BS EN 61784-5-14:2013:2014 Edition
$167.15
Industrial communication networks. Profiles – Installation of fieldbuses. Installation profiles for CPF 14
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 36 |
IEC 61784-5-14:2013 specifies the installation profiles for CPF 14 (EPA). Each CP installation profile is specified in a separate part of this standard. The IEC 61784 series is produced to facilitate the use of communication networks in industrial control systems. This second edition cancels and replaces the second edition published in 2010 and constitutes a technical revision. It includes the following changes: – requirements for CP 14/3 have been added, – recommendations for the applications about the linear/ring topology networks have been added, – Table A.2 and Table A.6 have been updated. This publication is to be read in conjunction with /2.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | English CONTENTS |
| 8 | INTRODUCTION Figure 1 – Standards relationships |
| 9 | 1 Scope 2 Normative references 3 Terms, definitions and abbreviated terms 4 CPF 14: Overview of installation profiles 5 Installation profile conventions |
| 10 | 6 Conformance to installation profiles |
| 11 | Annex A (Normative) CP 14/1, 14/2 and 14/3 (EPA) specific installation profile A.1 Installation profile scope A.2 Normative references A.3 Installation profile terms, definitions, and abbreviated terms A.3.1 Terms and definitions A.3.2 Abbreviated terms A.3.3 Conventions for installation profiles A.4 Installation planning A.4.1 General A.4.2 Planning requirements |
| 12 | Figures Figure A.1 – Example of EPA explosion-proof system |
| 13 | Figure A.2 – Earth of zener safety barrier Figure A.3 – Earth of isolated safety barrier |
| 14 | A.4.3 Network capabilities Figure A.4 – Three stars coupled to a ring topology Figure A.5 – Five daisy chain lines coupled to a ring topology |
| 15 | Figure A.6 – Five sub-rings coupled to a ring topology |
| 16 | Tables Table A.1 – Network characteristics for balanced cabling based on Ethernet Table A.2 – Network characteristics for optical fibre cabling |
| 17 | Figure A.7 – Example of power with Ethernet |
| 18 | A.4.4 Selection and use of cabling components Figure A.8 – Example of power supply over 0,2 A Figure A.9 – Example of power with Ethernet in linear/ring topology network Table A.3 – Information relevant to copper cable |
| 19 | Table A.4 – Information relevant to copper cable: fixed cables Table A.5 – Information relevant to copper cable: cords |
| 20 | Table A.6 – Information relevant to optical fibre cables |
| 21 | Table A.7 – Connectors for balanced cabling CPs based on Ethernet Table A.8 – Optical fibre connecting hardware |
| 22 | Table A.9 – Relationship between FOC and fibre type (CP 14/1, CP 14/2 and CP 14/3) Table A.10 – Specific connectors for balanced cabling based on Ethernet |
| 23 | Table A.11 – Requirements of sub-D and open style connector |
| 24 | Figure A.10 – Examples of earthing method for the linear/ring topologies network |
| 25 | A.4.5 Cabling planning documentation A.4.6 Verification of cabling planning specification A.5 Installation implementation A.5.1 General requirements A.5.2 Cable installation Table A.12 – Parameters for balanced cables |
| 26 | Table A.13 – Parameters for silica optical fibre cables Table A.14 – Parameters for POF optical fibre cables Table A.15 – Parameters for hard cladded silica optical fibre cables |
| 27 | A.5.3 Connector installation Figure A.11 – Pin assignment of sub-D connector |
| 28 | Table A.16 – Signal lines assignment of sub-D connector Table A.17 – Signal lines assignment of sub-D connectorfor a 1 000 Mbit/s base Ethernet |
| 29 | Figure A.12 – Example of a 4-pin open style connector Table A.18 – Signal lines assignment for a 4-pin open style connector |
| 30 | Figure A.13 – Example of a 6-pin open style connector Table A.19 – Signal lines assignment for a 6-pin open style connector |
| 31 | Figure A.14 – Example of an 8-pin open style connector Table A.20 – Signal lines assignment for an 8-pin open style connector (10/100 Mbps) |
| 32 | A.5.4 Terminator installation A.5.5 Device installation A.5.6 Coding and labelling A.5.7 Earthing and bonding of equipment and devices and shield cabling A.5.8 As-implemented cabling documentation A.6 Installation verification and installation acceptance test A.6.1 General A.6.2 Installation verification Table A.21 – Signal lines assignment for an 8-pin open style connector (1 000 Mbit/s) |
| 33 | A.6.3 Installation acceptance test |
| 34 | A.7 Installation administration A.8 Installation maintenance and installation troubleshooting |
