šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
ASTM-D1653:2008 Edition(Redline)

ASTM-D1653:2008 Edition(Redline)

$26.65

D1653-03(2008) Standard Test Methods for Water Vapor Transmission of Organic Coating Films (Redline)

Published By Publication Date Number of Pages
ASTM 2008 6
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

Significance and Use

One of the factors affecting the performance provided by an organic coating is its capability of resisting or aiding the passage of water vapor. In some services, for example, exterior wood and masonry, the coating has to allow moderate amounts of water vapor to pass through the film without damage to it. Hence, the water vapor transmission characteristics of coatings are important in assessing their performance in practical use.

The purpose of these test methods is to obtain values of water vapor transfer through coatings that range in permeability from high to low. These values are for use in design, manufacture, and marketing.

The water vapor transmission is not a linear function of film thickness, temperature or relative humidity.

Values of water vapor transmission rate (WVT) and water vapor permeance (WVP) can be used in the relative rating of coatings only if the coatings are tested under the same closely controlled conditions of temperature and relative humidity, and if their thicknesses are equal.

Test Method A ā€” The Dry Cup Method is the preferred test method for obtaining values that relate to conventional dwellings where high relative humidities are not anticipated.

Test Method B ā€” The Wet Cup Method is the preferred test method for obtaining values that relate to applications where high relative humidities are anticipated in the vicinity of the barrier material. In general, the more permeable a coating is to the passage of moisture as is typical of many water-reducible coatings, the greater its affinity for water and the greater the increase in transmission when tested in and exposed to high humidities. Absorption of water may make a coating less dense, thus allowing moisture to diffuse easily and cause a much higher moisture vapor transmission rate, (WVTR) than would occur in drier environments.

1. Scope

1.1 These test methods cover the determination of the rate at which water vapor passes through films of paint, varnish, lacquer, and other organic coatings. The films may be free films or they may be applied to porous substrates.

1.2 Two test methods are covered as follows:

1.2.1 Test Method A ā€” Dry Cup Method, and

1.2.2 Test Method B ā€” Wet Cup Method.

1.2.3 Agreement should not be expected between results obtained by different methods or test conditions. The method that most closely approaches the conditions of use should be selected.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Factors for conversion are stated in 13.2.1.2 and 13.2.2.2.

1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D823 Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers D1193 Specification for Reagent Water D4708 Practice for Preparation of Uniform Free Films of Organic Coatings E104 Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions

Keywords

permeance; perms; water vapor permeance; water vapor transmission; Permeability–coatings/films; Lacquer; Moisture vapor processing; Organic coatings; Paint testing; Permeance; Dry cup method; Specific permeability; Varnishes; Water vapor permeability; Water vapor transmission (WVT); Wet cup method;

ICS Code

ICS Number Code 25.220.60 (Organic coatings)

DOI: 10.1520/D1653-03R08 ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]

Related products

ASTM-D1653
$26.65