ASTM-C1583/C1583M:2020 Edition
$34.13
C1583/C1583M-20 Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)
| Published By | Publication Date | Number of Pages |
| ASTM | 2020 | 5 |
ASTM C1583/C1583M-20
Active Standard: Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)
ASTM C1583/C1583M
Scope
1.1 This test method is suitable for both field and laboratory use to determine one or more of the following:
1.1.1 The near-surface tensile strength of the substrate as an indicator of the adequacy of surface preparation before application of a repair or overlay material.
1.1.2 The bond strength of a repair or an overlay material to the substrate.
1.1.3 The tensile strength of a repair or overlay material, or an adhesive used in repairs, after the material has been applied to a surface.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Keywords
adhesives; overlay materials; pull-off tensile strength; pull-off test; repair materials; tensile bond strength;
ICS Code
ICS Number Code 91.080.40 (Concrete structures)
DOI: 10.1520/C1583_C1583M-20
ASTM-C1583/C1583M:2020 Edition(Redline)
$40.63
C1583/C1583M-20 Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method) (Redline)
| Published By | Publication Date | Number of Pages |
| ASTM | 2020 | 5 |
ASTM C1583/C1583M-20
Redline Standard: Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)
ASTM C1583/C1583M
Scope
1.1 This test method is suitable for both field and laboratory use to determine one or more of the following:
1.1.1 The near-surface tensile strength of the substrate as an indicator of the adequacy of surface preparation before application of a repair or overlay material.
1.1.2 The bond strength of a repair or an overlay material to the substrate.
1.1.3 The tensile strength of a repair or overlay material, or an adhesive used in repairs, after the material has been applied to a surface.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Keywords
adhesives; overlay materials; pull-off tensile strength; pull-off test; repair materials; tensile bond strength;
ICS Code
ICS Number Code 91.080.40 (Concrete structures)
DOI: 10.1520/C1583_C1583M-20
Related products
-
ASTM-C1583/C1583M:2020 Edition(Redline)
C1583/C1583M-20 Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or…
