ASTM-D6073 1996
$35.75
D6073-96 Standard Test Method for Relative Setting of Heatset Printing Inks by the Sinvatrol Tester
| Published By | Publication Date | Number of Pages |
| ASTM | 1996 | 3 |
ASTM D6073-96
Historical Standard: Standard Test Method for Relative Setting of Heatset Printing Inks by the Sinvatrol Tester
ASTM D6073
Scope
1.1 This test method describes the procedure for determining the relative setting speed of heatset inks using a specific tester.
1.2 this test method is applicable to printing inks intended to be dried by the application of heat and for which a suitable reference standard is available.
1.3 Although heatset inks are normally printed by the offset process, this test method specifies the direct letterpress mode because the higher ink film thicknesses obtained tend to amplify subtle differences in ink setting speed.
1.4 This tester reads temperature and belt speed in nonmetric terms; therefore, instrument settings in this test method are stated first in U.S. Customary Units (inch-pound units of measurements). The values given in parentheses are for information only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Keywords
heat-set printing inks; printing apparatus; setting speed; tester
ICS Code
ICS Number Code n/a
DOI: 10.1520/D6073-96
Related products
-
ASTM-D673 1993
D673-93ae1 Test Method for Mar Resistance of Plastics (Withdrawn 1998) Published By Publication Date Number…
-
ASTM-D2073 1998
D2073-92(1998)e1 Standard Test Methods for Total, Primary, Secondary, and Tertiary Amine Values of Fatty Amines,…
-
ASTM-D6373 1999
D6373-99 Standard Specification for Performance Graded Asphalt Binder Published By Publication Date Number of Pages…
-
ASTM-D6078 1999
D6078-99 Standard Test Method for Evaluating Lubricity of Diesel Fuels by the Scuffing Load Ball-on-Cylinder…
-
ASTM-D6083 1997
D6083-97a Standard Specification for Liquid Applied Acrylic Coating Used in Roofing Published By Publication Date…
-
ASTM-D6063 1996
D6063-96e1 Standard Guide for Sampling of Drums and Similar Containers by Field Personnel Published By…
-
ASTM-D6473 1999
D6473-99 Standard Test Method for Specific Gravity and Absorption of Rock For Erosion Control Published…
-
ASTM-D6071:1996 Edition
D6071-96 Standard Test Method for Low Level Sodium in High Purity Water by Graphite Furnace…
-
ASTM-D6173:1997 Edition
D6173-97 Standard Test Method for Determination of Various Anionic Surfactant Actives by Potentiometric Titration Published…
-
ASTM-D6043 1996
D6043-96 Standard Guide for Selection of Permanent and Durable Artist’s Paper Published By Publication Date…
-
ASTM-D6079 1999
D6079-99 Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig…
-
ASTM-D6074 1999
D6074-99 Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils Published By Publication Date Number of…
-
ASTM-D603 1996
D603-66(1996)e1 Standard Specification for Aluminum Silicate Pigments (Hydrous) (Withdrawn 2004) Published By Publication Date Number…
-
ASTM-D6521:2008 Edition(Redline)
D6521-08 Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV)…
-
ASTM-D1073:1999 Edition
D1073-99 Standard Specification for Fine Aggregate for Bituminous Paving Mixtures Published By Publication Date Number…
-
ASTM-D6003 1996
D6003-96 Standard Test Method for Determining Weight Loss From Plastic Materials Exposed to Simulated Municipal…
-
ASTM-D3073 1991
D3073-72(1991)e1 Practice for Filling and Inspection of Glass Aerosol Containers (Withdrawn 1997) Published By Publication…
