🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASTM-A479 2012(Redline)

ASTM-A479 2012(Redline)

$26.65

A479/A479M-12 Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels (Redline)

Published By Publication Date Number of Pages
ASTM 2012 9
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Abstract

This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction. Four grades of the stainless steel are available which includes austenitic, austenitic-ferritic, ferritic, and martensitic grades. Mechanical properties such as tensile strength, yield strength, elongation, and hardness shall be determined for the specimens subjected to normalized, tempered, annealed, and quenched conditions. The austenitic stainless steels shall be subjected to heat treatment and shall undergo corrosion test.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification 2 covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction. 2

Note 1 ??? There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards , Vol 02.04.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 Unless the order specifies the applicable ???M??? specification designation, the material shall be furnished to the inch-pound units.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels A370 Test Methods and Definitions for Mechanical Testing of Steel Products A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products E112 Test Methods for Determining Average Grain Size E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

 SAE Document

SAEJ1086 Recommended Practice for Numbering Metals and Alloys

Keywords

austenitic stainless steel; austenitic-ferritic duplex stainless steel; ferritic stainless steel; martensitic stainless steel; pressure-containing parts; pressure vessel service; stainless steel bars; stainless steel shapes; temperature service applications—high;

ICS Code

ICS Number Code 77.140.30 (Steels for pressure purposes)

DOI: 10.1520/A0479_A0479M-12 ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]

Related products

ASTM-A479 2012
$26.65