance of Windings Referred to 25 \u00b0C 4.7 Short-Circuit Impedance (Leakage Inductance) <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 4.8 Open-Circuit Parameters (Magnetizing Pulse Inductance and Exciting Current) 4.9 Open-Circuit Admittance (Distributed Capacitance) <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 4.10 Voltage-Time Product Rating 4.11 Direct Capacitance Between Windings 4.12 Balance 4.13 Functional Test <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 4.14 Corona (Partial Discharge) Tests 4.15 Temperature Rise Test 5. Equivalent Circuits 5.1 Complete Equivalent Circuit for a Pulse Transformer <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | 5.2 Partial Equivalent Circuits for a Pulse Transformer <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | 5.3 Pulse Transformer Tests to Determine Equivalent Circuit Elements <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | 5.4 Pulse Response Parameters Under Load 6. Preferred Test Methods 6.1 Ratio of Transformation (Turns Ratio) Test Method <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | 6.2 Short-Circuit Impedance (Leakage Inductance) Test Method <\/td>\n<\/tr>\n | ||||||
29<\/td>\n | 6.3 Open-Circuit Admittance (Distributed Capacitance) Test Methods 6.4 Open-Circuit (Magnetizing Pulse Inductance and Exciting Current) Test Method. Recommended Method: Rectangular Voltage … <\/td>\n<\/tr>\n | ||||||
32<\/td>\n | 6.5 Voltage-Time Product Test Method. Recommended Methods: Rectangular Voltage Pulse Applied from Low-Impedance Source and .. <\/td>\n<\/tr>\n | ||||||
33<\/td>\n | 6.6 Three Recommended Balance Test Methods <\/td>\n<\/tr>\n | ||||||
34<\/td>\n | 6.7 Temperature Rise Test <\/td>\n<\/tr>\n | ||||||
36<\/td>\n | 6.8 Corona (Partial Discharge) Test 7. Marking <\/td>\n<\/tr>\n | ||||||
37<\/td>\n | 8. Service Conditions 9. Bibliography <\/td>\n<\/tr>\n | ||||||
38<\/td>\n | Annex A\u2014Alternate Test Methods <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" IEEE Standard for Pulse Transformers<\/b><\/p>\n |