ASTM-F2779 2010

$40.63

F2779-10 Standard Practice for Commercial Radial Truck-Bus Tires to Establish Equivalent Test Severity Between a 1.707-m (67.23-in.) Diameter Roadwheel and a Flat Surface

Published By	Publication Date	Number of Pages
ASTM	2010	8

Guaranteed Safe Checkout

Categories: 83.160.10 - Road vehicle tyres, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

1.1 This practice describes the procedure to identify equivalent test severity conditions between a 1.707-m diameter laboratory roadwheel surface and a flat or highway surface for commercial radial truck-bus tires.

1.1.1 Tire operational severity, as defined as the running or operational temperature for certain specified internal tire locations, is not the same for these two test conditions. It is typically higher for the laboratory roadwheel at equal load, speed and inflation pressure conditions due to the curvature effect.

1.1.2 The practice applies to specific operating conditions of load range F through L for such commercial radial truck-bus tires.

1.1.3 The specific operating conditions under which the procedures of the practice are valid and useful are completely outlined in Section 6 (Limitations) of this standard.

1.1.4 It is important to note that this standard is composed of two distinct formats:

1.1.4.1 The usual text format as published in this volume of the Book of Standards (Vol 09.02).

1.1.4.2 A special interactive electronic format that uses a special software tool, designated as prediction profilers or profilers. This special profiler may be used to determine laboratory test conditions that provide equivalent tire internal temperatures for the tread centerline, belt edge, or ply ending region for the two operational conditions, that is, the curved laboratory roadwheel and flat highway test surfaces.

1.2 The prediction profilers are based on empirically developed linear regression models obtained from the analysis of a large database that was obtained from a comprehensive experimental test program for roadwheel and flat surface testing of typical commercial truck and bus tires. See Section 7 and References (1, 2) ^, for more details.

1.2.1 For users viewing the standard on CD-ROM or PDF, with an active and working internet connection, the profilers can be accessed on the ASTM website by clicking on the links in 7.5 and 7.6.

1.2.2 For users viewing the standard in a printed format, the profilers can be accessed by entering the links to the ASTM website in 7.5 and 7.6 into their internet browsers.

1.3 For this standard, SI units shall be used, except where indicated.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology
2	Summary of Practice Significance and Use
3	Limitations Procedure Keywords
4	A1. PREDICTION PROFILER EXAMPLES A1.1 A1.2 A1.3
5	FIG. A1.1 FIG. A1.2
6	X1. BASIS OF THE PROFILING TO PREDICT EQUIVALENT TEST CONDITIONS X1.1 Measured Tire Temperature Locations X2. RATIONALE X2.1 X2.2 X2.3 X2.4 Commercial Radial Truck-Bus Tire Endurance Perfor-mance FIG. X1.1
7	X2.5 X2.6 REFERENCES

Additional information

Standard Title	F2779-10 Standard Practice for Commercial Radial Truck-Bus Tires to Establish Equivalent Test Severity Between a 1.707-m (67.23-in.) Diameter Roadwheel and a Flat Surface
Published Code	ASTM
Publication Date	2010
Pages Count	8
ICS Codes	83.160.10 - Road vehicle tyres

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-F2779 2010

PDF Catalog

Related products