ASME A112.18.2 2015
$98.04
ASME A112.18.2/CSA B125.2 – 2015: Plumbing Waste Fittings
| Published By | Publication Date | Number of Pages |
| ASME | 2015 | 50 |
This Standard covers plumbing waste fittings of sizes NPS-2 and smaller. This Standard does not cover (a) plumbing supply fittings, which are covered by ASME A112.18.1/CSA B125.1; (b) other devices (e.g., temperature-actuated in-line mixing valves), which are covered by CSA B125.3 or other plumbing product standards; and (c) flexible water connectors under continuous pressure, which are covered by ASME A112.18.6/CSA B125.6. This Standard does not cover pipes and tubes or pipe and tube fittings that are downstream of the trap. A112.18.2 is to be used in conjunction with components described in other volumes of the ASME A112 series. Careful application of these A112 standards will help users to comply with pertinent regulations—including those derived from the Uniform Plumbing Code (UPC) and the International Plumbing Code (IPC)—while achieving the operational and safety benefits to be gained from the many industry best-practices detailed within these volumes. Intended for manufacturers of plumbing materials and equipment to enhance water conservation and comply with jurisdictional regulation, plus governmental and other regulatory bodies.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 7 | Contents |
| 10 | Committee Roster |
| 18 | Preface |
| 21 | 1 Scope 2 Reference publications |
| 23 | 3 Definitions and abbreviations 3.1 Definitions |
| 24 | 3.2 Abbreviations |
| 25 | 4 General requirements 4.1 Materials |
| 26 | 4.2 Installation 4.3 Threads 4.4 Solder connections 4.5 Replacement parts |
| 27 | 4.6 Dimensions |
| 29 | 4.7 Mechanical stoppers 4.8 Additional requirements for linear shower drains 5 Performance requirements and test procedures 5.1 General |
| 30 | 5.2 Corrosion |
| 31 | 5.3 Thermal cycling 5.4 Coatings |
| 32 | 5.5 Shower drain strainers 5.6 Sink strainer assemblies |
| 33 | 5.7 Body and clamping rings of subdrains for built-up shower pans 5.8 Minimum flow rate |
| 34 | 5.9 Strength |
| 35 | 5.10 Life cycle 5.11 Seals leakage |
| 36 | 5.12 Leakage test for the seam between the bonding flange and membrane 6 Markings, packaging, and installation instructions 6.1 General 6.2 Packaging 6.3 Instructions for elastomeric waste fittings 6.4 Grey water diverters |
| 37 | Figures Figure 1 Sink and lavatory waste, trap, centre outlet, and patent overflow fittings Figure 2 Trap wall adapter |
| 38 | Figure 3 Sink strainer Figure 4 Sink strainer tailpiece |
| 39 | Figure 5 Tee Figure 6 Twin waste elbow |
| 40 | Figure 7 Centre outlet — Continuous waste assembly Figure 8 End outlet — Continuous waste assembly |
| 41 | Figure 9 Typical subdrain for built-up shower pans |
| 43 | Figure 10 Grey water diverter — Test of water flow through the sanitary drainage system outlet |
| 44 | Figure 11 Grey water diverter — Test of water flow through the diversion outlet |
| 45 | Figure 12 Grey water diverter — Test of water with the diversion mechanism in the diverted position and the diversion outlet blocked |
| 46 | Figure 13 Typical lavatory pop-up drain |
| 47 | Figure 14 Waste and overflow |
| 48 | Annex A |
Related products
-
ASME A112.18.2 2020
ASME A112.18.2/CSA B125.2 – 2020: Plumbing Waste Fittings Published By Publication Date Number of Pages…
-
ASME A112.18.2-2020/CSA B125.2:20
Plumbing waste fittings Published By Publication Date Number of Pages CSA 2020 61
