BS EN 60384-15:2017
$167.15
Fixed capacitors for use in electronic equipment – Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte
| Published By | Publication Date | Number of Pages |
| BSI | 2017 | 40 |
IEC 60384-15:2017(E) applies to through-hole/leaded polar and bipolar tantalum electrolyte capacitors with solid and non?solid electrolyte for use in electronic equipment. It includes capacitors for long?life applications and capacitors for general?purpose applications. This document prescribes preferred ratings and characteristics and to select from IEC 60384?1:2016 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. This edition includes the following significant technical changes with respect to the previous edition: a) Revision of the structure in accordance with ISO/IEC Directives, Part 2:2016 (seventh edition) to the extent practicable, and harmonization between other similar kinds of documents. b) In addition, Clause 4 and all the tables have been reviewed in order to prevent duplications and contradictions.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | National foreword |
| 11 | 1.1 Scope 1.2 Object 1.3 Normative references |
| 12 | 1.4 Information to be given in a detail specification 1.4.1 General 1.4.2 Outline drawing and dimensions 1.4.3 Mounting 1.4.4 Ratings and characteristics |
| 13 | 1.4.5 Marking 1.5 Terms and definitions 1.6 Marking 1.6.1 General |
| 14 | 1.6.2 Information for marking 1.6.3 Marking on capacitors 1.6.4 Marking on packaging 2.1 Preferred characteristics 2.2 Preferred values of ratings 2.2.1 Nominal capacitance (CN) |
| 15 | 2.2.2 Tolerance on nominal capacitance 2.2.3 Rated voltage (UR) 2.2.4 Category voltage (UC) 2.2.5 Reverse voltage 2.2.6 Surge voltage (URS or UCS) 2.2.7 Ripple (if required) Table 1 – Rated, category and surge voltages |
| 16 | 2.2.8 Rated temperature 3.1 Primary stage of manufacture 3.2 Structurally similar components 3.3 Certified test records of released lots 3.4 Qualification approval procedures 3.4.1 General 3.4.2 Qualification approval on the basis of the fixed sample size procedure |
| 17 | 3.4.3 Tests |
| 18 | Table 2 – Sampling plan for qualification approval tests |
| 19 | Table 3 – Test schedule for qualification approval (1 of 6) |
| 24 | 3.5 Quality conformance inspection 3.5.1 Formation of inspection lots |
| 25 | 3.5.2 Test schedule 3.5.3 Delayed delivery 3.5.4 Assessment levels Table 4 – Lot-by-Lot inspection |
| 26 | 4.1 Visual inspection and check of dimensions 4.2 Electrical tests 4.2.1 Leakage current 4.2.2 Capacitance Table 5 – Periodic Inspection |
| 27 | 4.2.3 Tangent of loss angle (tan δ) 4.2.4 Impedance (if required) |
| 28 | 4.2.5 Insulation resistance of the external insulation (if required) 4.2.6 Voltage proof of the external insulation (if required) |
| 29 | 4.3 Robustness of terminations 4.3.1 General 4.3.2 Initial inspection 4.3.3 Test Ua1, Ub and Uc applicable 4.3.4 Special bending test |
| 30 | 4.4 Resistance to soldering heat 4.4.1 General 4.4.2 Conditions 4.4.3 Final inspections and requirements 4.5 Solderability 4.5.1 General 4.5.2 Test conditions 4.5.3 Final inspections and requirements 4.6 Rapid change of temperature 4.6.1 General |
| 31 | 4.6.2 Initial inspection 4.6.3 Test conditions 4.6.4 Recovery 4.6.5 Final inspections and requirements 4.7 Vibration 4.7.1 General 4.7.2 Test condition 4.7.3 Final inspections and requirements 4.8 Bump 4.8.1 General Table 6 – Vibration test frequencies |
| 32 | 4.8.2 Mounting 4.8.3 Test conditions 4.8.4 Final inspections and requirements 4.9 Shock 4.9.1 General 4.9.2 Mounting 4.9.3 Test conditions Table 7 – Shock peak acceleration/pulse duration |
| 33 | 4.9.4 Final inspections and requirements 4.10 Climatic sequence 4.10.1 General 4.10.2 Initial inspection 4.10.3 Dry heat 4.10.4 Damp heat, cyclic, Test Db, first cycle 4.10.5 Cold 4.10.6 Low air pressure (if required) 4.10.7 Damp heat, cyclic, Test Db, remaining cycles 4.10.8 Recovery |
| 34 | 4.10.9 Sealing (if required) 4.10.10 Final inspections and requirements 4.11 Damp heat, steady state 4.11.1 General 4.11.2 Initial inspection 4.11.3 Final inspections and requirements 4.12 Endurance 4.12.1 General 4.12.2 Initial inspection 4.12.3 Test conditions |
| 35 | 4.12.4 Recovery 4.12.5 Final inspections and requirements 4.13 Surge voltage 4.13.1 General 4.13.2 Initial inspection 4.13.3 Test conditions 4.13.4 Final inspections and requirements Table 8 – Test temperature |
| 36 | 4.14 Reverse voltage (if required) 4.14.1 General 4.14.2 Initial inspection 4.14.3 Test conditions 4.14.4 Final inspections and requirements 4.15 Characteristics at high and low temperature 4.15.1 General 4.15.2 Final inspections and requirements 4.16 Charge and discharge (if required) 4.16.1 General 4.16.2 Initial inspection |
| 37 | 4.16.3 Test conditions 4.16.4 Recovery 4.16.5 Final inspections and requirements 4.17 Component solvent resistance 4.18 Solvent resistance of the marking 4.19 High surge current (if required) 4.19.1 General 4.19.2 Initial inspection 4.19.3 Final inspections and requirements |
