{"id":194933,"date":"2024-10-19T12:22:08","date_gmt":"2024-10-19T12:22:08","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/ieee-442-2017\/"},"modified":"2024-10-25T04:53:06","modified_gmt":"2024-10-25T04:53:06","slug":"ieee-442-2017","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/ieee\/ieee-442-2017\/","title":{"rendered":"IEEE 442 2017"},"content":{"rendered":"
Revision Standard – Active. The measurement of theremal resistivity of soil and backfill materials to include concrete, engineered backfills, grout, rock, sand, and any otherre material used to encase the cable system installed in the ground is covered in this guide. A thorough knowledge of the theremal properties of a soil or backfill material enables the user to properly design, rate, and load underground cables. The method used is based on the theory that the rate of temperature rise of a line heat source is dependent upon the theremal constants of the medium in which it is placed. The designs for both laboratory and field theremal probes are also described in this guide.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
1<\/td>\n | IEEE Std 442\u2122-2017 Front cover <\/td>\n<\/tr>\n | ||||||
2<\/td>\n | Title page <\/td>\n<\/tr>\n | ||||||
4<\/td>\n | Important Notices and Disclaimers Concerning IEEE Standards Documents <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | Participants <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
10<\/td>\n | IMPORTANT NOTICE 1.\u2002Overview 1.1\u2002Scope 1.2\u2002Purpose 2.\u2002Normative references <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 3.\u2002Factors influencing soil thermal resistivity 3.1\u2002Factors influencing measurements <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 4.\u2002Test equipment 4.1\u2002Equipment required for field measurements <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 4.2\u2002Equipment required for laboratory measurements 5.\u2002Test methods 5.1\u2002Methods for field measurements <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 5.2\u2002Methods for laboratory measurements <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 6.\u2002Analysis of test results <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 6.1\u2002Sample calculation 6.2\u2002Interpretation of results <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | Annex A (informative) Multi-sensor field probe <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | Annex\u00a0B (informative) Single-sensor laboratory and field probes <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | Annex\u00a0C (informative) Slide hammer assembly <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | Annex\u00a0D (informative) Sample standard proctor <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | Annex\u00a0E (informative) Thermal dryout characteristics <\/td>\n<\/tr>\n | ||||||
29<\/td>\n | Annex\u00a0F (informative) Determine critical moisture content <\/td>\n<\/tr>\n | ||||||
30<\/td>\n | Annex\u00a0G (informative) Moisture migration <\/td>\n<\/tr>\n | ||||||
31<\/td>\n | Annex\u00a0H (informative) Glossary <\/td>\n<\/tr>\n | ||||||
32<\/td>\n | Annex\u00a0I (informative) Bibliography <\/td>\n<\/tr>\n | ||||||
33<\/td>\n | Back cover <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" IEEE Guide for Thermal Resistivity Measurements of Soils and Backfill Materials<\/b><\/p>\n |