{"id":43222,"date":"2024-10-17T06:37:17","date_gmt":"2024-10-17T06:37:17","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-a684-2010-2\/"},"modified":"2024-10-24T15:45:53","modified_gmt":"2024-10-24T15:45:53","slug":"astm-a684-2010-2","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-a684-2010-2\/","title":{"rendered":"ASTM-A684 2010"},"content":{"rendered":"

ASTM A684\/A684M-10a<\/h3>\n

Historical Standard: Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled<\/h4>\n
\n

ASTM A684\/A684M<\/h4>\n

Scope<\/strong><\/p>\n

1.1 This specification covers cold-rolled, high-carbon strip in coils or cut lengths. Strip is classified as product that is 0.3000 in. [7.6 mm] or less in thickness and over \u00bd<\/span> to 2315<\/sup>\/16<\/sub><\/small> in. [12.5 to 600 mm] in width, inclusive. Strip tolerance products may be available in widths wider than 2315<\/sup>\/16<\/sub><\/small> in. (600 mm) by agreement between purchaser and supplier; however, such products are technically classified as cold-rolled sheet. The maximum of the specified carbon range is over 0.25 to 1.35 %, inclusive. It is furnished in the following types as specified:<\/p>\n

1.1.1 Soft spheroidized annealed high-carbon steel is intended for applications requiring maximum cold forming. It is normally produced to give the lowest maximum Rockwell hardness for each grade.<\/p>\n

1.1.2 Soft annealed high-carbon steel is intended for applications requiring moderate cold forming. It is produced to a maximum Rockwell hardness.<\/p>\n

1.1.3 Intermediate hardness high-carbon steel is intended for applications where cold forming is slight or a stiff, springy product is needed, or both. It is produced to specified Rockwell hardness ranges, the maximum being higher than obtained for the annealed type.<\/p>\n

1.1.4 Full hard high-carbon steel is intended for flat applications. It is produced to minimum Rockwell hardness requirements, which vary with grade, microstructure and gauge. Full hard can be produced with either a pearlitic or spheroidized microstructure or a mixture of both. The minimum hardness should be established between the consumer and the producer.<\/p>\n

1.2 This specification is applicable for orders in either inch-pound units or SI units.<\/p>\n

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.<\/p>\n

Keywords<\/strong><\/p>\n

cold rolled strip; high carbon; steel; strip; Carbon steel sheet\/strip–specifications; Cold-rolled steel sheet\/strip–specifications; Intermediate hardness carbon spring steel; Spheroidized carbon spring steel; Steel springs–specifications<\/p>\n

ICS Code<\/strong><\/p>\n

ICS Number Code 77.140.50 (Flat steel products and semi-products)<\/p>\n

DOI:<\/strong> 10.1520\/A0684_A0684M-10A<\/p>\n<\/div>\n

PDF Catalog<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n
PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
1<\/td>\nScope
Referenced Documents <\/td>\n<\/tr>\n
2<\/td>\nTerminology
Ordering Information
Manufacture
TABLE 1 <\/td>\n<\/tr>\n
3<\/td>\nChemical Requirements
Metallurgical Structure
TABLE 2
TABLE 3
TABLE 4 <\/td>\n<\/tr>\n
4<\/td>\nMechanical Requirements
Dimensions, Mass, and Permissible Variations
Finish and Edges
TABLE 5
TABLE 6 <\/td>\n<\/tr>\n
5<\/td>\nFIG. 1
FIG. 2 <\/td>\n<\/tr>\n
6<\/td>\nWorkmanship
Number of Tests and Retests
Rework and Retreatment
TABLE 7
TABLE 8 <\/td>\n<\/tr>\n
7<\/td>\nInspection
Rejection and Rehearing
Certification and Reports
Marking
Packaging
Keywords
TABLE 9 <\/td>\n<\/tr>\n
8<\/td>\nTABLE 10 <\/td>\n<\/tr>\n
9<\/td>\nTABLE 11
TABLE 12 <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

A684\/A684M-10a Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
ASTM<\/b><\/a><\/td>\n2010<\/td>\n10<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":43223,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[1118,2637],"product_tag":[],"class_list":{"0":"post-43222","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-77-140-50","7":"product_cat-astm","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/43222","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/43223"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=43222"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=43222"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=43222"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}