BS EN ISO 9806:2013
$215.11
Solar energy. Solar thermal collectors. Test methods
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 130 |
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | Foreword |
| 8 | Foreword |
| 9 | Introduction |
| 11 | Section sec_1 Section sec_2 Section sec_3 1 Scope 2 Normative references 3 Terms and definitions |
| 12 | Section sec_3.1 Section sec_3.2 Section sec_3.3 Section sec_3.4 Section sec_3.5 Section sec_3.6 Section sec_3.7 Section sec_3.8 Section sec_3.9 Section sec_3.10 Section sec_3.11 |
| 13 | Section sec_3.12 Section sec_3.13 Section sec_3.14 Section sec_3.15 Section sec_4 4 Symbols and abbreviated terms |
| 18 | Section sec_5 Section sec_5.1 5 General 5.1 Test overview – Sequence of the tests |
| 19 | Table tab_1 Section sec_5.2 5.2 Particular aspects of collectors using external power sources and active or passive measures for normal operation and self-protection |
| 20 | Section sec_6 Section sec_6.1 Section sec_6.1.1 Section sec_6.1.2 Section sec_6.1.3 Section sec_6.2 Section sec_6.2.1 Section sec_6.3 Section sec_6.3.1 6 Internal pressure tests for fluid channels 6.1 Inorganic fluid channels 6.2 Fluid channels made of organic materials (plastics or elastomers) 6.3 Apparatus and procedure |
| 21 | Section sec_6.3.2 Section sec_6.3.3 Section sec_6.3.4 Section sec_6.4 Section sec_7 Section sec_7.1 Section sec_7.2 6.4 Results 7 Leakage test (closed loop air heating collectors only) 7.1 Objective 7.2 Apparatus and procedure |
| 22 | Table tab_b Figure fig_1 Section sec_7.3 Section sec_7.4 Section sec_8 Section sec_8.1 7.3 Test conditions 7.4 Results 8 Rupture or collapse test (air heating collectors only) 8.1 Objective |
| 23 | Section sec_8.2 Section sec_8.2.1 Section sec_8.2.2 Section sec_8.2.3 8.2 Apparatus and Procedure |
| 24 | Section sec_8.3 Section sec_8.3.1 Section sec_8.4 Section sec_9 Section sec_9.1 Section sec_9.2 8.3 Test conditions 8.4 Results and reporting 9 High-temperature resistance test 9.1 Objective 9.2 Apparatus and procedure |
| 25 | Section sec_9.3 Table tab_2 Section sec_9.4 9.3 Test conditions 9.4 Results |
| 26 | Section sec_10 Section sec_10.1 Table tab_3 Section sec_10.2 10 Standard stagnation temperature of liquid heating collectors 10.1 General 10.2 Measurement and extrapolation of standard stagnation temperature |
| 27 | Section sec_10.3 Section sec_10.4 10.3 Determining standard stagnation temperature using efficiency parameters 10.4 Results |
| 28 | Section sec_11 Section sec_11.1 Section sec_11.2 Section sec_11.3 11 Exposure and pre-exposure test 11.1 Objective 11.2 Apparatus and procedure 11.3 Test conditions |
| 29 | Table tab_4 Section sec_11.3.1 Section sec_11.4 Section sec_12 Section sec_12.1 Section sec_12.2 11.4 Results 12 External thermal shock test 12.1 Objective 12.2 Apparatus and procedure |
| 30 | Section sec_12.3 Section sec_12.4 Section sec_13 Section sec_13.1 Section sec_13.2 12.3 Test conditions 12.4 Results 13 Internal thermal shock test 13.1 Objective 13.2 Apparatus and procedure |
| 31 | Section sec_13.3 Section sec_13.4 Section sec_14 Section sec_14.1 Section sec_14.2 13.3 Test conditions 13.4 Results 14 Rain penetration test 14.1 Objective 14.2 Apparatus and procedure |
| 32 | Section sec_14.3 14.3 Test conditions |
| 33 | Table tab_c Figure fig_2 Figure fig_3 |
| 34 | Figure fig_4 Section sec_14.4 Section sec_15 Section sec_15.1 Section sec_15.2 Section sec_15.2.1 Section sec_15.2.2 Section sec_15.2.3 14.4 Results 15 Freeze resistance test 15.1 Objective 15.2 Apparatus and procedure |
| 35 | Section sec_15.3 Section sec_15.4 Section sec_16 Section sec_16.1 Section sec_16.2 Section sec_16.2.1 15.3 Test conditions 15.4 Results 16 Mechanical load test with positive or negative pressure 16.1 Objectives 16.2 Apparatus and procedure |
| 36 | Section sec_16.2.2 Section sec_16.2.3 Section sec_16.3 Section sec_16.4 Section sec_17 Section sec_17.1 16.3 Test conditions 16.4 Results 17 Impact resistance test 17.1 Objective |
| 37 | Section sec_17.2 Section sec_17.3 Section sec_17.4 Section sec_17.4.1 17.2 Test procedure 17.3 Impact location 17.4 Method 1: Impact resistance test using ice balls |
| 38 | Section sec_17.4.2 Table tab_5 Section sec_17.4.3 Section sec_17.5 Section sec_17.6 17.5 Method 2: Impact resistance test using steel balls 17.6 Results |
| 39 | Section sec_18 Section sec_19 Section sec_20 Section sec_20.1 18 Final inspection (related to Clauses 5 to 17) 19 Test report (related to Clauses 5 to 18) 20 Performance testing of fluid heating collectors 20.1 General |
| 40 | Section sec_20.2 Section sec_20.2.1 Section sec_20.2.2 20.2 Steady-state efficiency test using a solar irradiance simulator |
| 41 | Section sec_20.2.3 Section sec_21 Section sec_21.1 Section sec_21.2 Section sec_21.2.1 Section sec_21.2.2 Section sec_21.2.2.1 Section sec_21.2.2.2 21 Collector mounting and location 21.1 General 21.2 Collector frame |
| 42 | Section sec_21.3 Section sec_21.4 Section sec_21.5 21.3 Tilt angle 21.4 Collector orientation outdoors 21.5 Shading from direct solar irradiance |
| 43 | Section sec_21.6 Section sec_21.7 Section sec_21.8 Section sec_21.8.1 Section sec_21.8.2 Section sec_21.8.3 21.6 Diffuse and reflected solar irradiance 21.7 Thermal irradiance 21.8 Surrounding air speed |
| 44 | Section sec_22 Section sec_22.1 Section sec_22.1.1 Section sec_22.1.1.1 Section sec_22.1.1.2 Section sec_22.1.1.3 Section sec_22.1.1.4 22 Instrumentation 22.1 Solar radiation measurement |
| 45 | Section sec_22.1.1.5 Section sec_22.1.1.6 Section sec_22.1.1.7 Section sec_22.2 Section sec_22.2.1 22.2 Thermal radiation measurement |
| 46 | Section sec_22.2.2 Section sec_22.2.3 Section sec_22.2.4 Section sec_22.2.4.1 |
| 47 | Section sec_22.2.4.2 Section sec_22.3 Section sec_22.3.1 Section sec_22.3.2 Section sec_22.3.2.1 Section sec_22.3.2.2 22.3 Temperature measurements |
| 48 | Section sec_22.3.2.3 Section sec_22.3.3 Section sec_22.3.3.1 Section sec_22.3.3.2 Section sec_22.3.3.3 |
| 49 | Section sec_22.3.3.4 Section sec_22.3.4 Section sec_22.3.4.1 Section sec_22.3.4.2 Section sec_22.4 Section sec_22.4.1 Section sec_22.4.2 Table tab_6 22.4 Flow rate measurement |
| 50 | Section sec_22.5 Section sec_22.5.1 Section sec_22.5.2 Section sec_22.5.2.1 Section sec_22.5.2.1.1 22.5 Surrounding air speed measurement |
| 51 | Section sec_22.5.2.1.2 Section sec_22.6 Section sec_22.7 22.6 Elapsed time measurement 22.7 Pressure measurement |
| 52 | Section sec_22.8 Section sec_22.9 Section sec_22.10 Section sec_23 Section sec_23.1 Section sec_23.1.1 22.8 Humidity measurement 22.9 Collector gross area 22.10 Collector fluid capacity 23 Test installation 23.1 Liquid heating collectors |
| 53 | Table tab_d Figure fig_5 |
| 54 | Table tab_e Figure fig_6 Section sec_23.1.2 |
| 55 | Section sec_23.1.3 Section sec_23.1.4 Section sec_23.1.5 |
| 56 | Section sec_23.2 Section sec_23.2.1 Section sec_23.2.2 Table tab_f Figure fig_7 23.2 Air heating collectors |
| 57 | Section sec_23.2.3 Table tab_g Figure fig_8 Section sec_23.2.4 Section sec_23.2.5 |
| 58 | Section sec_23.2.6 Section sec_23.2.7 Section sec_23.2.8 Section sec_24 Section sec_24.1 24 Performance test procedures 24.1 General |
| 59 | Section sec_24.2 Section sec_24.3 Section sec_24.4 Section sec_24.4.1 Section sec_24.4.2 Section sec_24.4.2.1 Section sec_24.4.2.2 24.2 Test installation 24.3 Preconditioning of the collector 24.4 Test conditions |
| 60 | Section sec_24.4.2.3 Section sec_24.4.2.4 |
| 61 | Section sec_24.4.3 Section sec_24.5 Section sec_24.5.1 Section sec_24.5.2 Section sec_24.5.3 Section sec_24.5.4 24.5 Test procedure |
| 62 | Table tab_7 Section sec_24.5.5 Section sec_24.6 Section sec_24.6.1 24.6 Measurements |
| 63 | Table tab_8 Section sec_24.6.2 Section sec_24.6.2.1 |
| 64 | Section sec_24.6.2.2 Section sec_24.6.2.3 Section sec_24.6.3 Section sec_24.7 Section sec_24.7.1 Section sec_24.7.1.1 24.7 Test period |
| 65 | Table tab_9 Section sec_24.7.2 Section sec_24.7.2.1 Section sec_24.7.2.2 |
| 66 | Section sec_24.7.2.3 Section sec_24.7.2.4 |
| 67 | Figure fig_9 Figure fig_10 |
| 68 | Figure fig_11 Figure fig_12 |
| 69 | Section sec_24.8 Section sec_24.8.1 Section sec_24.8.2 Section sec_24.8.3 Section sec_25 Section sec_25.1 Section sec_25.1.1 24.8 Presentation of results 25 Computation of the collector parameters 25.1 Liquid heating collectors |
| 70 | Section sec_25.1.2 Section sec_25.1.2.1 Section sec_25.1.2.2 |
| 71 | Section sec_25.1.3 Section sec_25.1.3.1 Section sec_25.1.3.2 Section sec_25.1.4 Section sec_25.1.4.1 |
| 72 | Section sec_25.1.4.2 Section sec_25.1.4.3 Section sec_25.1.4.4 |
| 73 | Section sec_25.2 Section sec_25.2.1 Section sec_25.2.2 25.2 Steady-state air heating collectors |
| 74 | Section sec_26 Section sec_26.1 Section sec_26.1.1 Section sec_26.1.2 Section sec_26.1.2.1 Section sec_26.1.2.2 Section sec_26.1.2.3 26 Determination of the effective thermal capacity and the time constant of a collector 26.1 Measurement of the effective thermal capacity (separate measurement) |
| 75 | Section sec_26.1.2.4 Section sec_26.1.3 |
| 76 | Section sec_26.2 Section sec_26.3 Section sec_26.3.1 26.2 Measurement of the effective thermal capacity (quasi dynamic method) 26.3 Calculation method |
| 77 | Section sec_26.3.2 Table tab_10 Section sec_26.3.3 Section sec_26.4 Section sec_26.4.1 26.4 Determination of collector time constant (optional) |
| 78 | Section sec_26.4.2 Table tab_h Figure fig_13 |
| 79 | Section sec_27 Section sec_27.1 Section sec_27.1.1 Section sec_27.1.2 27 Determination of incident angle modifier 27.1 Modelling |
| 80 | Table tab_i Figure fig_14 Section sec_27.1.3 |
| 81 | Table tab_j Figure fig_15 Section sec_27.1.4 |
| 82 | Table tab_k Figure fig_16 |
| 83 | Section sec_27.2 Section sec_27.2.1 Section sec_27.2.1.1 Section sec_27.2.1.2 Section sec_27.2.1.3 Section sec_27.2.2 Section sec_27.2.3 27.2 Test procedures |
| 84 | Section sec_27.3 Section sec_27.3.1 Section sec_27.3.2 Section sec_27.3.3 27.3 Calculation of collector incidence angle modifier |
| 85 | Section sec_28 Section sec_28.1 Section sec_28.2 Section sec_28.3 Section sec_28.4 28 Determination of the pressure drop across a collector (Liquid) (optional) 28.1 General 28.2 Test installation 28.3 Preconditioning of the collector 28.4 Test procedure |
| 86 | Section sec_28.5 Section sec_28.6 Section sec_28.7 28.5 Measurements 28.6 Pressure drop caused by fittings 28.7 Test conditions |
| 87 | Section sec_28.8 Section sec_28.9 Section sec_28.9.1 Table tab_l Figure fig_17 Section sec_28.9.2 28.8 Calculation and presentation of results 28.9 Pressure drop for air collectors |
| 88 | Section sec_28.9.3 Section sec_28.9.4 Table tab_m Figure fig_18 |
| 89 | Annex sec_A Annex sec_A.1 Annex A (normative) Test reports |
| 91 | Annex sec_A.2 |
| 92 | Table tab_A.1 Annex sec_A.3 Annex sec_A.3.1 Annex sec_A.3.2 Annex sec_A.3.3 Annex sec_A.4 Annex sec_A.4.1 |
| 93 | Annex sec_A.4.2 Annex sec_A.4.3 Table tab_q Figure fig_A.1 Table tab_A.2 Annex sec_A.5 Annex sec_A.5.1 |
| 94 | Annex sec_A.5.2 Annex sec_A.5.3 Annex sec_A.6 Annex sec_A.6.1 Annex sec_A.6.2 Annex sec_A.6.3 Annex sec_A.6.3.1 Annex sec_A.6.3.2 |
| 95 | Annex sec_A.6.3.2.1 Annex sec_A.6.4 Annex sec_A.6.5 Annex sec_A.7 Annex sec_A.7.1 Annex sec_A.7.2 Table tab_A.3 Annex sec_A.7.3 |
| 96 | Table tab_A.4 Annex sec_A.7.4 Annex sec_A.8 Annex sec_A.8.1 Annex sec_A.8.1.1 Annex sec_A.8.1.2 |
| 97 | Annex sec_A.8.1.3 Annex sec_A.8.2 Annex sec_A.9 Annex sec_A.9.1 Annex sec_A.9.1.1 Annex sec_A.9.1.2 Annex sec_A.9.1.3 |
| 98 | Annex sec_A.9.2 Annex sec_A.10 Annex sec_A.10.1 Annex sec_A.10.1.1 Annex sec_A.10.1.2 Annex sec_A.10.2 Annex sec_A.11 Annex sec_A.11.1 Annex sec_A.11.1.1 Annex sec_A.11.1.2 Annex sec_A.11.1.3 |
| 99 | Table tab_A.5 Annex sec_A.11.1.4 Annex sec_A.11.1.5 Annex sec_A.11.2 Annex sec_A.12 Annex sec_A.12.1 Annex sec_A.12.1.1 Annex sec_A.12.1.2 Annex sec_A.12.1.3 |
| 100 | Annex sec_A.12.2 Annex sec_A.12.2.1 Annex sec_A.12.2.2 Annex sec_A.12.2.3 Annex sec_A.13 Annex sec_A.13.1 Annex sec_A.13.2 |
| 101 | Annex sec_A.14 Annex sec_A.14.1 Annex sec_A.14.2 Annex sec_A.15 |
| 102 | Annex sec_A.16 Annex sec_A.16.1 Annex sec_A.16.2 Annex sec_A.16.3 Table tab_A.6 |
| 103 | Table tab_ab Figure fig_A.2 Table tab_A.7 |
| 104 | Annex sec_A.16.4 Table tab_A.8 |
| 105 | Table tab_ac Figure fig_A.3 Table tab_A.9 |
| 106 | Annex sec_A.16.5 Table tab_A.10 |
| 107 | Table tab_ad Figure fig_A.4 |
| 108 | Table tab_ae Figure fig_A.5 |
| 109 | Table tab_A.11 |
| 110 | Annex sec_A.16.6 Table tab_A.12 Table tab_A.13 |
| 111 | Table tab_ag Figure fig_A.6 Table tab_A.14 Table tab_A.15 |
| 112 | Annex sec_A.16.7 Table tab_A.16 Table tab_ah Figure fig_A.7 |
| 113 | Table tab_A.17 Table tab_A.18 Annex sec_A.16.8 Table tab_A.19 |
| 114 | Annex sec_B Annex sec_B.1 Annex B (informative) Mathematical models for liquid heating collectors |
| 115 | Annex sec_B.2 |
| 116 | Table tab_aj Figure fig_B.1 |
| 118 | Annex sec_C Annex sec_C.1 Annex sec_C.2 Annex C (normative) Properties of water |
| 119 | Annex sec_C.3 Annex sec_C.4 |
| 121 | Annex sec_D Annex sec_D.1 Annex sec_D.2 Annex D (informative) General guidelines for the assessment of uncertainty in solar collector efficiency testing |
| 123 | Annex sec_D.3 |
| 125 | Annex sec_E Table tab_am Figure fig_E.1 Annex E (informative) Measurement of the velocity weighted mean temperature |
| 126 | Table tab_an Figure fig_E.2 |
| 127 | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Reference ref_5 Bibliography |
