{"id":96146,"date":"2024-10-18T10:25:43","date_gmt":"2024-10-18T10:25:43","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-d5133-6\/"},"modified":"2024-10-24T21:00:06","modified_gmt":"2024-10-24T21:00:06","slug":"astm-d5133-6","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-d5133-6\/","title":{"rendered":"ASTM-D5133"},"content":{"rendered":"
\n Significance and Use <\/b><\/p>\n
\n

5.1  Significance of Low-Temperature, Low Shear Rate, Engine Oil Rheology\u2014 <\/i> The low-temperature, low-shear viscometric behavior of an engine oil determines whether the oil will flow to the sump inlet screen, then to the oil pump, then to the sites in the engine requiring lubrication in sufficient quantity to prevent engine damage immediately or ultimately after cold temperature starting.<\/p>\n

\n

5.1.1 Two forms of flow problems have been identified, 4<\/span> <\/sup> <\/span> flow-limited and air-binding behavior. The first form of flow restriction, flow-limited behavior, is associated with the oil’s viscosity; the second, air-binding behavior, is associated with gelation.<\/p>\n<\/p><\/div>\n<\/p><\/div>\n

\n

5.2  Significance of the Test Method\u2014 <\/i> The temperature-scanning technique employed by this test method was designed to determine the susceptibility of the engine oil to flow-limited and air-binding response to slow cooling conditions by providing continuous information on the rheological condition of the oil over the temperature range of use. 4<\/span> <\/sup> <\/span> , <\/sup> 5<\/span> <\/sup> <\/span> , <\/sup> 7<\/span> <\/sup> <\/span> In this way, both viscometric and gelation response are obtained in one test.<\/p>\n

Note 1 <\/span> \u2014 This test method is one of three related to pumpability related problems. Measurement of low-temperature viscosity by the two other pumpability Test Methods D3829<\/span> and D4684<\/span> , hold the sample in a quiescent state and generate the apparent viscosity of the sample at shear rates ranging up to 15 sec -1 <\/sup> and shear stresses up to 525 Pa at a previously selected temperature. Such difference in test parameters (shear rate, shear stress, sample motion, temperature scanning, and so forth) can lead to differences in the measured apparent viscosity among these test methods with some test oils, particularly when other rheological factors associated with gelation are present. In addition, the three methods differ considerably in cooling rates. <\/span>\n <\/div>\n<\/p><\/div>\n
\n

5.3  Gelation Index and Gelation Index Temperature\u2014 <\/i> This test method has been further developed to yield parameters called the Gelation Index and Gelation Index temperature. The first parameter is a measure of the maximum rate of torque increase caused by the rheological response of the oil as the oil is cooled slowly. The second parameter is the temperature at which the Gelation Index occurs.<\/p>\n<\/p><\/div>\n

1. Scope <\/b><\/p>\n

\n

1.1 This test method covers the measurement of the apparent viscosity of engine oil at low temperatures.<\/p>\n<\/p><\/div>\n

\n

1.2 A shear rate of approximately 0.2 s -1 <\/sup> is produced at shear stresses below 100 Pa. Apparent viscosity is measured continuously as the sample is cooled at a rate of 1\u00b0C\/h over the range \u22125 to \u221240\u00b0C, or to the temperature at which the viscosity exceeds 40 000 mPa\u00b7s (cP).<\/p>\n<\/p><\/div>\n

\n

1.3 The measurements resulting from this test method are viscosity, the maximum rate of viscosity increase (Gelation Index), and the temperature at which the Gelation Index occurs.<\/p>\n<\/p><\/div>\n

\n

1.4 Applicability to petroleum products other than engine oils has not been determined in preparing this test method.<\/p>\n<\/p><\/div>\n

\n

1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.<\/p>\n<\/p><\/div>\n

\n

1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. <\/i><\/p>\n<\/p><\/div>\n

2. Referenced Documents <\/b> (purchase separately) <\/i> The documents listed below are referenced within the subject standard but are not provided as part of the standard.<\/span><\/p>\n

ASTM Standards <\/b><\/p>\n

<\/p>\n

D341<\/span> Practice for Viscosity-Temperature Charts for Liquid Petroleum Products<\/p>\n

<\/p>\n

D3829<\/span> Test Method for Predicting the Borderline Pumping Temperature of Engine Oil<\/p>\n

<\/p>\n

D4684<\/span> Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature<\/p>\n

Keywords <\/b><\/p>\n

borderline pumping temperature; critical pumpability temperature; critical pumpability viscosity; engine oil; gelation; Gelation Index; Gelation Index temperature; low-temperature engine oil pumpability; low-temperature rheology; Scanning Brookfield technique; temperature-scanning technique; viscosity;<\/p>\n

ICS Code <\/b><\/p>\n

ICS Number Code 75.100 (Lubricants, industrial oils and related products)<\/p>\n

DOI: <\/b> 10.1520\/D5133-12 ASTM International is a member of CrossRef. <\/p>\n

\n

ASTM D5133 (Petroleum Standards)<\/h2>\n<\/p><\/div>\n

Citing ASTM Standards<\/span><\/p>\n

[Back to Top]<\/span><\/p>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

D5133-12 Standard Test Method for Low Temperature, Low Shear Rate, Viscosity\/Temperature Dependence of Lubricating Oils Using a Temperature-Scanning Technique (Redline)<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
ASTM<\/b><\/a><\/td>\n2012<\/td>\n14<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":96147,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[2637],"product_tag":[],"class_list":{"0":"post-96146","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-astm","8":"first","9":"instock","10":"sold-individually","11":"shipping-taxable","12":"purchasable","13":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/96146","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/96147"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=96146"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=96146"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=96146"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}