BS EN ISO 10855-1:2018
$167.15
Offshore containers and associated lifting sets – Design, manufacture and marking of offshore containers
| Published By | Publication Date | Number of Pages |
| BSI | 2018 | 40 |
This document specifies requirements for the design, manufacture and marking of offshore containers with a maximum gross mass not exceeding 25 000 kg, intended for repeated use to, from and between offshore installations and ships.
This document specifies only transport-related requirements.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | National foreword |
| 4 | European foreword |
| 7 | Foreword |
| 8 | Introduction |
| 9 | 1 Scope 2 Normative references |
| 11 | 3 Terms and definitions |
| 13 | 4 Symbols 5 Design 5.1 General |
| 14 | 5.2 Structural strength 5.2.1 General |
| 15 | 5.2.2 Lifting loads |
| 16 | 5.2.3 Impact loads |
| 17 | 5.2.4 Internal forces on container walls 5.2.5 Minimum material thickness 5.3 Welding 5.4 Additional design details 5.4.1 Floor |
| 18 | 5.4.2 Doors and hatches 5.4.3 Intermediate cargo decks 5.4.4 Driving ramps 5.4.5 Internal lashing points 5.4.6 Fork lift pockets |
| 19 | 5.4.7 Top protection 5.4.8 Pad eyes |
| 20 | 5.4.9 ISO-corner fittings 5.4.10 Equipment 5.4.11 Coating and corrosion protection |
| 21 | 5.5 Tank containers 5.5.1 General 5.5.2 Frame 5.5.3 Tanks for fluids 5.5.4 Impact protection on tank containers for dangerous cargoes 5.6 Containers for bulk solids |
| 22 | 6 Materials 6.1 Steel — General |
| 23 | 6.2 Rolled and extruded steels in offshore container structures 6.2.1 General requirements 6.2.2 Groups of steels 6.2.3 Stainless steel 6.2.4 Steel forgings |
| 24 | 6.2.5 Steel castings in ISO-corner fittings 6.3 Aluminium |
| 25 | 6.4 Non-metallic materials |
| 26 | 6.5 Material documents 7 Type testing 7.1 General |
| 27 | 7.2 Test equipment and calibration 7.2.1 Test mass/test load 7.2.2 Calibration 7.3 Lifting test 7.3.1 General 7.3.2 All-point lifting |
| 28 | 7.3.3 Two-point lifting 7.3.4 Post-lifting test inspection and examination 7.4 Vertical impact test 7.5 Other tests |
| 29 | 8 Production 8.1 General 8.2 Primary structure 8.2.1 General 8.2.2 Approved welders 8.2.3 Examination of welds |
| 31 | 8.3 Secondary structure 8.4 Production testing 8.4.1 Lifting test 8.4.2 Weather proofness testing |
| 32 | 8.5 Failure of production containers 9 Marking 9.1 Safety marking 9.2 Identification markings 9.3 Information markings |
| 33 | 9.4 Other markings 10 Container data plate 10.1 General 10.2 Contents of data plate |
| 34 | 11 Certificate of conformity 11.1 General 11.2 Documentation |
| 35 | 11.3 Contents of the certificate of conformity |
| 36 | Annex A (informative) Regulations for offshore containers |
| 38 | Bibliography |
