ISO 1997:2018
$13.00
Granulated cork and cork powder — Classification, properties and packing
| Published By | Publication Date | Number of Pages |
| ISO | 2018-10 | 10 |
This document specifies the classification and properties of granulated cork and cork powder before pressing, as well as the methods of packing.
Related products
-
ISO 19697:2016
Ships and marine technology — Navigation and ship operations — Electronic inclinometers Published By Publication…
-
ISO 19970:2017
Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels — Metering of gas as fuel on…
-
BS ISO 1997:2018
Granulated cork and cork powder. Classification, properties and packing Published By Publication Date Number of…
-
ISO 19973-2:2015
Pneumatic fluid power — Assessment of component reliability by testing — Part 2: Directional control…
-
ISO 19967-2:2019
Heat pump water heaters — Testing and rating for performance — Part 2: Heat pump…
-
ISO 1999:2013
Acoustics — Estimation of noise-induced hearing loss Published By Publication Date Number of Pages ISO…
-
ISO 2078:1993/Amd 1:2015
Textile glass — Yarns — Designation — Amendment 1 Published By Publication Date Number of…
-
ISO 19973-5:2015
Pneumatic fluid power — Assessment of component reliability by testing — Part 5: Non-return valves,…
-
ISO 6018:1987
Orthopaedic implants — General requirements for marking, packaging and labelling Published By Publication Date Number…
-
ISO 19097-1:2018
Méthode d’essai accéléré de durabilité des anodes à oxydes métalliques mixtes pour la protection cathodique…
-
ISO 19979:2018
Ophthalmic optics — Contact lenses — Hygienic management of multipatient use trial contact lenses Published…
-
ISO 4997:2015
Cold-reduced carbon steel sheet of structural quality Published By Publication Date Number of Pages ISO…
-
ISO 19976-2:2019
Copper, lead and zinc sulfide concentrates — Determination of cadmium — Part 2: Acid digestion…
-
ISO 19897:2019
Ships and marine technology — Marine evacuation systems — Testing under conditions of icing Published…
-
ISO 1927-6:2012
Produits réfractaires monolithiques (non façonnés) — Partie 6: Détermination des propriétés physiques Published By Publication…
-
ISO 1797-1:2011
Dentistry — Shanks for rotary instruments — Part 1: Shanks made of metals Published By…
-
BS ISO 19097-2:2018
Accelerated life test method of mixed metal oxide anodes for cathodic protection – Application in…
-
ISO 19973-4:2014
Pneumatic fluid power — Assessment of component reliability by testing — Part 4: Pressure regulators…
-
BS ISO 1997:2018 – TC:2020 Edition
Tracked Changes. Granulated cork and cork powder. Classification, properties and packing Published By Publication Date…
-
BS ISO 19927:2018
Fibre-reinforced plastic composites. Determination of interlaminar strength and modulus by double beam shear test Published…
-
ISO 2078:1993
Textile glass — Yarns — Designation Published By Publication Date Number of Pages ISO 1993-02…
-
ISO 1797:2017
Médecine bucco-dentaire — Queues pour instruments rotatifs et oscillants Published By Publication Date Number of…
-
BS EN ISO 2078:1994+A1:2015:2016 Edition
Textile glass. Yarns. Designation Published By Publication Date Number of Pages BSI 2016 12
-
ISO 1927-4:2012
Produits réfractaires monolithiques (non façonnés) — Partie 4: Détermination de la consistance des bétons Published…
-
ISO 2008:1987
Rubber latex, styrene-butadiene — Determination of volatile unsaturates Published By Publication Date Number of Pages…
-
BS ISO 19970:2017
Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels. Metering of gas as fuel on LNG…
-
ISO 1927-1:2012
Monolithic (unshaped) refractory products — Part 1: Introduction and classification Published By Publication Date Number…
-
ISO 19976-1:2019
Copper, lead and zinc sulfide concentrates — Determination of cadmium — Part 1: Flame atomic…
-
ISO 9197:2016
Paper, board and pulps — Determination of water-soluble chlorides Published By Publication Date Number of…
-
ISO/TR 19997:2018
Guidelines for good practices in zeta-potential measurement Published By Publication Date Number of Pages ISO…
-
ISO 14997:2011
Optics and photonics — Test methods for surface imperfections of optical elements Published By Publication…
-
ISO 14997:2017
Optics and photonics — Test methods for surface imperfections of optical elements Published By Publication…
-
ISO 2818:1994
Plastics — Preparation of test specimens by machining Published By Publication Date Number of Pages…
-
ISO 19971:2018
Space systems — Spacecraft and launch vehicle combined operation plan (COP) at launch site —…
-
ISO 2028:1999
Synthetic rubber latex — Preparation of dry polymer Published By Publication Date Number of Pages…
-
ISO 1927-2:2012
Produits réfractaires monolithiques (non façonnés) — Partie 2: Échantillonnage Published By Publication Date Number of…
-
ISO 19927:2018
Fibre-reinforced plastic composites — Determination of interlaminar strength and modulus by double beam shear test…
-
ISO 19097-2:2018
Méthode d’essai accéléré de durabilité des anodes à oxydes métalliques mixtes pour la protection cathodique…
-
ISO 2048:1990
Double-socket fittings for unplasticized poly(vinyl chloride) (PVC-U) pressure pipes with elastic sealing ring type joints…
-
BS ISO 19097-1:2018
Accelerated life test method of mixed metal oxide anodes for cathodic protection – Application in…
