The 2021 IPC® provides minimum regulations for plumbing facilities and provides for the acceptance of new and innovative products, materials, and systems. In October 2019, the Code Council released an independent study comparing model plumbing codes. Important changes in the 2021 IPC include: Multiple-user toilet facilities to serve all genders are now permitted. Two new methods for relining/rehabilitation of existing sewers are added. Accommodations for mounted roof top solar panels over vent terminals is added. CSA B805/ICC 805 Rainwater Harvesting Systems is allowed as an alternative design method. Plumbing provisions from ICC A117.1-2017 Standard for Usable and Accessible Buildings and Facilities are now included.

PDF Catalog

PDF Pages	PDF Title
1	2021 IPC® INTERNATIONAL PLUMBING CODE®
2	2021 IPC® INTERNATIONAL PLUMBING CODE® TITLE PAGE
3	COPYRIGHT
4	PREFACE
10	ARRANGEMENT AND FORMAT OF THE 2021 IPC
14	TABLE OF CONTENTS
18	CHAPTER 1 SCOPE AND ADMINISTRATION PART 1—SCOPE AND APPLICATION SECTION 101 SCOPE AND GENERAL REQUIREMENTS SECTION 102 APPLICABILITY
19	PART 2—ADMINISTRATION AND ENFORCEMENT SECTION 103 CODE COMPLIANCE AGENCY SECTION 104 DUTIES AND POWERS OF THE CODE OFFICIAL
20	SECTION 105 APPROVAL SECTION 106 PERMITS
22	SECTION 107 TEMPORARY EQUIPMENT, SYSTEMS AND USES SECTION 108 INSPECTIONS AND TESTING
23	SECTION 109 FEES SECTION 110 CONSTRUCTION DOCUMENTS
24	SECTION 111 NOTICE OF APPROVAL SECTION 112 SERVICE UTILITIES SECTION 113 STOP WORK ORDER SECTION 114 MEANS OF APPEALS
25	SECTION 115 VIOLATIONS
26	CHAPTER 2 DEFINITIONS SECTION 201 GENERAL SECTION 202 GENERAL DEFINITIONS
34	CHAPTER 3 GENERAL REGULATIONS SECTION 301 GENERAL SECTION 302 EXCLUSION OF MATERIALS DETRIMENTAL TO THE SEWER SYSTEM SECTION 303 MATERIALS
35	SECTION 304 RODENTPROOFING SECTION 305 PROTECTION OF PIPES AND PLUMBING SYSTEM COMPONENTS SECTION 306 TRENCHING, EXCAVATION AND BACKFILL
36	SECTION 307 STRUCTURAL SAFETY SECTION 308 PIPING SUPPORT
37	TABLE 308.5 HANGER SPACIN SECTION 309 FLOOD HAZARD RESISTANCE
38	SECTION 310 WASHROOM AND TOILET ROOM REQUIREMENTS SECTION 311 TOILET FACILITIES FOR WORKERS SECTION 312 TESTS AND INSPECTIONS
39	SECTION 313 EQUIPMENT EFFICIENCIES SECTION 314 CONDENSATE DISPOSAL [M] TABLE 314.2.2 CONDENSATE DRAIN S
40	SECTION 315 PENETRATIONS SECTION 316 ALTERNATIVE ENGINEERED DESIGN
42	CHAPTER 4 FIXTURES, FAUCETS AND FIXTURE FITTINGS SECTION 401 GENERAL SECTION 402 FIXTURE MATERIALS SECTION 403 MINIMUM PLUMBING FACILITIES TABLE 403.1 MINIMUM NUMBER OF REQUIRED PLUMBING FIXTURESa (See Sections 403.1.1 and 403.2)
43	TABLE 403.1—continued MINIMUM NUMBER OF REQUIRED PLUMBING FIXTURESa (See Sections 403.1.1 and 403.2)
44	TABLE 403.1—continued MINIMUM NUMBER OF REQUIRED PLUMBING FIXTURESa (See Sections 403.1.1 and 403.2)
46	SECTION 404 ACCESSIBLE PLUMBING FACILITIES SECTION 405 INSTALLATION OF FIXTURES
48	SECTION 406 AUTOMATIC CLOTHES WASHERS SECTION 407 BATHTUBS SECTION 408 BIDETS SECTION 409 DISHWASHING MACHINES SECTION 410 DRINKING FOUNTAINS
49	SECTION 411 EMERGENCY SHOWERS AND EYEWASH STATIONS SECTION 412 FAUCETS AND FIXTURE FITTINGS
50	SECTION 413 FLOOR AND TRENCH DRAINS SECTION 414 FLOOR SINKS SECTION 415 FLUSHING DEVICES FOR WATER CLOSETS AND URINALS
51	SECTION 416 FOOD WASTE DISPOSER UNITS SECTION 417 GARBAGE CAN WASHERS SECTION 418 LAUNDRY TRAYS SECTION 419 LAVATORIES SECTION 420 MANUAL FOOD AND BEVERAGE DISPENSING EQUIPMENT SECTION 421 SHOWERS
53	SECTION 422 SINKS SECTION 423 SPECIALTY PLUMBING FIXTURES SECTION 424 URINALS SECTION 425 WATER CLOSETS SECTION 426 WHIRLPOOL BATHTUBS
54	CHAPTER 5 WATER HEATERS SECTION 501 GENERAL SECTION 502 INSTALLATION
55	SECTION 503 CONNECTIONS SECTION 504 SAFETY DEVICES
56	SECTION 505 INSULATION
58	CHAPTER 6 WATER SUPPLY AND DISTRIBUTION SECTION 601 GENERAL SECTION 602 WATER REQUIRED
59	SECTION 603 WATER SERVICE SECTION 604 DESIGN OF BUILDING WATER DISTRIBUTION SYSTEM TABLE 604.3 WATER DISTRIBUTION SYSTEM DESIGN CRITERIA REQUIRED CAPACITY AT FIXTURE SUPPLY PIPE OUTLETS
60	TABLE 604.4 MAXIMUM FLOW RATES AND CONSUMPTION FOR PLUMBING FIXTURES AND FIXTURE FITTINGS TABLE 604.5 MINIMUM SIZES OF FIXTURE WATER SUPPLY PIPES
61	TABLE 604.10.1 MANIFOLD SIZING SECTION 605 MATERIALS, JOINTS AND CONNECTIONS TABLE 605.3 WATER SERVICE PIPE
62	TABLE 605.4 WATER DISTRIBUTION PIPE TABLE 605.7 VALVES
63	TABLE 605.5 PIPE FITTINGS TABLE 605.8 MANUFACTURED PIPE NIPPLES
66	SECTION 606 INSTALLATION OF THE BUILDING WATER DISTRIBUTION SYSTEM
67	TABLE 606.5.4 SIZES FOR OVERFLOW PIPES FOR WATER SUPPLY TANKS TABLE 606.5.7 SIZE OF DRAIN PIPES FOR WATER TANKS SECTION 607 HOT WATER SUPPLY SYSTEM
68	SECTION 608 PROTECTION OF POTABLE WATER SUPPLY
69	TABLE 608.1 APPLICATION OF BACKFLOW PREVENTERS
70	FIGURE 608.9.1 PICTOGRAPH—DO NOT DRINK
71	TABLE 608.9.2.2 SIZE OF PIPE IDENTIFICATION
72	TABLE 608.16.1 MINIMUM REQUIRED AIR GAPS
74	TABLE 608.18.1 DISTANCE FROM CONTAMINATION TO PRIVATE WATER SUPPLIES AND PUMP SUCTION LINES SECTION 609 HEALTH CARE PLUMBING
75	SECTION 610 DISINFECTION OF POTABLE WATER SYSTEM SECTION 611 DRINKING WATER TREATMENT UNITS SECTION 612 SOLAR SYSTEMS SECTION 613 TEMPERATURE CONTROL DEVICES AND VALVES
76	CHAPTER 7 SANITARY DRAINAGE SECTION 701 GENERAL SECTION 702 MATERIALS TABLE 702.1 ABOVE-GROUND DRAINAGE AND VENT PIPE
77	TABLE 702.2 UNDERGROUND BUILDING DRAINAGE AND VENT PIPE TABLE 702.3 BUILDING SEWER PIPE
78	TABLE 702.4 PIPE FITTINGS SECTION 703 BUILDING SEWER SECTION 704 DRAINAGE PIPING INSTALLATION TABLE 704.1 SLOPE OF HORIZONTAL DRAINAGE PIPE
79	SECTION 705 JOINTS
81	TABLE 705.18 CAULKING FERRULE SPECIFICATIONS TABLE 705.19 SOLDERING BUSHING SPECIFICATIONS SECTION 706 CONNECTIONS BETWEEN DRAINAGE PIPING AND FITTINGS
82	TABLE 706.3 FITTINGS FOR CHANGE IN DIRECTION SECTION 707 PROHIBITED JOINTS AND CONNECTIONS SECTION 708 CLEANOUTS
83	SECTION 709 FIXTURE UNITS TABLE 709.2 DRAINAGE FIXTURE UNITS FOR FIXTURE DRAINS OR TRAPS
84	TABLE 709.1 DRAINAGE FIXTURE UNITS FOR FIXTURES AND GROUPS
85	SECTION 710 DRAINAGE SYSTEM SIZING TABLE 710.1(1) BUILDING DRAINS AND SEWERS TABLE 710.1(2) HORIZONTAL FIXTURE BRANCHES AND STACKSa SECTION 711 OFFSETS IN DRAINAGE PIPING IN BUILDINGS OF FIVE STORIES OR MORE
86	SECTION 712 SUMPS AND EJECTORS
87	TABLE 712.4.2 MINIMUM CAPACITY OF SEWAGE PUMP OR SEWAGE EJECTOR SECTION 713 COMPUTERIZED DRAINAGE DESIGN SECTION 714 BACKWATER VALVES SECTION 715 VACUUM DRAINAGE SYSTEMS SECTION 716 REPLACEMENT OF UNDERGROUND BUILDING SEWERS AND BUILDING DRAINS BY PIPE-BURSTING METHODS
88	SECTION 717 RELINING BUILDING SEWERS AND BUILDING DRAINS SECTION 718 REHABILITATION OF BUILDING SEWERS AND BUILDING DRAINS
90	CHAPTER 8 INDIRECT/SPECIAL WASTE SECTION 801 GENERAL SECTION 802 INDIRECT WASTES
91	SECTION 803 SPECIAL WASTES
92	CHAPTER 9 VENTS SECTION 901 GENERAL SECTION 902 MATERIALS SECTION 903 VENT TERMINALS
93	SECTION 904 OUTDOOR VENT EXTENSIONS SECTION 905 VENT CONNECTIONS AND GRADES SECTION 906 VENT PIPE SIZING
94	TABLE 906.1 SIZE AND DEVELOPED LENGTH OF STACK VENTS AND VENT STACKS
95	TABLE 906.5.1 SIZE AND LENGTH OF SUMP VENTS SECTION 907 VENTS FOR STACK OFFSETS SECTION 908 RELIEF VENTS—STACKS OF MORE THAN 10 BRANCH INTERVALS
96	SECTION 909 FIXTURE VENTS TABLE 909.1 MAXIMUM DISTANCE OF FIXTURE TRAP FROM VENT SECTION 910 INDIVIDUAL VENT SECTION 911 COMMON VENT TABLE 911.3 COMMON VENT SIZES SECTION 912 WET VENTING
97	TABLE 912.3 WET VENT SIZE SECTION 913 WASTE STACK VENT TABLE 913.4 WASTE STACK VENT SIZE SECTION 914 CIRCUIT VENTING
98	SECTION 915 COMBINATION WASTE AND VENT SYSTEM TABLE 915.2.2 SIZE OF COMBINATION WASTE AND VENT PIPE SECTION 916 ISLAND FIXTURE VENTING SECTION 917 SINGLE-STACK VENT SYSTEM
99	TABLE 917.2 SINGLE STACK SIZE SECTION 918 AIR ADMITTANCE VALVES
100	SECTION 919 ENGINEERED VENT SYSTEMS TABLE 919.2 MINIMUM DIAMETER AND MAXIMUM LENGTH OF INDIVIDUAL BRANCH FIXTURE VENTS AND INDIVIDUAL FIXTURE HEADER VENTS FOR SMOOTH PIPES EQUATION 9-1 SECTION 920 COMPUTERIZED VENT DESIGN
102	CHAPTER 10 TRAPS, INTERCEPTORS AND SEPARATORS SECTION 1001 GENERAL SECTION 1002 TRAP REQUIREMENTS
103	SECTION 1003 INTERCEPTORS AND SEPARATORS
104	TABLE 1003.3.5.1 CAPACITY OF GREASE INTERCEPTORS
105	SECTION 1004 MATERIALS, JOINTS AND CONNECTIONS
106	CHAPTER 11 STORM DRAINAGE SECTION 1101 GENERAL SECTION 1102 MATERIALS TABLE 1102.4 BUILDING STORM SEWER PIPE
107	TABLE 1102.5 SUBSOIL DRAIN PIPE TABLE 1102.7 PIPE FITTINGS SECTION 1103 TRAPS SECTION 1104 CONDUCTORS AND CONNECTIONS SECTION 1105 ROOF DRAINS
108	SECTION 1106 SIZE OF CONDUCTORS, LEADERS AND STORM DRAINS EQUATION 11-1 TABLE 1106.2 STORM DRAIN PIPE SIZING TABLE 1106.3 VERTICAL LEADER SIZING
109	FIGURE 1106.1(1) 100-YEAR, 1-HOUR RAINFALL (INCHES) WESTERN UNITED STATES
110	FIGURE 1106.1(2) 100-YEAR, 1-HOUR RAINFALL (INCHES) CENTRAL UNITED STATES
111	FIGURE 1106.1(3) 100-YEAR, 1-HOUR RAINFALL (INCHES) EASTERN UNITED STATES
112	FIGURE 1106.1(4) 100-YEAR, 1-HOUR RAINFALL (INCHES) ALASKA
113	FIGURE 1106.1(5) 100-YEAR, 1-HOUR RAINFALL (INCHES) HAWAII
114	TABLE 1106.6 HORIZONTAL GUTTER SIZING SECTION 1107 SIPHONIC ROOF DRAINAGE SYSTEMS SECTION 1108 SECONDARY (EMERGENCY) ROOF DRAINS SECTION 1109 COMBINED SANITARY AND STORM PUBLIC SEWER SECTION 1110 CONTROLLED FLOW ROOF DRAIN SYSTEMS
115	SECTION 1111 SUBSOIL DRAINS SECTION 1112 BUILDING SUBDRAINS SECTION 1113 SUMPS AND PUMPING SYSTEMS
116	CHAPTER 12 SPECIAL PIPING AND STORAGE SYSTEMS SECTION 1201 GENERAL SECTION 1202 MEDICAL GASES SECTION 1203 OXYGEN SYSTEMS
118	CHAPTER 13 NONPOTABLE WATER SYSTEMS SECTION 1301 GENERAL FIGURE 1301.3 PICTOGRAPH—DO NOT DRINK
120	SECTION 1302 ON-SITE NONPOTABLE WATER REUSE SYSTEMS
121	TABLE 1302.7.1 LOCATION OF NONPOTABLE WATER REUSE STORAGE TANKS
122	SECTION 1303 NONPOTABLE RAINWATER COLLECTION AND DISTRIBUTION SYSTEMS
123	TABLE 1303.10.1 LOCATION OF RAINWATER STORAGE TANKS
124	SECTION 1304 RECLAIMED WATER SYSTEMS
126	CHAPTER 14 SUBSURFACE GRAYWATER SOIL ABSORPTION SYSTEMS SECTION 1401 GENERAL SECTION 1402 SYSTEM DESIGN AND SIZING EQUATION 14-1
127	TABLE 1402.3 LOCATION OF SUBSURFACE GRAYWATER SOIL ABSORPTION SYSTEM SECTION 1403 INSTALLATION TABLE 1403.1.1 DESIGN LOADING RATE
128	TABLE 1403.2 DISTRIBUTION PIPE TABLE 1403.2 DISTRIBUTION PIPE
130	CHAPTER 15 REFERENCED STANDARDS ANSI ASHRAE ASME
132	ASPE
133	ASSE
135	ASTM
140	AWS AWWA
141	CISPI CSA
143	IAPMO
144	ICC ISEA MSS
145	NFPA NGWA NSF
146	PDI PSAI UL
148	APPENDIX A PLUMBING PERMIT FEE SCHEDULE TABLE A101 EXAMPLE OF PERMIT FEE SCHEDULE PERMIT ISSUANCE UNIT FEE SCHEDULE OTHER INSPECTIONS AND FEES
150	APPENDIX B RATES OF RAINFALL FOR VARIOUS CITIES TABLE B101 RATES OF RAINFALL FOR VARIOUS CITIESa
151	TABLE B101—continued RATES OF RAINFALL FOR VARIOUS CITIESa
152	TABLE B101—continued RATES OF RAINFALL FOR VARIOUS CITIESa
153	TABLE B101—continued RATES OF RAINFALL FOR VARIOUS CITIESa
154	APPENDIX C STRUCTURAL SAFETY SECTION C101 CUTTING, NOTCHING AND BORING IN WOOD MEMBERS
156	APPENDIX D DEGREE DAY AND DESIGN TEMPERATURES TABLE D101 DEGREE DAY AND DESIGN TEMPERATURESa FOR CITIES IN THE UNITED STATES
157	TABLE D101—continued DEGREE DAY AND DESIGN TEMPERATURESa FOR CITIES IN THE UNITED STATES
158	TABLE D101—continued DEGREE DAY AND DESIGN TEMPERATURESa FOR CITIES IN THE UNITED STATES
159	TABLE D101—continued DEGREE DAY AND DESIGN TEMPERATURESa FOR CITIES IN THE UNITED STATES
160	TABLE D101—continued DEGREE DAY AND DESIGN TEMPERATURESa FOR CITIES IN THE UNITED STATES
161	TABLE D101—continued DEGREE DAY AND DESIGN TEMPERATURESa FOR CITIES IN THE UNITED STATES
162	APPENDIX E SIZING OF WATER PIPING SYSTEM SECTION E101 GENERAL SECTION E102 INFORMATION REQUIRED SECTION E103 SELECTION OF PIPE SIZE
166	TABLE E103.3.1(1) SUMMATION OF DEVELOPED PIPE LENGTHS
167	TABLE E103.3.1(2) FITTING PRESSURE LOSSES EXPRESSED IN EQUIVALENT LENGTHS TABLE E103.3.1(3) TOTAL FRICTION LOSS EQUIVALENT PIPING LENGTH
168	FIGURE E103.3(1) EXAMPLE—SIZING
169	TABLE E103.3(1) RECOMMENDED TABULAR ARRANGEMENT FOR USE IN SOLVING PIPE SIZING PROBLEMS
170	TABLE E103.3(2) LOAD VALUES ASSIGNED TO FIXTURESa
171	TABLE E103.3(3) TABLE FOR ESTIMATING DEMAND
172	TABLE E103.3(3)—continued TABLE FOR ESTIMATING DEMAND TABLE E103.3(4) LOSS OF PRESSURE THROUGH TAPS AND TEES IN POUNDS PER SQUARE INCH (psi)
173	TABLE E103.3(5) ALLOWANCE IN EQUIVALENT LENGTHS OF PIPE FOR FRICTION LOSS IN VALVES AND THREADED FITTINGS (feet) TABLE E103.3(6) PRESSURE LOSS IN FITTINGS AND VALVES EXPRESSED AS EQUIVALENT LENGTH OF TUBEa (feet)
174	FIGURE E103.3(2) FRICTION LOSS IN SMOOTH PIPEa (TYPE K, ASTM B88 COPPER TUBING)
175	FIGURE E103.3(3) FRICTION LOSS IN SMOOTH PIPEa (TYPE L, ASTM B88 COPPER TUBING)
176	FIGURE E103.3(4) FRICTION LOSS IN SMOOTH PIPEa (TYPE M, ASTM B88 COPPER TUBING)
177	FIGURE E103.3(5) FRICTION LOSS IN FAIRLY SMOOTH PIPEa
178	FIGURE E103.3(6) FRICTION LOSS IN FAIRLY ROUGH PIPEa
179	FIGURE E103.3(7) FRICTION LOSS IN ROUGH PIPEa
180	SECTION E104 SELECTION OF PIPE SIZE SECTION E105 DETERMINATION OF PIPE VOLUMES
181	TABLE E104.1 MINIMUM SIZE OF WATER METERS, MAINS AND DISTRIBUTION PIPING BASED ON WATER SUPPLY FIXTURE UNIT VALUES (w.s.f.u.)
182	TABLE E104.1—continued MINIMUM SIZE OF WATER METERS, MAINS AND DISTRIBUTION PIPING BASED ON WATER SUPPLY FIXTURE UNIT VALUES (w.s.f.u.)
183	TABLE E105.1 INTERNAL VOLUME OF VARIOUS WATER DISTRIBUTION TUBING
184	[A] APPENDIX F BOARD OF APPEALS [A] SECTION F101 GENERAL
186	INDEX
198	RESOURCE A PLUMBING PROVISIONS EXCERPTED FROM: ICC A117.1–2017 STANDARD FOR ACCESSIBLE AND USABLE BUILDINGS AND FACILITIES
200	PLUMBING PROVISIONS EXCERPTED FROM: ICC A117.1-2017 STANDARD FOR ACCESSIBLE AND USABLE BUILDINGS AND FACILITIES TITLE PAGE
201	COPYRIGHT
202	TABLE OF CONTENTS
204	CHAPTER 1 APPLICATION AND ADMINISTRATION SECTION 101 TITLE SECTION 102 PURPOSE SECTION 103 HUMAN FACTOR PROVISIONS SECTION 104 COMPLIANCE ALTERNATIVES SECTION 105 CONVENTIONS SECTION 106 REFERENCED DOCUMENTS
205	FIGURE 105.4 GRAPHIC CONVENTION FOR FIGURES
206	SECTION 107 DEFINITIONS
210	CHAPTER 3 BUILDING BLOCKS SECTION 301 GENERAL SECTION 302 FLOOR SURFACES FIGURE 302.2 CARPET ON FLOOR SURFACES FIGURE 302.3 OPENINGS IN FLOOR SURFACES FIGURE 303.2 VERTICAL CHANGE IN LEVEL FIGURE 303.3 BEVELED CHANGES IN LEVEL SECTION 303 CHANGES IN LEVEL
211	SECTION 304 TURNING SPACE FIGURE 304.3.1.1 CIRCULAR TURNING SPACE – NEW BUILDINGS SIZE AND OVERLAP FIGURE 304.3.1.2 CIRCULAR TURNING SPACE – EXISTING BUILDINGS – SIZE AND OVERLAP FIGURE 304.3.2.1(A) T-SHAPED TURNING SPACE NEW BUILDINGS – OPTION 1
212	FIGURE 304.3.2.1(B) T-SHAPED TURNING SPACE NEW BUILDINGS – OPTION 2 FIGURE 304.3.2.1(C) T-SHAPED TURNING SPACE NEW BUILDINGS – OPTION 3 FIGURE 304.3.2.1.1 T-SHAPED TURNING SPACE NEW BUILDINGS – OVERLAP
213	FIGURE 304.3.2.2 T-SHAPED TURNING SPACE EXISTING BUILDINGS – SIZE FIGURE 304.3.2.2.1 T-SHAPED TURNING SPACE – EXISTING BUILDINGS OVERLAP SECTION 305 CLEAR FLOOR SPACE FIGURE 305.3.1 SIZE OF CLEAR FLOOR SPACE – NEW BUILDINGS FIGURE 305.3.2 SIZE OF CLEAR FLOOR SPACE – EXISTING BUILDINGS
214	FIGURE 305.5(A) POSITION OF CLEAR FLOOR SPACE – FORWARD FIGURE 305.5(B) POSITION OF CLEAR FLOOR SPACE – PARALLEL FIGURE 305.7.1 MANEUVERING CLEARANCE IN AN ALCOVE PARALLEL APPROACH FIGURE 305.7.2 MANEUVERING CLEARANCE IN AN ALCOVE FORWARD APPROACH SECTION 306 KNEE AND TOE CLEARANCE
215	FIGURE 306.2(A) TOE CLEARANCE – ELEVATION FIGURE 306.2(B) TOE CLEARANCE – PLAN FIGURE 306.3(A) KNEE CLEARANCE – ELEVATION FIGURE 306.3(B) KNEE CLEARANCE – PLAN
216	SECTION 307 PROTRUDING OBJECTS FIGURE 307.2 LIMITS OF PROTRUDING OBJECTS FIGURE 307.3(A) POST-MOUNTED PROTRUDING OBJECTS FIGURE 307.3(B) POST-MOUNTED PROTRUDING OBJECTS
217	FIGURE 307.4 REDUCED VERTICAL CLEARANCE SECTION 308 REACH RANGES FIGURE 308.2.1 UNOBSTRUCTED FORWARD REACH FIGURE 308.2.2 OBSTRUCTED HIGH FORWARD REACH
218	FIGURE 308.3.1 UNOBSTRUCTED SIDE REACH FIGURE 308.3.2(A) OBSTRUCTED HIGH SIDE REACH FIGURE 308.3.2(B) OBSTRUCTED HIGH SIDE REACH SECTION 309 OPERABLE PARTS
219	FIGURE 309.1 OPERABLE PARTS – EXCEPTION 3
220	CHAPTER 6 PLUMBING ELEMENTS AND FACILITIES SECTION 601 GENERAL SECTION 602 DRINKING FOUNTAINS AND BOTTLE FILLING STATIONS FIGURE 602.2.1(A) CLEAR FLOOR SPACE AT WHEELCHAIR DRINKING FOUNTAINS FIGURE 602.2.1(B) CLEAR FLOOR SPACE AT WHEELCHAIR DRINKING FOUNTAINS – PRIMARILY FOR CHILDREN’S USE EXCEPTION FIGURE 602.2.3 WHEELCHAIR DRINKING FOUNTAIN SPOUT HEIGHT AND LOCATION
221	FIGURE 602.2.4 WHEELCHAIR DRINKING FOUNTAIN SPOUT LOCATION FIGURE 602.3.2 STANDING USE DRINKING FOUNTAIN SPOUT HEIGHT AND LOCATION FIGURE 602.3.3 STANDING USE DRINKING FOUNTAIN SPOUT LOCATION SECTION 603 TOILET AND BATHING ROOMS
222	TABLE 603.6 MAXIMUM REACH DEPTH AND HEIGHT SECTION 604 WATER CLOSETS AND TOILET COMPARTMENTS FIGURE 604.2 WATER CLOSET LOCATION
223	FIGURE 604.3 SIZE OF CLEARANCE FOR WATER CLOSET FIGURE 604.4 WATER CLOSET SEAT HEIGHT
224	FIGURE 604.5.1 SIDE-WALL GRAB BAR FOR WATER CLOSET FIGURE 604.5.2 REAR-WALL GRAB BAR FOR WATER CLOSET
225	FIGURE 604.7.1(A) DISPENSER OUTLET LOCATION – PROTRUDING DISPENSER BELOW GRAB BAR FIGURE 604.7.1(B) DISPENSER OUTLET LOCATION PROTRUDING DISPENSER ABOVE GRAB BAR FIGURE 604.7.1(C) DISPENSER OUTLET LOCATION RECESSED DISPENSER
226	FIGURE 604.7.1(D) DISPENSER OUTLET LOCATION DISPENSER IN FRONT OF WATER CLOSET – EXCEPTION FIGURE 604.9.2(A) WHEELCHAIR TOILET COMPARTMENTS WALL HUNG CLOSET, ADULT60 min152559 min1500FIGURE 604.9.2(B)WHEELCHAIR TOILET FIGURE 604.9.2(B) WHEELCHAIR TOILET COMPARTMENTS FLOOR MOUNTED WATER CLOSET, ADULT – WALL HUNG AND FLOOR MOUNTED WATER CLOSET, CHILDREN
227	FIGURE 604.9.2.3 WHEELCHAIR TOILET COMPARTMENTS ALTERNATE WHEELCHAIR TOILET COMPARTMENT FIGURE 604.9.3(A) WHEELCHAIR TOILET COMPARTMENT DOORS DOOR SWINGING INTO THE WHEELCHAIR TOILET COMPARTMENT
228	FIGURE 604.9.3(B) WHEELCHAIR TOILET COMPARTMENT DOORS EXCEPTION 3 – ALTERNATE WHEELCHAIR COMPARTMENT FIGURE 604.9.3.1(A) WHEELCHAIR TOILET COMPARTMENT DOOR OPENING LOCATION – DOOR SWINGING IN ON FRONT WALL OF PARTITION FIGURE 604.9.3.1(B) WHEELCHAIR TOILET COMPARTMENT DOOR OPENING LOCATION DOOR SWINGING IN ON SIDE WALL OF PARTITIONS
229	TABLE 604.9.3.1 —DOOR OPENING LOCATION FIGURE 604.9.5(A) TOE CLEARANCE – ELEVATION FIGURE 604.9.5(B) TOE CLEARANCE – PLAN
230	FIGURE 604.10.1 AMBULATORY COMPARTMENT FIGURE 604.11.2 CHILDREN’S WATER CLOSET LOCATION FIGURE 604.11.4 CHILDREN’S WATER CLOSET HEIGHT
231	FIGURE 604.11.7(A) CHILDREN’S DISPENSER OUTLET – LOCATION FIGURE 604.11.7(B) CHILDREN’S DISPENSER OUTLET – EXCEPTION SECTION 605 URINALS FIGURE 605.2(A) HEIGHT AND DEPTH OF URINAL WALL HUNG TYPE
232	FIGURE 605.2(B) HEIGHT AND DEPTH OF URINAL STALL TYPE SECTION 606 LAVATORIES AND SINKS FIGURE 606.3 HEIGHT OF LAVATORIES AND SINKS
233	SECTION 607 BATHTUBS FIGURE 607.2(A) CLEARANCE FOR BATHTUBS WITH REMOVABLE IN TUB SEATS FIGURE 607.2(B) CLEARANCE FOR BATHTUBS WITH SEAT AT HEAD END OF TUB
234	FIGURE 607.4.1(A) GRAB BARS FOR BATHTUBS WITH SEAT AT HEAD END OF TUB – ELEVATION FIGURE 607.4.1(B) GRAB BARS FOR BATHTUBS WITH SEAT AT HEAD END OF TUB – PLAN FIGURE 607.4.2(A) GRAB BARS FOR BATHTUBS WITH REMOVABLE SEATS – ELEVATION
235	FIGURE 607.4.2(B) GRAB BARS FOR BATHTUBS WITH REMOVABLE SEATS – PLAN FIGURE 607.5 LOCATION OF BATHTUB CONTROLS SECTION 608 SHOWER COMPARTMENTS FIGURE 608.2.1.1 TRANSFER-TYPE SHOWER COMPARTMENT SIZE
236	FIGURE 608.2.1.2(A) TRANSFER-TYPE SHOWER COMPARTMENT CLEARANCES NEW BUILDINGS – OPTION 1 FIGURE 608.2.1.2 (B) TRANSFER-TYPE SHOWER COMPARTMENT CLEARANCES NEW BUILDINGS – OPTION 2 FIGURE 608.2.1.2(C) TRANSFER-TYPE SHOWER COMPARTMENT CLEARANCES EXISTING BUILDINGS FIGURE 608.2.2.1 STANDARD ROLL-IN-TYPE SHOWER COMPARTMENT SIZE
237	FIGURE 608.2.2.2 STANDARD ROLL-IN-TYPE SHOWER COMPARTMENT CLEARANCE FIGURE 608.2.3.1 ALTERNATE ROLL-IN-TYPE SHOWER COMPARTMENT SIZE
238	FIGURE 608.3.1(A) GRAB BARS IN TRANSFER-TYPE SHOWER – ELEVATION FIGURE 608.3.2(A) GRAB BARS IN STANDARD ROLL-IN-TYPE SHOWER ELEVATION FIGURE 608.3.1(B) GRAB BARS IN TRANSFER-TYPE SHOWER – PLAN FIGURE 608.3.2(B) GRAB BARS IN STANDARD ROLL-IN-TYPE SHOWER PLAN
239	FIGURE 608.3.3(A) GRAB BARS IN ALTERNATE ROLL-IN-TYPE SHOWER – ELEVATION FIGURE 608.3.3(B) GRAB BARS IN ALTERNATE ROLL-IN-TYPE SHOWER – PLAN FIGURE 608.4.1 TRANSFER-TYPE SHOWER CONTROLS AND HAND SHOWER LOCATION FIGURE 608.4.2 STANDARD ROLL-IN-TYPE SHOWER CONTROLS AND HAND SHOWER LOCATION
240	FIGURE 608.4.3(A) ALTERNATE ROLL-IN-TYPE SHOWER CONTROLS AND HAND SHOWER LOCATION – END WALL – ELEVATION FIGURE 608.4.3(B) ALTERNATE ROLL-IN-TYPE SHOWER CONTROLS AND HAND SHOWER LOCATION – CONTROL WALL – ELEVATION SECTION 609 GRAB BARS
241	FIGURE 609.2 SIZE OF GRAB BARS FIGURE 609.3 SPACING OF GRAB BARS FIGURE 609.4.2(A) POSITIONS OF CHILDREN’S GRAB BARS SIDE-WALL VIEW
242	FIGURE 609.4.2(B) POSITIONS OF CHILDREN’S GRAB BARS REAR-WALL VIEW SECTION 610 SEATS FIGURE 610.2(A) BATHTUB SEATS REMOVABLE IN-TUB SEATS FIGURE 610.2(B) BATHTUB SEATS SEAT PROVIDED AT HEAD END OF TUB
243	FIGURE 610.3.1 RECTANGULAR SHOWER COMPARTMENT SEATS FIGURE 610.3.2 L-SHAPED SHOWER COMPARTMENT SEATS SECTION 611 WASHING MACHINES AND CLOTHES DRYERS
244	FIGURE 611.2(A) CLEAR FLOOR SPACE – TOP LOADING FIGURE 611.2(B) CLEAR FLOOR SPACE – FRONT LOADING FIGURE 611.4(A) HEIGHT OF LAUNDRY EQUIPMENT – TOP LOADING FIGURE 611.4(B) HEIGHT OF LAUNDRY EQUIPMENT – FRONT LOADING
245	SECTION 612 SAUNAS AND STEAM ROOMS
246	CHAPTER 8 SPECIAL ROOMS AND SPACES SECTION 801 GENERAL SECTION 804 KITCHENS
247	FIGURE 804.2.1(A) PASS-THROUGH KITCHEN CLEARANCE FIGURE 804.2.1(B) PASS-THROUGH KITCHEN CLEARANCE FIGURE 804.2.2(A) U-SHAPED KITCHEN CLEARANCE FIGURE 804.2.2(B) U-SHAPED KITCHEN CLEARANCE
248	FIGURE 804.2.2(C) U-SHAPED KITCHEN CLEARANCE – EXCEPTION
250	CHAPTER 11 DWELLING UNITS AND SLEEPING UNITS SECTION 1101 GENERAL SECTION 1102 ACCESSIBLE UNITS
251	SECTION 1103 TYPE A UNITS
252	FIGURE 1103.11.2.4(A) WATER CLOSETS IN TYPE A UNITS – WATER CLOSET LOCATION
253	FIGURE 1103.11.2.4(B) WATER CLOSETS IN TYPE A UNITS – MINIMUM CLEARANCE FIGURE 1103.11.2.4(C) WATER CLOSETS IN TYPE A UNITS – CLEARANCE WITH LAVATORY (OVERLAP EXCEPTION) FIGURE 1103.11.2.4(D) WATER CLOSETS IN TYPE A UNITS – WATER CLOSET SEAT HEIGHT FIGURE 1103.11.2.5.1(A) CLEARANCE FOR BATHTUBS IN TYPE A UNITS WITH REMOVABLE SEAT FIGURE 1103.11.2.5.1(B) CLEARANCE FOR BATHTUBS IN TYPE A UNITS WITH PERMANENT SEAT
254	FIGURE 1103.11.2.5.2 STANDARD ROLL-IN-TYPE SHOWER COMPARTMENT IN TYPE A UNITS FIGURE 1103.12.1.1 MINIMUM KITCHEN CLEARANCE IN TYPE A UNITS
255	FIGURE 1103.12.1.2(A) U-SHAPED KITCHEN CLEARANCE IN TYPE A UNITS FIGURE 1103.12.1.2(B) U-SHAPED KITCHEN CLEARANCE IN TYPE A UNITS EXCEPTION FIGURE 1103.12.3 WORK SURFACE IN KITCHEN FOR TYPE A UNITS
256	FIGURE 1103.12.4 KITCHEN SINK FOR TYPE A UNITS
257	SECTION 1104 TYPE B UNITS FIGURE 1104.1.1 CLEAR FLOOR SPACE FOR TYPE B UNITS
258	FIGURE 1104.9 REACH OVER A KITCHEN OR BATHROOM CABINET
259	FIGURE 1104.11.1.1 SWING-UP GRAB BARS FOR WATER CLOSETS
260	FIGURE 1104.11.3.1.1 LAVATORY IN TYPE B UNITS – OPTION A BATHROOMS FIGURE 1104.11.3.1.2(A) CLEARANCE AT WATER CLOSETS IN TYPE B UNITS WATER CLOSET LOCATION FIGURE 1104.11.3.1.2(B) CLEARANCE AT WATER CLOSETS IN TYPE B UNITS CLEARANCE WIDTH AND DEPTH
261	FIGURE 1104.11.3.1.2(C) CLEARANCE AT WATER CLOSETS IN TYPE B UNITS INCREASED CLEARANCE DEPTH – FORWARD APPROACH FIGURE 1104.11.3.1.2(D) CLEARANCE AT WATER CLOSETS IN TYPE B UNITS CLEARANCE WITH LAVATORY OVERLAP
262	FIGURE 1104.11.3.1.3.1 PARALLEL APPROACH BATHTUB IN TYPE B UNITS – OPTION A BATHROOM
263	FIGURE 1104.11.3.1.3.2 FORWARD APPROACH BATHTUB IN TYPE B UNITS OPTION A BATHROOM FIGURE 1104.11.3.1.3.3(A) TRANSFER-TYPE SHOWER COMPARTMENT IN TYPE B UNITS FIGURE 1104.11.3.1.3.3(B) TRANSFER-TYPE SHOWER COMPARTMENT IN TYPE B UNITS EXCEPTION FIGURE 1104.11.3.2.1 LAVATORY IN TYPE B UNITS – OPTION B BATHROOM
264	FIGURE 1104.11.3.2.3.1 BATHROOM CLEARANCE IN TYPE B UNITS OPTION B BATHROOM FIGURE 1104.12.1.1 MINIMUM CLEARANCE IN TYPE B UNITS
265	FIGURE 1104.12.1.2(A) U-SHAPED KITCHEN CLEARANCE IN TYPE B UNITS FIGURE 1104.12.1.2(B) U-SHAPED KITCHEN CLEARANCE IN TYPE B UNITS – EXCEPTION
266	SECTION 1105 TYPE C (VISITABLE) UNITS
267	SECTION 1106 UNITS WITH COMMUNICATION FEATURES
268	ICC EVALUATION SERVICE
269	ICC LEARNING CENTER
270	ICC’S DIGITAL CODES LIBRARY
271	ICC MEMBERSHIP

Published By	Publication Date	Number of Pages
ICC	2021	271


PDF Format	Searchable	Printable	Preview Now

Standard Title	International Plumbing Code, 3rd Printing
Published Code	ICC
Publication Date	2021
Pages Count	271

ICC IPC 2021 1stptg

PDF Catalog

Related products